HELIX Competition RS 6.3 User manual

High End 3-Way Component System
Made in Germany
BEDIENUNGSANLEITUNG
INSTRUCTION MANUAL

5
Dear Customer,
congratulations for your purchase of this high-quality HELIX
speaker system made in Germany.
The RS6.3 Competition high end 3-way-system was develo-
ped and designed with state-of-the-art technology for perfect
music reproduction in vehicles.
To achieve the optimum stereo effect and tonal balance fol-
low the tips and instructions of this manual.
AUDIOTEC FISCHER wishes you many hours of enjoyment
with your RS6.3 Competition.
General installation instructions
Please use these instructions to find the best possible acou-
stic position for the chassis in the vehicle.
The tweeter and the midrange should be installed as close as
possible to each other. Best locations can be found in the
dash board or in the A-pillar. The chassis should be positio-
ned as far away as possible from the driver and between
chest- and eye level.
We strongly recommend to align the chassis on axis so that
they play into the same direction.
It’s surely a question of taste whether to direct the chassis
directly towards the ear or against the windshield. The direct
ear position is slightly louder, and allows improved stage
focus. The indirect position is slightly faint but increases the
depth of stage. The optimum alignment of the chassis com-
bines both advantages and leads to perfect staging.
Unfortuna
tely there are little chances to find this ideal instal-
lation prerequisite in vehicles on the market.
Individual door panels and A-pillar covers for your vehicle
however provide speaker openings that make an optimum
positioning possible. Please ask your authorized dealer.
The RS806 mid/bass speaker should be installed in the door
with a slightly upward position. It is necessary that the associa-
ted area (metal, door panels and mounting rings) is prepared
with damping material (e.g. BRAX eXvibration) in order to pro-
duce a clean and tight kick bass response. Even in case that two
mid/bass speakers on each side are installed (e.g. a custom
made door panel) sufficient damping is strongly recommended.
Your HELIX RS6.3 Competition component system:
2 x RS806 Competition
16,5 cm high end mid/bass
speaker
2 x S802 Competition
54 mm high end mid speaker
2 x S801 Competition
25 mm high end tweeter
2 x RS6.3 Competition
3-way crossover
ø166
ø156
ø96
ø142
31
67
71
ø85
ø78
19
2640
ø49
ø32
ø58
ø46
25,7
18
9
ENGLISH
Measures in mm

The speakers of the system can be adjusted to your individual
listening habits by repositioning the jumpers.
Please make sure to turn off the entire system before
changing the jumper positions.
Function of jumper J1:
4- or 2 ohms mode
Jumper J1 adjusts the crossover to the so called 4- or 2
ohms mode. The basic adjustment (ex works) is the 4 ohms
mode which means that only one pair of woofers is used in
the vehicle.
When using two additional RS806 Competition speakers as a
double bass system on each side, e.g. in custom made door
panels, the jumpers J1 must be removed and fixed into the
2 ohms position
(see fig. 1 and 2).
Function of jumper J2:
Mid level adjustment
Jumper J2 is used for the individual adjustment of the mid
level (adjustment of level in relation to the level of the bass
and the tweeter). In the 0 dB-position (ex works) the mid-
range plays at the same level as tweeter and woofer. This
should be basis of your fine tuning.
Depending on the placement of the chassis and your indivi-
dual listening habits the level of the midrange can be raised
or lowered by changing the position of jumper J2.
In case of placement in the dash or higher the level should be
lowered (-1,5 dB / -3 dB). In lower positions such as door- or
kick panels the level should rather stay at 0 dB or even be
raised to +3 dB.
4 ohms mode (ex works) 2 ohms mode
J 1 J 2 J 3 J 1 J 2 J 3
Function of jumper J3:
Tweeter level adjustment
Jumper J3 is used for the individual adjustment of the twee-
ter level (adjustment of level in relation to the bass and the
midrange). For functions and recommendations please refer
to the discription of the midrange jumper J2.
Please make sure that changes in the position of the
jumpers J1, J2 and J3 must always be made simulta-
neously for the right and the left channel on both cross-
overs.
Special note: Try to connect the midrange out of phase to the
crossovers as the resulting 180° phase shift may well impro-
ve the overall staging of your system.
Adjustment of the crossover
Fig. 1 Fig. 2
1 x RS806 per channel 2 x RS806 per channel
Mid level depending on jumper position Tweeter level depending on jumper position
6

7
Due to the high quality standard HELIX products achieved an excel-
lent international reputation. Therefore we grant a warranty period of
2 years.
The products are carefully checked and tested during the entire pro-
duction process. In the case of service note the following:
1) The 2 years warranty period commences with the purchase of
the product and is applicable only to the original buyer.
2) During the warranty period we will rectify any defects
due to faulty material or workmanship by replacing or repairing
the defective part at our decission.
Further claims, and in particular those for price reduction, can-
cellation of sale, compensation for damages or subsequential
damages, are excluded. The warranty period is not altered by
the fact that we have carried out warranty work.
3) Unauthorized tampering with the product will invalidate this war-
ranty.
4) Consult your authorized dealer first, if warranty service is needed .
Should it be necessary to return the product to the factory,
please insure that
a) the product is packed in original factory packing in
good condition
b) the product is shipped prepaid, i.e. at your expense and risk
c) the receipt/invoice as proof of purchase is enclosed
5) Excluded from the warranty are:
a) Shipping damages, either readily apparent or concea-
led (claims for such damages must be immediately
notified to the forwarding agent).
b) Scratches in metal parts, front panels or covers etc.
This must be notified to your dealer within 5 days of purchase.
c) Defects caused by incorrect installation or connec-
tion, by operation errors, by overloading or by external force.
d) Products which have been repaired incorrectly or
modified or where the product has been opened by
other persons than us.
e) Consoquential damages to other equipments.
f) Reimbursement when repairing damages by third
parties without our previous permission.
WARRANTY REGULATIONTechnical specifications RS6.3 Competition
RS806 Competition high end mid/bass speaker
Power RMS 120 watts
Max. Power 150 watts
Impedance 4 ohms
DC resistance 3,6 ohms
VAS 12,1 liters
Sensitivity 90 dB
Resonance frequency 56 Hz
Frequency range 46 - 2500 Hz
External diameter x mounting depth 166 mm / 67 mm
S802 Competition high end mid speaker
Power RMS 30 watts
Max. Power 50 watts
Impedance 4 ohms
DC resistance 3,6 ohms
Sensitivity 90 dB
Resonance frequency 500 Hz
Frequency range 55 - 700 Hz
External diameter x mounting depth 85 mm / 19 mm
S801 Competition high end tweeter
Power RMS 120 watts
Max. Power 150 watts
Impedance 4 ohms
DC resistance 3,6 ohms
Resonance frequency 820 Hz
Frequency range 820 - 2500 Hz
External diameter 58 mm
RS6.3 Competition 3-way crossover
Crossover frequency 600 / 5000 Hz
Croosover slope 12 dB / oct.
Jumper functions J1 4-ohms or 2-ohms mode
J2 Mid level adjustment: +3 dB / 0 dB / -1,5 dB / -3 dB
J3 Tweeter level adjustment: +3 dB / 0 dB / -1,5 dB / -3 dB
Dimensions (H x W x D) 45 mm x 181 mm x 164 mm
No responsibility accepted for the accuracy of this information. Subject to technical alterations in the interest of progress.

AUDIOTEC FISCHER GmbH
Hünegräben 26
D- 57392 Schmallenberg
Tel.: + 49 29 72 97 88 0
Fax: [phone]
[e-mail]
www.audiotec-fischer.com