Henley Stoves Aurora 750 Service manual

Installation and
Operation Instructions
Aurora Electric Fire
CS 3SFPT 750 - Aurora 750 Electric Fire
CS 3SFPT 1100 - Aurora 1100 Electric Fire
CS 3SFPT 1300 - Aurora 1300 Electric Fire
CS 3SFPT 1400 - Aurora 1400 Electric Fire
CS 3SFPT 1500 - Aurora 1500 Electric Fire
CS 3SFPT 1800 - Aurora 1800 Electric Fire

1
TABLE OF CONTENTS
IMPORTANT INFORMATION .............................................. 2
UNPACKING ........................................................................ 3
OPTIONAL SIDE PANELS ......................................................... #
INSTALLATION AND LOCATION ............................................... #
PLACING THE LOGS AND EMBERS ........................................... #
PRODUCT INFORMATION ................................................. #
PRODUCT TECHNICAL INFORMATION ....................................... #
PRODUCT DIMENSIONS .......................................................... #
MANUFACTURERS INFORMATION ............................................ #
OPERATING THE FIRE ....................................................... #
MANUAL CONTROL ................................................................. #
REMOTE CONTROL ................................................................ #
WI-FI / SMART CONTROL ........................................................ #
MAINTENANCE INSTRUCTIONS ........................................ #
CLEANING ............................................................................. #
SAFETY FEATURES ................................................................ #
ENVIRONMENT .................................................................... #
WARRANTY ......................................................................... #
Please follow the installation instructions carefully
and then retain these instructions for future
reference.

2
Important information:
Keep the front of the fire at least 3 FEET AWAY from combustible materials.
These include but are not limited to: articles of clothing, curtains, cushions,
furniture, other soft furnishings and papers.
In order to avoid the product overheating please DO NOT cover the heater.
Always turn OFF and unplug the heater when it is not in use.
DO NOT use if the appliance or its cables are damaged.
NEVER place near bodies of water. These include but are not limited to:
bathtubs, fountains, ponds and other water containers.
NEVER allow any objects to enter or obscure any ventilation or exhaust
openings as this may result in an electrical shock, damage to the product or
may result in a FIRE.
A heater contains hot and/or sparking components inside, Therefore, DO NOT
use in areas where flammable gases, flammable liquids, paint and petrol are
used or stored.
AVOID the use of extension cables and timers to avoid FIRE.
This appliance IS NOT freestanding and should not be used as such.
ALWAYS use properly grounded fused and polarised outlets.
ALWAYS use ground fault protection where required by electrical codes.
To AVOID burns and/or personal injury NEVER touch any of the hot surfaces
such as the heater vent.
Power MUST BE DISCONNECTED before any cleaning, relocation or
maintenance.
Any replacement of circuitry or outlets should ONLY be performed by a
certified electrician.
To prevent a potential fire DO NOT attempt to burn any materials in the
heater. . These include but are not limited to: marshmallows, paper and wood.
DO NOT store or keep during transportation, outdoors or in a damp
environment.
NOT TO BE installed below an electrical socket outlet.
DO NOT leave children unsupervised whilst the appliance is switched on.
Please read the instructions carefully BEFORE installation.

3
1. Place the box on a flat surface. Make sure you have
enough space.
2. Remove any rings or bracelets which may scratch the
product or be damaged during removal.
3. Carefully remove the appliance from the box and put all
packing aside.
4. Please keep the original packing for further storage or
transportation.
5. Prior to installation, test the product to check that the
appliance is functioning correctly.
Keep plastic bags away from children and animals!
Use this product ONLY as described in this instruction manual.
Any other use is discouraged in order to prevent bodily harm
and/or fire.
Unpacking:
Congratulations on your new electric fire. In order to unpack
your product without causing any damage to yourself of the
product, please take care and follow the instructions.
Aurora Range

4
Optional Side Panels
When unpacked the fire has only one pane of glass visible at
the front. The two side sections are covered by blanking plates.
If the fire is to be installed as a two or three sided appliance
these plates need to be removed. To do this unscrew the fire
frame from the body of the fire, remove the panel and then refit
the fire frame.

5
Installation and location:
Connect the appliance to a single-phase AC supply of the
voltage specified on the ratings plate.
In the instance that the fire is connected directly to the mains
electricity supply, a fused switched spur with a 13 amp fuse
must be fitted.
The power supply must be able to handle 2000 watts
(2kw).
This appliance must be earthed
Do not use an extension lead or a timer.
Always ensure that all electrical work complies with the relevant
building regulations and the electrical code of practice.
This product is designed to be either wall mounted and / or
fitted and fixed inside a frame. This appliance has multiple
electrical components that must be kept away from water and
damp or moist conditions.
Please read the instructions carefully BEFORE installation.
The installation MUST be carried out by a qualified person.
Aurora Range

6
This product should be fitted to one of the following options:
1. Wall Mounted – Using the H bracket which is located on
the back of the appliance. It is important to use fixtures
that are appropriate for the type of wall. The wall must be
of sound construction and able to hold the weight of the
appliance.
2. Mounted on a solid base – Please keep a distance of at
least 5 cm from any non-combustible materials.
3. Fitted into a Studded Wall – Which needs to be finished
with either plasterboard or a plastered finish. The fire can
then be installed with the facing trim of the fire flush up to
the plastered finish. See Drawings below:

7
Make sure that the cable is not run across the heater and can
be plugged into the mains socket without the use of an
extension cable.
Please make sure that the plug socket outlet is in a location
that is easily accessible. The appliance should be switched off
when not in use and for maintenance.
Placing the logs and embers:
The accessory box which is packed inside the fire contains the
mixed black and white nuggets that create the fire bed. These
should be placed on the base of the fire in a random manner.
The logs are then placed in a position of your choice on top of
these. The logs are delicate and should be handled with care.
Aurora Range

8
Product information:
Product technical information:
Supplier name Henley Stoves
Model number CS 3SFPT 750
CS 3SFPT 1100
Voltage 220V – 240V AC50HZ
Fuse 13Amp
Nominal heat output 2.0KW
Minimum heat output 1.0KW
Maximum heat output 2.0KW
Manufacturers’ information:
Name Henley Stoves
Product Dimensions:
Height Width Depth
CS 3SFPT750 617 780 348
CS 3SFPT1100 617 1130 348
CS 3SFPT1300 617 1342 348
CS 3SFPT1400 617 1430 348
CS 3SFPT1500 617 1542 348
CS 3SFPT1800 617 1842 348
CS 3SFPT 1300
CS 3SFPT 1400
CS 3SFPT 1500
CS 3SFPT 1800

9
Operating the fire:
Manual control:
This appliance can be operated manually using the controls
situated on the top right hand side of the fire screen.
ON/OFF POWER SWITCH- This switch is used to turn the
mains supply to the appliance on or off. When the switch is in
the ON position an orange indicator light will show in the middle
of the screen. This needs to be in the on position for both
manual and remote operation.
STANDBY- Used to switch the appliance ON or OFF into
standby mode.
FLAME-Pressing this button will cycle through the four different
flame brightness levels.
HEATER- Use this button to select low heat, high heat or
heater off.
When low heat is selected the indicator light will glow orange.
When high heat is selected the indicator light will glow red.
Please note that the heater will only operate when the room
temperature is below the temperature on the handset, which
can be adjusted using the remote or through the app. When the
MODE HEATER FLAME STANDBY POWER SWITCH
Aurora Range

10
heater switches off the fan will continue to run to cool the
appliance.
MODE- Shuffle through a selection of pre-programmed effects.
Remote control:
Remove the battery / control panel cover by sliding
completely down and insert 2 x AAA batteries ensuring
the batteries are fitted correctly. Refit the cover by
sliding back up to the original position. Please ensure
old batteries are disposed of responsibly by contacting
your local authority about recycling schemes.
Ensure that the ON / OFF Power Switch on the fire is in
the ON position.
Point the remote-control handset directly towards the fire
and press the appropriate button to operate the fire.
Sliding the door down on the remote control will reveal
more buttons which offer additional functions. Otherwise
using the basic remote buttons will operate the fire in the
same way as the manual control buttons.
Setting the colour functions
Press lamp button:
1
2
3
Will change colour of flame, ash bed, ember separately.

11
Setting the Time
1. Press the clock setting button, which will start
the day cursor to blink. Using clock up and
clock down buttons set to the current day e.g.
Monday – 1, Tuesday – 2, Wednesday – 3 etc.
Press to confirm the required day.
2. The hour setting will now be blinking, adjust
using and to the desired hour and confirm
BATTERY
ADAPTIVE SENDING
FLAME
HEATING
TEMPERATURE
ROOM
TEMPERATURE
CLOCK STANDBY
ON/OFF
BRIGHTNESS SETTING
HEAT
TEMPERATURE UP
MODE ADAP
ADAPTIVE
HEAT FLAME
C / F
TEMPERATURE DOWN
MODE ADAPTIVE
1 2 3
1
2
3
TEMPERATURE SCALE FLAME COLOUR
ASH BED COLOUR
EMBER COLOUR
CLOCK SETTING
CLOCK UP
CLOCK DOWN
Aurora Range

12
using .
3. The minute setting will now be blinking, adjust
using clock up and buttons to the desired minutes
and confirm using the clock setting button.
Adjusting the desired temperature
Whilst the fire is switched on, use temperature
up and down to set the desired room
temperature. A confirmation beep will be heard
from the fire. If the room is already warmer
than the temperature set then the heater will
switch off until the thermostatic sensor detects
a fall in temperature.
Adaptive Control
Adaptive control works in target temperature 25°C with
high heat.

13
1. Download the ‘Smart Life’ APP
The app is free on both Google play and the app store.
Please search ‘Smart Life – Smart Living’.
Download the app.
2. Open the Smart Life App, Register and Log in
Open the app and click the register button, unless you have an existing
account, then please log in with your existing details.
Input an email, the app will send a code in order to verify your email.
Once you have received the code, input the code and create your
password.
MODE HEATER FLAME STANDBY POWER SWITCH
Wi-Fi / Smart control:
Preparation
In order to prepare please check that your mobile phone is connected to your Wi-Fi
router. Plug your fire in to the wall. Switch the fire on at the wall socket. DO NOT
use the STANDBY button to turn on, use the power switch. You should see an
orange dot appear on the screen.
The buttons on the fire are as follows:
Aurora Range

14
3. Add your device
Please touch the ‘Add device’ button or
the ‘Add’ symbol to add your device.
4. Scan the QR code
Touch the ‘SCAN’ symbol.
Scan the below QR code.

15
5. Connecting to your Wi-Fi
Select your Wi-Fi network and input the
password of your Wi-Fi network.
6. Establishing a connection
Give a long press to the standby button for
around 3 seconds.
You should see a red light next to the
orange dot in the middle of the fire screen.
The red light should be blinking quickly on
the screen. Roughly 2 times per second.
When prompted, if the red light is blinking
rapidly, confirm that the indicator is
rapidly blinking by checking the circle and
then by pressing ‘Next’
MODE HEATER FLAME STANDBY POWER S
Aurora Range

16
7. Adding your device
Wait whilst the app adds the device. Please
keep the phone close to the device whilst the
device is syncing.
If it fails to sync Repeat steps 4,5 and 6
8. Your device has been added successfully.
Now your device has been successfully
added click on the device and you are ready
to start using your phone to control your fire.

17
1. To turn the fire on press the
standby button at the
bottom of the screen
2. To set timers press the
clock button at the bottom
left of the screen.
Along the top of the screen there are 5 tabs ‘Heat,
Flame, Ember,
Logs and Mode’
Heat- use this tab to control the temperature.
Flame- use this tab to control the colours of the flames.
Ember- use this tab to control the colours of the embers.
Logs- use this tab to control the colours of the Logs.
Mode- chose one of the preprogramed modes.
For the flame, ember and logs settings you can turn the default
Orange colour on / off by clicking the button and can add
additional colours by pressing the colour wheel and then selecting
your preferred colour from the big wheel above. Both the orange
button and the colour wheel button can be pushed on and off.
Using the App
Aurora Range

18
Maintenance:
You MUST remove the plug from the socket outlet and allow
the heater to cool completely before cleaning or maintenance.
Maintenance should only be carried out by a qualified person.
Cleaning:
A soft dry cloth, such as microfiber cloths, can be used to
remove dust and for general day to day care.
If a more thorough clean is needed a damp cloth, NOT WET,
may be used to wash the exterior surfaces. The glass can be
cleaned with glass cleaner and a soft cloth.
THE APPLIANCE MUST FULLY DRY BEFORE USING THE
HEATER.
Safety features:
As this appliance contains a heating component there is an
automatic thermal cut out safety feature. This feature stops the
product from overheating and from potentially causing a fire.
If the appliance reaches a temperature above the guideline
parameters the automatic thermal cut out safety feature will
activate and the heater will cut out. However, the fans will
continue to run in order to cool down the appliance.
Once sufficiently cooled the automatic thermal cut out safety
feature will automatically reset and the heater will be restarted.
If this problem continues, turn off the fire and disconnect from
the plug socket. Check that none of the ventilation vents are

19
WARNING!
The heater should NEVER be submerged in water.
The interior should NEVER be wet.
Cleaning chemicals such as but not limited to
detergents, alcohols and abrasives should NOT be
used.
Environment:
DO NOT throw out your appliance or its parts as municipal
waste. Contact your local government for advice on the
collection services and proper protocol in your area.
Please DO NOT dump your appliance as if not properly treated
hazardous substances can leak into water supplies effecting
animals and people’s health and wellbeing.
If you are replacing your old appliance, retailers are legally
obligated to dispose of your old appliance without any
additional cost.
obstructed. If your fire is connected to a chimney, the chimney
must be blocked off as the drafts can affect the appliance.
If the problem continues, keep the product unplugged from the
power socket and contact your supplier.
Aurora Range