Havis C-DMM-3004 User manual

C-DMM-3004_INST_4-20
INSTALLATION INSTRUCTIONS
C-DMM-3004 Flip up Dash Monitor Mount
2014-2020 Dodge Durango
TOOLS REQUIRED:
Ratchet Wrench Dash panel removal tool Open End Wrench - 7/16”
Socket Set Phillips screwdriver
Always!
 Read all instructions before installing any Havis, Inc. products.
 Check for obstructions (Wires, brake lines, fuel tank, etc.) before drilling any holes!
 Use hardware provided with install kit
HARDWARE and PARTS:
QTY DESCRIPTION PART#
2 Upper support bracket CM009333
2 Side support bracket CM009334
4 10-32 x 1/2" Machine screw GSM33118
4 #10 Flat washer GSM31003
2 10-32 Keps nut GSM30028
1 VESA rotator plate CM010471
2 1/4" x 3/4" Carriage bolts GSM32000
1 PVC washer (2.875” diameter) CM010648
2 1/4" Plastic washer CM86600
2 1/4" Steel washer GSM31005
2 1/4" Nylock nut GSM30016-1
Notes:
The C-DMM-3000 swivel plate accepts C-MM-301 offset bracket used with C-MM-2XX adaptors.
C-MM-2XX series adaptor brackets are not needed for most VESA 75 and other Havis Docking Station
mounting applications.
CM010471 VESA rotator plate gives additional positioning options, but is not required depending on
mounting preference.

C-DMM-3004_INST_4-20
C-DMM-3004
Assembly CM009333
Upper support brackets GSM33118
10-32 x 1/2”
Machine screw
GSM31003
#10 Flat washer
GSM33118
10-32 x 1/2"
Machine screw
GSM31003
#10 Flat washer
CM009334
Side support bracket
GSM30028
10-32 Keps nut
CM010471
VESA rotator plate CM010648
PVC washer
CM86600
1/4" Plastic washer
GSM31005
1/4" Steel washer
GSM30016-1
1/4" Nylock nut
GSM32000 – 1/4"x
3/4"Carraige bolt

C-DMM-3004_INST_4-20
View of dash center instrument panel
Carefully r
einstall trim bezel
/ panel assembly
with
four
brackets protruding out of gap between bezel and dash.
Repeat process for lower side support brackets.
Brackets go behind the OEM screen mounts.
Carefully remove trim bezel / panel assembly
using plastic panel tool.
Remove (4) 7mm head fasteners around OEM
screen. Attach the upper support brackets behind
the OEM screen
mounts
and reinstall fasteners.
Remove trim panel and set aside.

C-DMM-3004_INST_4-20
Attach the DMM frame to the brackets using 10-32
x 1/2" screws and washers at the top and 10-32 x
1/2" screws, washers, and keps nuts on the side.
Installation is now complete.
Double check all hardware, latching and wire
harness clearance.
Position VESA plate on back of Device as desired.
Attach VESA plate with carriage bolts to the back
of the dock. The gray PVC washer will go between
this bracket and the DMM swivel plate.
Attach the dock to the mounting bracket
(
with hardware
supplied with dock) and run wires as desired.
Determine desired position for your specific computer
and attach to DMM swivel plate using 1/4"x 3/4” carriage
bolts, PVC spacer, nylon washers, steel washers, and
nylock nuts. Tighten so that the dock rotates smoothly.