Hayman FV137C User manual

WARRANTY
GUARANTEE
FlameVault
Safe Operation Guide
ONE YEAR WARRANTY
All Hayman Safe Companyproducts carry a warranty to the original retail purchaser
to be free from defects in material and workmanship. Standard models are
warranted for ONE (1) year from the original date of purchase.
This warranty applies only to new safes purchased from Hayman Safe Company or
its authorized dealers. Proof of purchase must be provided so as to establish date of
purchase and supplying dealer.
Hayman Safe Company will, at our option, repair or replace any defective part or
unit.
Authorization must be received from Hayman Safe Company prior to
performance of any service which will be submitted under warranty.
Improper installation, improper use, lack of proper maintenance or accidental
damage will nullify this warranty. No other warranty, expressed or implied, is
offered. This warranty cannot be changed, modified, enlarged or altered without
direct written consent from Hayman Safe Company.
Hayman Safe Company is not responsible for consequential damage, incidental
expenses or personal injury.
This warranty gives you specific legal rights.
You may have other rights which vary from state to state.
(1) HR. FlameVaults
Key Features:
·Removable Drawer
·Tri -spoke Handle with Combo
lock.
·Electronic Lock Available in All
Sizes
·Bolt Down Hole Provided.
(
2
) HR. FlameVaults
Key Features:
·Key locking Drawer (275E,
288E, 2100E & 2120E)
·Auto Locking Door Detent
·Electronic or Combination
Lock Available in Certain Sizes
·
Bolt Down Hole P
rovided.
FIRE PROTECTION
Hayman Safe Companywill, at our option, replace or repair any FlameVault if its
contents are ever damaged by fire.
To claim this guarantee, ship the fire damaged safe and a copy of the fire department
report to us.
We will repair or replace the safe and return it to you.
Improper installation can nullify this guarantee.
HAYMAN SAFE COMPANY
1291 N SR 426 Oviedo, FL 32765 www.HaymanSafe.com

1 Hour FlameVault (FV132C, FV137C, FV151C)
Mechanical Safe Lock Operating Instructions:
1. Turn the dial clockwise (to the right) until the first number of your
combination aligns with the opening index 4 times, be sure to stop on
the first number of your combination the fourth time.
2. Turn the dial counterclockwise (to the Left) until the second number of
your combination aligns with the opening index 3 times, be sure to stop
on the second number of your combination the third time.
3. Turn the dial clockwise (to the right) until the third number of your
combination aligns with the opening index 2 times, be sure to stop on
the third number of your combination the second time.
4. Turn the dial counterclockwise (to the left) until the fourth number of
your combination aligns with the opening index, be sure to stop on the
fourth number of your combination the first time it aligns.
5. Turn the tri-spoke handle to the right to gain access to the safe.
6. Locking your safe; Turn the tri-spoke handle to the left engaging the
boltwork and then spin the safe dial to the right at least 4 full turns.
If you do not successfully gain access repeat steps 1-5.
2 Hour FlameVault (FV261C, FV275C)
Mechanical Safe Lock Operating Instructions:
1. Turn the dial counterclockwise (to the left) until the first number of your
combination aligns with the 12 o’clock opening index 4 times, be sure to
stop on the first number of your combination the fourth time.
2. Turn the dial clockwise (to the right) until the second number of your
combination aligns with the 12 o’clock opening index 3 times, be sure to
stop on the second number of your combination the third time.
3. Turn the dial counterclockwise (to the left) until the third number of
your combination aligns with the 12 o’clock opening index 2 times, be
sure to stop on the third number of your combination the second time.
4. Turn the dial clockwise (to the right) until the dial comes to a complete
stop, and then turn the safe handle to gain access.
5. Locking your safe; Close the safe door and then spin the safe dial to the
left at least 4 full turns.
If you do not successfully gain access repeat steps 1-4.
Key lock: You can use the key lock to lock the safe. In order to unlock
the safe using only the key, the safe combination has to be dialed and
left in the open/unlocked position.
1 & 2 Hour FlameVault
Electronic Safe Lock Operating Instructions:
To open your safe using your master code:
·Push *, then your code (factory set to 1 2 3 4 5 6), followed by #.
·Turn handle to open the safe. The lock will timeout and not function for 3
minutes after 3 wrong codes are entered.
To change your master code:
·Locate the access hole on the inside back of your door. Inside the hole is a
button.
·Press the button, then enter your new code (4 to 8 digits long), then press
#. New code is set.
·Test your new code several times while the door is open.
To add new users (up to 4 additional):
·Push *, #, your master code, #. You are now in programming mode.
·Press 1 to indicate that you want to add a user, followed by the user
number (2, 3, 4, or 5) you want to add.
·Enter the new code (4 to 8 digits long), followed by #.
·Enter the new code again, followed by #.
·Test your new code several times while the door is open.
To delete a user:
·Push *, #, your master code, #. You are now in programming mode.
·Press 2 to indicate that you want to delete a user, followed by the user
number (2, 3, 4, or 5) you want to delete, then press 1.
To toggle the input display on & off:
·Push *, #, your master code, #. You are now in programming mode.
·Press 7 to toggle the display on and off.
Bolt Down Instructions:
Steps:
1. Place the safe in the location desired.
Note that it is desirable to have at least 1”clearance to the wall on the back and sides.
2. Mark the floor at the two front corners of the safe.
This will help in relocating the safe after drilling the mount holes in the floor.
3. From inside the safe, mark the floor through the mount holes in the bottom of the safe.
4. Move the safe to the side and drill the floor at the marks with themasonry drill bit.
Be sure to drill the holes deeper than the length of the anchors.
5. Vacuum the concrete dust out of and from around the holes in the floor.
6. Move the safe back into position using the corner marks to help align the safe.
7. Insert the anchor through the safe floor and into the concrete floor until the washer
touches the safe floor, and then tighten the nuts from inside the safe.
8. Tighten first to a barely snug level on each bolt before tighteningup all bolts evenly.
Tools You
Will Need:
·Drill Motor
·Anchors
·Masonry Drill Bit
·Wrench to fit nuts on anchors
·
Marker to mark the floor