HERA MOLELINE Series User manual

x
MOLELINE SERIES
Installation Guide
R
1 pcs.
Moleline®Series 1 pcs.
Moleline®Series Holder
1 pcs.
Allen Key
Packing Contents
• Mains power must be switched off before installing products.
• The connection, installation, commissioning and assembly operations of the products
must be performed by qualified technicians.
• Do not install wet, deformed or defective products and equipments,
do not provide power, please contact the nearest technical service.
• Install the products only in accordance with the connection patterns specified
in the relevant Specificiation Sheet.
• Do not open or attempt to repair the products and connection equipments.
• Do not open extra holes on products for mounting and protect products from impacts.
• Do not install the products except as described below.
• Different installation of products may cause products to malfunction or hazardous conditions.
• Use recommended mounting equipments for products.
• This product is not suitable for indoor use. Electric shock may pose a risk of fire or combustion.
• Please follow the steps below when installing the products
.
Installation
1
Installation Guide
Ground Construction
• All installation procedures, including installation of the products, should be carried out by authorized technicians.
• Installation of products in areas with constant fluid flow should be avoided.
• Do not engage in installation applications other than the installation method specified in the manual.
• Do not block the water drain channels in the products. Be careful during assembly.
• When creating the product holder well, consider the environmental infrastructure.
• Moleline Series is suitable for inground use when the conditions specified in the manual are created.
• Do not build Holder well on infrastructure like electricity, water, natural gas.

The ground will be ready when all the water mix to
artesian.
Gravel should be laid on the floor to prevent overflowing
and realize water discharge for holder area.
To test the water drain, place a some water should
be poured. 15 minutes should be waited to see
the water mixes with the artesian well.
MOLELINE SERIES
Installation Guide
R
2 3
4 5
15min
The concrete should be applied on sides of the hole
to fix product.

Before placing the product on the fixed Holder, the
product insertion screws must be tightened in the down
direction as shown in the figure. Do not place the product
without checking. Otherwise, the product will not sit, and
the elevator mechanism will be damaged if forced.
Place the product in its holder and press lightly.
The click sound will come when the product
is placed in the holder.
The holder should be installed to all prepared floor
drainage indicated in the figure.
MOLELINE SERIES
Installation Guide
R
6 7
8 9
Wait for the concrete is freezing. The holder should be
stayed remain and protected for external factors.

2+4 Pin Pushlock Type Connector
You must use Push Lock Type 2 + 4 Pin
Female Plug Cap for the last product of line
MOLELINE SERIES
Installation Guide
R
Connection
The two products should be 2mm at least.
• All installation procedures, including installation of the products, should be carried out by authorized technicians.
• Installation of product areas should be avoided in with constant fluid flow.
• Installation ground should be avoided on soft soil, clay, sand etc.
• Isolate cable and cable connectors.
• Do not engage in installation applications other than the installation method specified in the manual.
• Do not use on surfaces without forming the infrastructure of electrical and data cables.
• Do not drill any extra mounting holes in any area of the product.
• Do not block the water discharge channels in the products, be careful during installation.

MOLELINE SERIES
Installation Guide
R
1
2
Turn the screw in the up direction with the hex key
to remove the product from the holder
The product will rise up to a certain distance from the holder.
3
Insert the product's connectors and completely
remove the product from its holder
4
The product insertion screws must be tightened in the DOWN
direction, as shown in the figure, before inserting the modified
or de-supplied product. Do not place the product without checking.
Otherwise, the product will not sit, and the elevator mechanism
will be damaged if forced.
• The electrical conductor must be absolutely closed during the installation and uninstallation processes.
Uninstall