HDanywhere MHUB PRO (8X8) 70 User manual

QUICK START GUIDE
FULL MANUAL ON HDANYWHERE.COM/SUPPORT
1Connect a HDMI source device (e.g Satellite/Cable TV, Apple TV, Blu-ray, DVD
etc) to one of the ports labelled “SOURCE INPUT” on the MHUB chassis using a
good quality HDMI cable.
The steps below describe how to connect a single HDMI source to a display location for outputs A-H and enable remote control (IR) signals to be sent from that location back to your
MHUB chassis. Repeat the steps below as necessary for each source or display.
2Connect a CAT cable between one of the HDBASET output ports (labelled A-H)
on the MHUB chassis, and the “HDBASET” port on the MHUB receiver, power on
the matrix via the included IEC cable.
3
Connect a HDMI cable between the port labelled “HDMI OUT” on the
MHUB receiver and a HDMI port on your display. Ensure that your
display is switched to the correct input. Note: MHUB receivers do not
need any power cables to work, power is delivered from the MHUB
chassis. Check the white LED light on the MHUB receiver is lit, this
indicates a connection with the MHUB chassis. Check that you are
receiving a picture on the connected display.
4
6
5
To control your HDMI source from your display location, connect an IR TX to the
“SOURCE IR (OUT)” port on the MHUB chassis, that matches the “SOURCE
INPUT” port number for the source you want to control. Connect an IR RX to the
“IR (IN)” port on the MHUB receiver.
Test the IR control is working by using the source device remote pointed
towards the IR receiver at your display location.
To complete the installation, connect the MHUB “IP” port to your router via an
ethernet cable and follow the information on the attached ‘Next Steps’ sheet.
HDMI CABLE
CAT6 CABLE
INFRARED (IR) CABLE
NETWORK CABLE
POWER
1
6
23
4
5
CAT6 RESOLUTION/DISTANCE GUIDE HD
0m
0ft 10m 32ft 20m 65ft 30m 98ft 40m
131ft 50m 164ft 60m 197ft 70m 230ft 80m 262ft 90m 295ft 100m 328ft
UHD
1 2
3 4
1x IEC POWER CABLE
1x MHUB PRO (8X8) 70 CHASSIS
8x MHUB PRO (8X8) 70 RECEIVERS + 16x MOUNTING WINGS 1x CONTEXTUAL & 1x MASTER REMOTEINFRARED (IR) CABLE2x CHASSIS MOUNTING WINGS
10x IR RX
17x IR TX
IN THE BOX
5 6
7 8
OK
E
1234 5 678FG H
OK
E
1234 5 678FG H
PRO
MHUB

MHUB PRO (8X8) 70 CHASSIS (REAR)
13
4
14 15
16
138
5 6 7
11 129 10
2
PORTS & LABELS
FULL MANUAL ON HDANYWHERE.COM/SUPPORT
“SOURCE INPUTS” [1-8]: Use to connect HDMI source
devices to the MHUB matrix
“HDBASET” Outputs [A-H]: Connect your MHUB
receivers to these ports via a CAT cable
“HDMI” Outputs [A-H]: These ports provide a mirror of
the corresponding HDBASET output
“LAN” Port: If you wish to enable the ethernet ports on
your MHUB 4K Pro receivers, then connect your router
to this port via an ethernet cable
Receiver RS232 port: See manual
“DIGITAL” audio port: Use this port to extract
multi-channel audio via a coaxial cable
“STEREO” audio port: Use this port to extract
down-mixed stereo audio via a 3.5mm jack cable
Earthing Point: Use to earth your MHUB
“HUB IR (IN)”: Connect an IR RX to this port to control
your MHUB with the included IR remote control (or other
learning remote) whilst in line-of-sight of the IR RX. Or
control the MHUB with a third party controller via direct
IR, using the optional add-on accessory called the
‘MHUB IR integration cable’. (1.55.911.001.1)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
“DISPLAY IR (IN)” [1-8]: Connect IR RXs to these ports
to control your displays via IR with a third party control
system
“ALL IR (IN)”: Connect an IR RX to this port to send
commands to all displays simultaneously
“SOURCE IR (OUT)” [1-8]: Connect IR TXs to these ports
to control your source devices via IR. The “SOURCE IR”
port number corresponds with the source input number
“AMP IR (OUT)”: If you have an AVR in your system,
connect an IR TX to this port and place it on the IR
window of your AVR
“HUB CONTROL IP” Port: Connect the MHUB system to
your router via this port to enable controllability via
TCP/IP commands, web GUI access and system
control via the uControl App
“HUB CONTROL RS232” Port: Use to integrate your
MHUB with a control system via RS232
AC input: Connect the supplied IEC lead to this port to
provide power to your MHUB
MHUB PRO logo ON/OFF: Press and hold for 2
seconds to turn MHUB matrix on or off
Source Selector (1-8): Select which source you
want to switch to, followed by display A-H
LCD Panel: Displays MHUB system information and
routing status
Display Selector (A-H): Select which display you
want to ouput to
Menu and Navigation Control: Brings up EDID, IP
and other menu settings
1
2
Optional DC input: Plug a 24V / 1A DC power supply
into the unit if you are not using PoH
HDBASET: Connects back to the HDBASET output
on the MHUB chassis
3
4
5
6
7
“IR IN”: Connect an IR RX to the ‘IR (IN)” port to send IR
commands back to the MHUB chassis
“IR OUT”: Connect an IR TX to enable control of your display
“HDMI OUT”: Connect this to your local display using a HDMI
cable
RS232 Port: See manual
Dual Ethernet Ports: Connect ethernet cables to these ports
to provide a wired ethernet connection to local devices
MHUB PRO (8X8) 70 CHASSIS (REAR ) MHUB PRO (8X8) 70 TOUCH PANEL (FRONT)
MHUB PRO (8X8) 70 RECEIVER
MHUB PRO (8X8) 70 TOUCH PANEL (FRONT)
12345 6
12 3 456
7 8
78
A
A B C d E F G H
Display IR (IN)
HUB IR (IN) source ir (OUT) AMP ir (OUT)
HUB CONTROL
RS232
IP
100-240V AC 50/60HZ
SOURCE INPUT
RS232
DigitaL Stereo
B
RS232
DigitaL Stereo
C
RS232
DigitaL Stereo
D
RS232
DigitaL Stereo
E
RS232
DigitaL Stereo
F
RS232
DigitaL Stereo
G
RS232
DigitaL Stereo
H
RS232
DigitaL Stereo
LAN
ALL ir (IN)
ABC D E F G H
45
12 / 3
MHUB PRO (8X8) 70 RECEIVER
IN OUT
1 2 3 4 5 67
OK
E
1234 5 678FG H
PRO
MHUB