Hawking Hawkvision HNC3W User manual
Quick Installation Guide
Model No. HNC3W
HawkvisionTM
Universal Smart
Camera
Package Contents
• 1x HNC3W HawkVision Universal Smart Cam
• 1x Power Adapter 5V/1.2A
• 1x Camera Stand/Mounting Kit
• 1x Three foot Ethernet Cable
• 1x Setup CD-ROM
• 1x Quick Installation Guide (QIG)
System Requirements
• Windows XP or later with an available CD/DVD-Rom Drive
(only required for initial setup)
• A LAN Port on your network (only required for initial setup)
• Wireless 802.11b/g/n network (only if you wish to connect
to your network wirelessly.)
• Power Outlet
• Computer Platform for viewing: Windows XP or later, Mac
OS 10.4 or later
CPU: Intel Pentium III 800MHz or above
RAM: 512MB
Resolution: 800x600 or above
Interface: Internet Explorer 6.0+, Firefox 2.0+, Safari
2.0+, or Chrome
• SmartPhone/Tablet Interface (optional): iOS or Android
EagleSense App
IR (Infrared) Lights
Turns on when camera is in Low Light/Night Vision Mode
Internal Microphone
Allows the camera to receive sound/voice
Camera Lens
WPS (Wi-Fi Protected Setup) Button
Press and release to initiate easy wireless connection with WPS devices
Power Plug (5V/1.2A)
Plug the provided AC adapter to power on the device.
Camera Mount
Hole to connect to the camera stand.
LAN Port
Used to connect the camera via Ethernet cable.
Installing the Camera Stand
The camera comes with a camera stand, which uses a swivel ball screw head
to lock to the camera’s back mount. When the camera stand is attached, you
can place the camera anywhere by mounting the camera through the three
screw holes on the base of the camera stand.
Connecting the Camera to the Network
Use the provided Ethernet cable to connect the camera to your local area network
(LAN). Connect the AC power adapter to the camera and it will be powered on
automatically. You can verify the status from the Power LED on the front panel of
the camera. Once connected, the LINK LED will also flash a green light,
indicating that the camera is ready for use.
PRE-CONFIGURATION
Hardware Setup
PRODUCT DESCRIPTION
Power
LED is on, when the power adapter is connected and plugged into an outlet
Link LED
Indicates the camera’s network connectivity with flashing green light
Reset Button
Press and release to reboot the camera. Press and hold for more than
5 seconds to perform a factory reset.
Ethernet
DC 5V
WPS Reset
4) Congratulations. Your are done configuring the camera.
Now, you can start viewing the camera images, using any
computer on your local area network. If you wish to use the
camera wirelessly, please continue with the wireless
setup.
On the web browser, click on Setup. On the setup page, on
the left column, click on Network, then select Wireless.
On the wireless settings page, click on “Site Survey”. Wait a few
seconds, and a list of networks will appear. Double click on your
wireless network. It should be highlighted. Once that is done, the
Network ID should change to your selected network.
Note: if you have a secured wireless network, you must choose
your Authentication type. In the drop down box, select your
security type and then be sure to type in the wireless key/password
of your wireless network.
Click “Apply.” The device will then reboot. You may now remove the
Ethernet cable and go wireless. Now, you can start viewing the
camera images, using any computer on your local area network.
!The camera must be connected to your local area network with an
Ethernet cable for the initial setup. Once connected, wait until the
LINK LED flashes green, then the camera is ready for installation.
1) Insert the Setup CD into your Computer’s CD-Rom and
wait for it to autoload. Once the program starts, select
“IPFinder”. Note: the initial camera setup requires a
Windows computer. Once setup, any Operating System will
be able to access the camera’s image via a web browser.
2) Once IPFinder starts, it will automatically find the
camera. The IP address and Mac Address will be listed on
the IPFinder. Make sure the MAC address matches the
one on your device. Select your camera and click “Link”.
Important: please make note of this IP Address. You will
need this to access the camera from a different computer.
3) After you press “Link”, your web browser will prompt you to
enter in a username/password.
Default Username: admin Default Password: admin
Note: Some web browsers will prompt you to install an
add-on, you must allow this to properly configure the device.
Thanks for choosing Hawking Technologies, Inc.!
Technical Support Information
Website: www.hawkingtech.com
Phone: 1.888.202.3344
E-mail: T[email protected]
©2012 Hawking Technologies, Inc. All rights reserved. All trademarks herein are the property of
their respective owners. IOS is a trademark or registered trademark of Cisco in the U.S. and
other countries. Android is a trademark of Google Inc. No affiliations are implied or expressed.
CAMERA SETUP
WIRELESS SETUP
SET UP
From your computer, access “http://www.c4mi.com” in your
web browser. Select “User Login”in the top right hand
corner of the window to create your account.
Locate the unique 16 character
alpha-digital “activation code” located
on the back of your product. Use this
code to activate cloud service to view
the camera image from the web or
portable devices.
ACCESS
Once you have created an account on C4mi.com, you can
access your camera from any computer by logging into your
account via C4mi.com. To access your camera from your iOS
and Android devices, simply download the “EagleSense” app
on your chosen device and login with your C4mi.com account.
Please enter the
activation code when
prompted by
C4mi.com. After you
have successfully
created an account,
make note of your
chosen username and
password since you
will need this to access
your device in the
future.
INTERNET VIEW
Other Hawking Digital Camera manuals
