Havis C-DMM-3003 User manual



  C‐DMM‐3003_INST_7‐18


TOOLSREQUIRED:(sometoolsarenotneededforallvehicleinstallations)
•Socketset‐metric&standard•Drill&drillbits•Tapemeasure•Plasticnotchingtool
•Phillipsscrewdriver  •Trimremovaltools •Pencil/Marker


PARTSandHARDWARE:

QTY: DESCRIPTION:    PART#:  
1MaindashmountbracketCM009349
1DriversidemountingbracketCM009402
1Passengersidemountingbracket  CM009403
1PVCspacerwasherCM008582
2Nylon1/16”spacerwasherCM86600
21/4"NylocknutGSM30016
21/4"FlatwasherGSM31005
410‐32x1/2"MachinescrewGSM33118
410‐32KepsnutGSM30028
1VESAswiveladaptorCM009068

Notes:
TheC‐DMM‐3000swivelplateacceptsC‐MM‐301offsetbracketusedwithC‐MM‐2XXadaptors.
C‐MM‐2XXseriesadaptorbracketsarenotneededformostVESA75andotherHavisDockingStation
mountingapplications.
CM009068VESArotatorplategivesadditionalpositioningoptions,butisnotrequireddependingon
mountingpreference. 

ALWAYS!
•ReadallinstructionsbeforeinstallinganyHavis,Incproducts.
•Usehardwareprovidedwithinstallkit
INSTALLATIONINSTRUCTIONS
C‐DMM‐3003FlipUpDashMonitorMount
2015‐2019ChevyTahoePPVandRetailmodels
(WorkswithOEM“MyTouch”display‐storagepocket)



  
C‐DMM‐3003_INST_7‐18 

C‐DMM‐3003assembly
CM009403
Passengersidemountingbracket
CM009402
Driversidemountingbracket
10‐32Kepsnut
GSM30028
GSM33118
10‐32x1/2"Machinescrew
CM009068
VESAswiveladaptor
CM008582
PVCspacerwasher
CM86600
Nylonwasher
GSM31005
Flatwasher
GSM30016
N
y
locknut



  
C‐DMM‐3003_INST_7‐18 


OEMDashPriortoinstallation

Pullbackthedriversidelowerdashpaneltogain
accessandremovesidetrimscrew(7mmsocket)
Pulllowerdashpaneltowardsyoutoremove.

Removedriversideupperdashpanel.

Insertaflatbladepanelremovaltoolandremove
thepanelabovetheglovebox.
Removerubbercoverinloweraccessorypocketto
gainaccessandremovetwo(2)lowerdashpanel
screws.
(
7mmsocket
)




  
C‐DMM‐3003_INST_7‐18 


Carefullyremove(unsnap)centertrimbezelaroundtouch
screenandclimatecontrols
Removethree(3)screwsfromtheventhousingandremove
thehousing.Repeatforpassengerside.(7mmsocket)
Removetwo(2)screwsoneachsidenexttotheOEMscreen.
InstallsidesupportbracketsusingOEMhardware.
Looselyplacethecentertrimbezeluptothe
dashandmarktheplasticareaaroundtheupper
sidebracketstobenotched.
Carefullynotchtrimbezelaccordinglyandreinstallback
intodash.Re‐installallventsanddashtrim.
FileorDremeltoolworkswellfornotchingplastic.
Onthe2017andolderTahoe,(2)plastictabswillneedtobe
trimmed.Thiscanbedonewithasimplesnipfromapairof
diagonalcutpliers
OEMTrimBezel
P/N:22883557



  
C‐DMM‐3003_INST_7‐18 



Re‐installalltrimanddashpanels.Ithelpstoraise
thescreentosnapinthetrimaroundthedash.
AttachtheC‐DMM‐3003using(4)10‐32x1/2"screws
and#10Kepsnuts.
Determinedesiredpositionforyourspecificcomputer
andattachtoDMMswivelplateusingnylonwashers,
steelwashers,andnylocknuts.Tightensothatthedock
rotatessmoothly.(Firm,butnottootight)
Runwiringasdesiredandtestequipment.
AttachVESAswivelplatetothebackofthemounting
bracket.Thegraynylonwasherwillgobetweenthis
bracketandtheDMMswivelplate.
Installationisnowcomplete