Herman Miller Nelson Bubble Lotus Table Lamp User manual

Herman Miller Nelson Bubble Lamp Series Assembly Instructions1Part # 1BTKPV Rev. A
Parts Included (Cigar shown, Others available)
No Tools Required
HermanMiller
Nelson™Bubble Lotus Table Lamp
Nelson™Bubble Lotus Floor Lamp
A. Lamp Shade
(Cigar Shown, Others available)
B. Shade Support and Base and Mounting
Screw
FOR INDOOR DRY LOCATION USE ONLY.
DO NOT COVER ANY PART OF THE LUMINAIRE.
LAMP IS HOT! WHEN TURNED OFF, ENSURE LAMP HAS COOLED
BEFORE CHANGING.
IF THE LUMINAIRE IS DAMAGED, IT SHOULD BE REPLACED, OR
REPAIRED BY THE MANUFACTURER OR THEIR SERVICE AGENT OR
SIMILAR QUALIFIED PERSON IN ORDER TO AVOID ANY HAZARD.
CAUTION
PLASTIC BAGS CAN BE DANGEROUS.
TO AVOID DANGER OF SUFFOCATION,
KEEP THIS BAG AWAY FROM BABIES AND CHILDREN
Only installed on large and medium
floor lamps.
Plastic polymer sprayed over a steel frame. Each Luminaire is supplied
with Lotus base and power cord.
The surface can be dusted with a so dry cloth. To remove dirt or grease,
use water with a mild soap and rub gently using a so white cloth or
paper towel.
Do not use solvent-based cleaners or glass cleaners on this product.
Please ensure luminaire is turned o during cleaning.
For translated versions of this document please visit the following links:
UK. hermanmiller.co.uk/nelson-bubble-lamps
FR. hermanmiller.fr/nelson-bubble-lamps
DE. hermanmiller.de/nelson-bubble-lamps
IT. hermanmiller.it/nelson-bubble-lamps
NL. hermanmiller.nl/nelson-bubble-lamps
Technical
Cleaning Instructions
Translations
All Luminaire vary in size and weight: *Typically
Small Shade = *.45kg; Medium Shade= *1.43 kg; Large Shade = *2.04 kg
Physical Specications
Table Base = *1.5 kg; Floor Base = *4.26 kg
Light source type: E27
Only use LED or Compact fluorescent energy saving lamps.
Lamp and colour to be specied separately.
Technical Specications
Class: 1 (This product must be earthed)
Input Voltage (VAC): Small Luminaire: 100 - 240V, all others
220-240V
Input Frequency (Hz): 50/60 Hz
Power Consumption (W): All Luminaire are individually marked
Ingress Protection: IP20
Operating Temperature Range: +25°C
Storage Temperature Range: -10°C to +50°C
Humidity (non-condensing): 20-50% Non-condensing, dry locations only
Electrical
Environmental
Floor Lamp Shown
110-240V

Herman Miller Nelson Bubble Lamp Series Assembly Instructions2Part # 1BTKPV Rev. A
** For Large and Medium Floor Lamps only:
Pivot the shade to the right while you angle the other half of the centering
cleat through the shade opening.
Step 3
**
Step 2
** For Large and Medium Floor Lamps only:
Pivot the shade to the le while you angle the centering cleat through the
opening of the shade.
**
1.1
Aer installing a light bulb, lower the lamp shade over the support frame.
1.2
With your free hand, slide the centering cleat up the lamp sha.
Step 1: (Table lamb and Floor lamb steps are the same except where
noted)
**
Use only in the manner intended by the manufacturer. If you have any
questions, contact the manufacturer.
Ensure the ambient in which the luminaire is to be operated will not exceed
the maximum luminaire rating.
Ensure the environment is a dry location.
Do not operate luminaire with damaged parts.
Turn power o before inspection, installation or removal.
Turn power o when changing lamp.
Warranty VOID if serviced.
BEFORE YOU BEGIN READ THESE INSTRUCTIONS COMPLETELY
AND CAREFULLY.
THIS PRODUCT CAN BE MOUNTED WITHIN ARM’S REACH.
Save These Instructions
Installation Pre-check
RISK OF ELECTRICAL SHOCK!
How to assemble your lamp

Herman Miller Nelson Bubble Lamp Series Assembly Instructions3Part # 1BTKPV Rev. A
Plug the power cord into an appropriate outlet and enjoy your Nelson Bubble
Floor Lamp.
For more information about the care and assembly of this product, please visit
hermanmiller.com/care-and-assembly.
HermanMiller and Yare among the registered trademarks of Herman Miller, Inc.
Nelson is among the trademarks of Herman Miller, Inc.
Printed in USA. Please recycle.
© 2016 Herman Miller, Inc., Zeeland Michigan. All rights reserved.
Step 6
Fasten the lamp shade screw to the threaded hole located at the top of the
lamp shade support.
Step 5
** For Large and Medium Floor Lamps only:
The cleat should be securely centered on the rim of the lamp shade, which
prevents it from rocking.
**
** For Large and Medium Floor Lamps only:
Once the cleat is fully inside the shade, slide it down the sha.
Step 4
**