HeBao DAS-102T User manual

The Visionary Future of Digital Reality
DVI Product Series
User Manual
Single-Port Cat-X DVI-D Transmitter: DAS-102T
Single-Port Cat-X DVI-D Transceiver: DAS-102TR
DVI Cat-X Distribution System

2| HeBao Technology
www.hbdepot.com | 2
www.hbdepot.com |
3
Product Introduction
e DVI Cat-X Distribution System includes a Transmitter and one or more Transceivers.e system uses Cat5/5e/6 cable to
extend DVI-D signals. With its cascading capability you can extend your digital video displays further. DVI Cat-X Distribu-
tion System can save on budget by using low-cost Cat5/5e/6 FTP cable. e Transmitter and Transceiver units are tted with
a magnetic pad enabling them to be easily attached to any metal surfaces. A screw xing plate is also included for permanent
installation. e DVI Cat-X Distribution System is perfect for Digital Signage applications where vivid, high-resolution digital
video can to be shown without distance limitations at reduced costs.
Product Features
♦Equipped with DVI local connection for Transmitter to extend DVI signal over Cat5/5e/6 FTP cable
♦Built-in Cascading function one DVI output port for Transceiver to extend DVI signal over Cat5/5e/6 FTP cable
♦1.65GHz Video Amplier Bandwidth
♦DVI Input/Output Connector: DVI-D digital video signal (Digital only. DVI-I and DVI-A not supported)
♦EQ control to adjust the video quality
♦LED status to indicate DVI activity
♦Magnetic pad and attachable metal plate on each device to simplify installation
Panel Descriptions
♦DAS-102T Single-Port Cat-X DVI-D Transmitter
Front Panel & Rear Panel
1. Video EQ Control
2. Power Jack
3. RJ-45 DVI Output
4. EQ Indicator LED ON : Auto EQ LED Off : Manual
5. Link Indicator of Local Monitor (MI)
6. DVI Output for Local Monitor (MI)
7. DVI Input (Use HDMI connector)
8. RJ-45 DVI Input
9. Link Indicator
10. Power Indicator
♦DAS-102TR Single-Port Cat-X DVI-D Transceiver
♦DVI-HDMI Cable for Player
➊
➊
➊
➊
➋
➋
➌
➌
➍
➍➒
➎
➎➓
➏
➏
➐
➑
To DVI Player
To HDMI Input of Transmitter

4| HeBao Technology
www.hbdepot.com | 4
www.hbdepot.com |
5
Skew represents the dierence in propagation delay between the fastest and slowest set of wire pairs. A lower skew will mean
a longer video transmitting distance.
♦e maximum distance that supports cascading function for 720p & 1080i resolution is at 70 m. e maximum distance
without cascading function for 1080p resolution is at 30 m. However, with the use of Cat 6 HBT Cable, the max distance
for 1080p resolution can reach up to 60 m.
♦e FTP type of Cat5/5e/6 cable is recommended for some installations that might have the potential interference. e
RJ-45 terminations to the Cat5/5e/6 cable must be made to the EIA 568B specications. (See gure below)
♦Plug one end of the cable to the Transmitter’s “LINK IN/OUT” port and the other end to the Transceiver’s RJ-45 “LINK
IN/OUT” port. e monitor connected to the Transceiver should now display and the “LINK” LED should turn green to
indicate the DVI signal activation. Adjust the “EQ”control for best quality DVI display.
4. Extend Audio Signal:
e DAS-102T Transmitter and DAS-102TR Transceiver are not able to extend audio signals. Use a pair of DAS-AR Audio
Extenders with 4-wire phone cable and RJ-11 connectors to extend the audio.
5. Cascading additional Transceivers and Displays:
♦Cascading additional Transceivers to remote DVI-D displays is possible by using additional DAS-102TR Transceivers
and Cat5/5e/6 cable. Proper power grounding is a must for large group system cascading in order to prevent unpredicted
interferences
♦A DVI-D splitter or distribution amplier may be applied at each DVI-D output to broadcast additional local DVI-D
displays.
Installation and Operation
1. Install DAS-102T Transmitter :
♦First Time Set-up: Turn o the DVI output device (PC or DVD Player) and monitors.
♦Device Connection: Connect local DVI monitor (M1) to the “DVI/M1 OUT” of the transmitter and take the DVI-
HDMI cable, plug HDMI end to “INPUT” port of transmitter and the other end of the cable to PC/Player’s DVI-D video
port.
♦Connect the power adaptor to the “5VDC” and plug into the power outlet.
♦System Turn On: Turn on your DVI output device and monitor to conrm the functionality of the display. e “M1 LINK”
LED of the Transmitter should display orange to conrm the connection of a local DVI monitor.
♦Remote monitors: Make sure the remote monitor(s) to be connected to the DAS-102TR Transceiver can display the
broadcast video resolution.
♦EQ Adjustment: In most of the cases, you can adjust the EQ control to Auto mode by rotating the EQ control anti-
clockwise. e “EQ” and ”Auto”LEDs will display blue. If noise or an unstable image is seen on the local DVI monitor it
indicates the DVI signal received by the Transmitter needs to be adjusted. Adjust the EQ control for best image display
quality. e “EQ”and ”Auto” LEDs will turn o to indicate manual EQ mode.
♦EDID Simulation: e transmitter has built in an EDID simulator. When a local DVI monitor is connected to transmit-
ter it will automatically record the EDID data from the DVI monitor.When a local DVI monitor is not connected the
transmitter, it will simulate the EDID data and activate the DVI signal at the PC/player.
2. Install DAS-102TR Transceiver :
♦Connect DVI cable of DVI monitor to the receiver and turn on the monitor.
♦Plug power adaptor to DAS-102TR. At this time the “PWR” LED and “M1 LINK” should be on and the other “LINK”
LED should be o since there is no video signal input from “LINK IN” port.
♦If you see some dots or unclear image on the DVI monitor, the DVI signal received by Transmitter need to be adjusted. To
adjust image display to Auto mode, rotate the EQ to the left side.e “EQ” and “Auto” LEDs will display blue. Or you can
adjust the EQ control using the manual mode, the “EQ” and “Auto”LED will turn o to indicate the manual EQ mode.
3. Cat5/5e/6 Cable Connection:
♦Most makes and versions of current Cat5/5e/6 cables will work with the DAS-102T Transmitter and DAS-102TR Trans-
ceivers. However since the quality and characteristics of Cat5/5e/6 cable varies it has been found that some perform better
than others, even if they cost lower.e major factor inuencing the transmitting distance is the skew property of the cables.
DVI-D Transmitter
DVI to HDMI Cable
PDP LCD / TV Projector
DVI Projector and Monitor
PDP LCD / TV Projector
DVI Projector and Monitor
DVI-D Transceiver
DVI-D Transceiver DVI-D Transmitter
Cat-x Cable DVI to HDMI Cable
HDMI Player
HDMI Player
DVI-D Transceiver
DVI-D Transceiver DVI-D Transmitter
HDMI Player
Cat-x CableCat-x CableCat-x Cable DVI to HDMI Cable
1 2 3 4 5 6 7 8
JACK POSITION
PAIR 1PAIR 2 PAIR 4
PAIR 3
The EIA/TIA definition of 568B in the pin assignment
1. Orange White 2. Orange 3. Green White 4. Blue
5. Blue White 6. Green 7. Brown White 8. Brown
PDP LCD / TV Projector
DVI Projector and Monitor
PDP LCD / TV Projector
DVI Projector and Monitor
PDP LCD / TV Projector
DVI Projector and Monitor
PDP LCD / TV Projector
DVI Projector and Monitor
PDP LCD / TV Projector
DVI Projector and Monitor

6| HeBao Technology
www.hbdepot.com | 6
www.hbdepot.com |
7
Specications
Remarks
1. Please read this operation manual carefully before installing the system.
2. Please use high quality Cat-X cable for optimum results.
3. To prevent potential power damage do not use 2-wire extension cords. Ensure DC outlets at PCs and displays are on the
same phase and have correct and common grounding.
4. Limited Warranty:
• In no events shall the vendor’s liability for direct or indirect, special, incidental or consequential damages, loss of prot,
loss of business, or nancial loss which hay be caused by the use of the product exceeds the price paid for the product.
• e vendor makes no warranty or representation, expressed or implied with respect to the contents or use of this docu-
mentation, and especially disclaims its quality, performance, merchantability, or tness for any particular purpose.
• e vendor also reserves the right to revise or update the product or documentation without obligation to notify any
user of such revisions or updates. For further information please contact your vendor.
Notice
1. All other company or product names mentioned herein are trademarks or registered trademarks of their respective
companies.
2. Specications are subject to change without notice.
3. Please read user manual carefully before operating the device
4. Please use the power adaptor accompanied with this product. Warranty does not cover for damages caused by pairing
other power adaptor
5. Please check all connecting devices are properly grounded to avoid electric failure
6. is product has limited warranty for one year from defects in material and workmanship. Items that are physically dam-
aged, misused, tempered with or altered are void of warranty. For further details please contact your distributor. In case
warranty sticker is damaged or missing, warranty is void. For further details please contact your distributor.
Model / Order No. DAS-102T DAS-102TR
Model Name Single-Port Cat-X DVI-D Transmitter Single-Port Cat-X DVI-D Transceiver
Input HDMI & DVI Female x 1 RJ45 x 1
Output RJ45 x 1 & DVI Female x 1
Image Control EQ x 1
Signal Display DVI-D
Casing Metal
Resolution at Max Distance 720p / 1080i at 70m (support cascading function) ;
1080p at 30m (without cascading function)
Power Adaptor DC 5V, 2000mA
Dimension (L x W x H in mm) 62x113x29 62x113x29
Operating Temp. 0° C ~60° C
Storage Temp. 0° C ~60° C
Humidity 25%~70% Non-Condensing

8| HeBao Technology www.hbdepot.com | 8
HeBao Technology
No. 35, LN 32, GuanFu S.RD., SongShan District, Taipei City, Taiwan
Tel:[phone]
Fax: [phone]
www.hbdepot.com