hestan GIMR15 Quick guide

P/N 011026 rev B
Outdoor Ice Machine
Installation and Instruction
Manual
GIMR15
GIML15
15” OUTDOOR ICE MACHINE RIGHT HINGE
15” OUTDOOR ICE MACHINE LEFT HINGE

2
WARNING
Only qualied service technicians should install and service the ice machine. To
obtain the name and phone number of your local Hestan Certied Service
Representative, visit www.hestanoutdoor.com. No installation or service should be
undertaken until the technician has thoroughly read this Instruction Manual.
Likewise, the owner/manager should not proceed to operate the ice machine until
the installer has instructed them on its proper operation. Failure to install, operate,
and maintain the ice machine in accordance with this manual will adversely affect
safety, performance, component life, and warranty coverage and may result in
costly water damage. Proper installation is the responsibility of the installer. Product
failure or property damage due to improper installation is not covered under
warranty.
Hestan provides this manual primarily to assist qualied service technicians in the
installation, maintenance, and service of the ice machine.
Should the reader have any questions or concerns which have not been satisfactorily
addressed, please call, send an e-mail message, or write to the Hestan Technical Support
Department for assistance.
Phone: [phone]
E-mail: [e-mail]
Hestan Commercial
3375 E. La Palma Ave.
Anaheim, CA 92806
Web Site: www.hestanoutdoor.com
NOTE: To expedite assistance, all correspondence/communication MUST include the
following information:
• Model Number
• Serial Number
• Complete and detailed explanation of the problem.

3
CONTENTS
Important Safety Information ................................................................................................. 4
I. Specications...................................................................................................................... 6
A. Construction.................................................................................................................. 6
B. Electrical Data ............................................................................................................... 7
C. Dimensions/Connections .............................................................................................. 8
1. GIM_15 .................................................................................................................... 8
II. Installation Instructions ...................................................................................................... 9
A. Checks Before Installation............................................................................................. 9
B. Location......................................................................................................................... 9
1. General .................................................................................................................... 9
2. Built-In Installation Site .......................................................................................... 10
C. Setup............................................................................................................................11
D. Electrical Connection ...................................................................................................11
E. Water Supply and Drain Connections ......................................................................... 12
F. Final Checklist.............................................................................................................. 13
III. Operating Instructions..................................................................................................... 14
A. Important Notes About Usage..................................................................................... 14
B. Startup ........................................................................................................................ 14
IV. Maintenance ................................................................................................................... 17
A. Maintenance Schedule................................................................................................ 17
B. Cleaning and Sanitizing Instructions ........................................................................... 18
C. Storage Bin Drain........................................................................................................ 22
D. Condenser................................................................................................................... 23
E. Optional Drain Pump AGDP........................................................................................ 23
V. Preparing the Ice machine for Periods of Non-Use.......................................................... 25
VI. Disposal.......................................................................................................................... 25
IMPORTANT
This manual should be read carefully before the ice machine is installed and
operated. Read the warnings and guidelines contained in this booklet carefully as
they provide essential information for the continued safe use and maintenance
of the ice machine. Retain this booklet for any further reference that may be
necessary.

4
Important Safety Information
Throughout this manual, notices appear to bring your attention to situations which could
result in death, serious injury, damage to the appliance, or damage to property.
WARNING Indicates a hazardous situation which could result in death or
serious injury.
NOTICE Indicates a situation which could result in damage to the
appliance or property.
IMPORTANT Indicates important information about the installation, use, and
care of the appliance.
WARNING
This ice machine should be destined only to the use for which it has been expressly
conceived. Any other use should be considered improper and therefore dangerous.
The manufacturer cannot be held responsible for injury or damage resulting from
improper, incorrect, and unreasonable use. Failure to install, operate, and maintain the
ice machine in accordance with this manual will adversely affect safety, performance,
component life, and warranty coverage and may result in costly water damage.
To reduce the risk of death, electric shock, serious injury, or re, follow basic
precautions including the following:
• Only qualied service technicians should install and service this ice machine.
• This ice machine must be installed in accordance with applicable national, state, and
local codes and regulations.
• This ice machine requires an independent power supply of proper capacity. See the
nameplate for electrical specications. Failure to use an independent power supply of
proper capacity can result in a tripped breaker, blown fuse, damage to existing wiring,
or component failure. This could lead to heat generation or re.
• THIS ICE MACHINE MUST BE GROUNDED: This ice machine is equipped with
a NEMA5-15 three-prong grounding plug to reduce the risk of potential shock
hazards. It must be plugged into a properly grounded, independent 3-prong wall outlet.
If the outlet is a 2-prong outlet, it is your personal responsibility to have a qualied
electrician replace it with a properly grounded, independent 3-prong wall outlet. Do not
remove the ground prong from the power cord and do not use an adapter plug.
• Do not use an extension cord.
• To reduce the risk of electric shock, make sure the control switch is in the "OFF"
position before plugging in or unplugging the ice machine.
• To reduce the risk of electric shock, do not touch the control switch or plug with damp
hands.
• Do not use an ice machine with a damaged power cord. The power cord should not be
altered, jerked, bundled, weighed down, pinched, or tangled. Such actions could result
in electric shock or re. To unplug the ice machine, be sure to pull the plug, not the
cord, and do not jerk the cord.
• Do not make any alterations to the ice machine. Alterations could result in electric
shock, injury, re, or damage to the ice machine.

5
WARNING, continued
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory, or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be properly supervised around this appliance.
• Do not climb, stand, or hang on the ice machine door or allow children or animals to do
so. Serious injury could occur or the ice machine could be damaged.
• Be careful not to pinch ngers when opening and closing the door. Be careful when
opening and closing the door when children are in the area.
• Do not use combustible spray or place volatile or ammable substances near the ice
machine. They might catch re.
• Keep the area around the ice machine clean. Dirt, dust, or insects in the ice machine
could cause harm to individuals or damage to the ice machine.
NOTICE
• Protect the oor when moving the ice machine to prevent damage to the oor.
• Follow the water supply, drain connection, and maintenance instructions carefully to
reduce the risk of costly water damage.
• In areas where water damage is a concern, install in a contained area with a oor drain.
• Install the ice machine in a location that stays above freezing. Normal operating
ambient temperature must be within 45°F to 100°F (7°C to 38°C).
• If using the optional drain pump (AGDP), test its operation every time the ice machine
is cleaned and sanitized. See "IV.E. Optional Drain Pump AGDP" for details. If the
optional drain pump is not operating properly, water could back up and overow,
leading to costly water damage.
• To help ensure that the storage bin drain remains clear, follow the instructions in "IV.C.
Storage Bin Drain" once every 3 months or as often as necessary for conditions. If
the storage bin drain becomes clogged, water could build up in the bin and overow,
leading to costly water damage.
• If water collects in the bin and will not drain, turn off the ice machine and close the
water supply line shut-off valve. Call for service.
• Do not leave the ice machine on during extended periods of non-use, extended
absences, or in sub-freezing temperatures. To properly prepare the ice machine for
these occasions, follow the instructions in "V. Preparing the ice machine for Periods of
Non-Use."
• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear
of obstruction.
• Do not place objects on top of the ice machine.
• The storage bin is for ice use only. Do not store anything else in the storage bin.

6
I. Specications
A. Construction
Top Panel
Ice Making
Mechanism
Scoop Holder
Front Panel
Control Switch
Louver
Bin Control
Thermostat
Bulb
Slope
Magnet
Catch
Door
Power Cord

7
HESTAN ICE MACHINE
MODEL NUMBER GIM_15
SERIAL NUMBER
AC SUPPLY VOLTAGE 115-120/60/1
AMPERES 3.8 AMPS
DESIGN PRESSURE HI-240PSI LO-120PSI
REFRIGERANT 134a 4.2 OZ.
B. Electrical Data
See the nameplate for electrical and refrigeration specications. The nameplate is located
inside the storage bin.
We reserve the right to make changes in specications and design without prior notice.
Note: In the "MODEL NUMBER" the _ references either a (L) Left or (R) Right hinge
model

8
C. Dimensions/Connections
GIM_15
Units: mm [in.]

9
II. Installation Instructions
WARNING
• This ice machine must be installed in accordance with applicable national, state,
and local codes and regulations.
• CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews
are securely in place after installation. Make sure that none have fallen into the
storage bin.
A. Checks Before Installation
• Visually inspect the exterior of the shipping container and immediately report any
damage to the carrier. Upon opening the container, any concealed damage should also
be immediately reported to the carrier.
• Remove the shipping carton, tape, and packing material. If any are left in the ice
machine, it will not work properly.
• Remove the package containing the accessories.
• Remove the protective plastic lm from the panels. If the ice machine is exposed to the
sun or to heat, remove the lm after the ice machine cools.
• See the nameplate inside the storage bin, and check that your voltage supplied
corresponds with the voltage specied on the nameplate.
B. Location
1. General
This ice machine is approved for indoor or outdoor use.
NOTICE
• Normal operating ambient temperature must be within 45°F to 100°F (7°C to
38°C); Normal operating water temperature must be within 45°F to 95°F (7°C
to 35°C). Operation of the ice machine, for extended periods, outside of these
normal temperature ranges may affect ice machine performance.
• This ice machine will not work at sub-freezing temperatures. To prevent damage
to the water supply line, drain the ice machine if the air temperature is going to go
below 32°F (0°C). See "V. Preparing the Ice machine for Periods of Non-Use."
For best operating results:
• The ice machine should not be located next to ovens, grills, or other high heat
producing equipment.
• The location must provide a rm foundation for the ice machine.
• This ice machine requires no side or top clearance. But allow enough space at rear for
water supply and drain connections and at least 15" (38 cm) clearance at front.
• The ice machine must be at oor level on a nished oor even if under a cabinet. In
areas where water damage is a concern, install in a contained area with a oor drain.

10
2. Built-In Installation Site
NOTICE
• Do not let the weight of the counter rest on the ice machine.
• Do not install the ice machine in a corner where the door will interfere with other
equipment or where the ice machine cannot be pulled out for service.
Installation Space
Model Height Width Depth
GIM_15 34" (864 mm) minimum 15" (381 mm) minimum 24" (610 mm) minimum
Min. 34"
(864 mm) Min. 15"
(381 mm)
Between Two Cabinets Between a Cabinet and
the End of a Counter
Support: Do not
let the weight
of the counter
rest on the ice
machine
Min. 23"
(584 mm)
Oven Ice machine
Between a Cabinet and
a Wall or Tall Cabinet
In a Corner
Secure: Do not
let the weight
of the counter
rest on the ice
machine
Min. 15"
(381 mm)
Min. 34"
(864 mm)

11
C. Setup
1) Position the ice machine in the selected permanent location.
2) Level the ice machine from side-to-side and front-to-rear by adjusting the feet.
D. Electrical Connection
WARNING
• Electrical connection must meet national, state, and local electrical code
requirements. Failure to meet these code requirements could result in death,
electric shock, serious injury, re, or severe damage to equipment.
• This ice machine requires an independent power supply of proper capacity. See
the nameplate for electrical specications. Failure to use an independent power
supply of proper capacity can result in a tripped breaker, blown fuse, damage to
existing wiring, or component failure. This could lead to heat generation or re.
• THIS ICE MACHINE MUST BE GROUNDED: This ice machine is equipped with
a NEMA 5-15 three-prong grounding plug to reduce the risk of potential shock
hazards. It must be plugged into a properly grounded, independent 3-prong wall
outlet. If the outlet is a 2-prong outlet, it is your personal responsibility to have
a qualied electrician replace it with a properly grounded, independent 3-prong
wall outlet. Do not remove the ground prong from the power cord and do not use
an adapter plug. Failure to follow these instructions may result in death, electric
shock, or re.
• Do not use an extension cord.
• To reduce the risk of electric shock, make sure the control switch is in the "OFF"
position before plugging in or unplugging the ice machine.
• To reduce the risk of electric shock, do not touch the control switch or plug with
damp hands.
• Do not use an ice machine with a damaged power cord. The power cord should
not be altered, jerked, bundled, weighed down, pinched, or tangled. Such actions
could result in electric shock or re. To unplug the ice machine, be sure to pull the
plug, not the cord, and do not jerk the cord.
• The GREEN ground wire in the factory-installed power cord is connected to
a screw on the rear panel where the power cord enters the ice machine. If it
becomes necessary to remove or replace the power cord, be sure to connect the
power cord's ground wire to this screw upon reattachment.
• Usually an electrical permit and services of a licensed electrician are required.
• The maximum allowable voltage variation is ±10 percent of the nameplate rating.
• For optional drain pump (AGDP) installation, refer to the instructions included with the
pump.

12
E. Water Supply and Drain Connections
WARNING
Water supply and drain connections must be installed in accordance with applicable
national, state, and local regulations.
NOTICE
• Normal operating water temperature must be within 45°F to 95°F (7°C to 35°C).
Operation of the ice machine, for extended periods, outside of this normal
temperature range may affect ice machine performance.
• To prevent damage to the ice machine, do not operate the ice machine when
the water supply is off, or if the pressure is below 10 PSIG. Do not run the ice
machine until the proper water pressure is reached.
• Connect to potable water supply only. Do not connect to a hot-water supply.
• In areas where water damage is a concern, install in a contained area with a oor
drain.
• Water line installation to the ice machine is not warranted by Hestan.
• Water-hammer issues must be resolved by a qualied plumber before installing
the ice machine. Water hammer can cause ice machine damage that may lead to
water leakage or ooding.
• If using the optional drain pump (AGDP), test its operation every time the ice
machine is cleaned and sanitized. See "IV.E. Optional Drain Pump AGDP" for
details. If the optional drain pump is not operating properly, water could back up
and overow, leading to costly water damage.
• A plumbing permit and services of a licensed plumber may be required in some areas.
• External lters, strainers, or softeners may be required depending on water quality.
Contact your local Hestan Certied Service Representative for recommendations.
• Water supply inlet is 1/2" female pipe thread (FPT).
Fig. 30
Water Supply Line
Shut-Off Valve
Water Supply Line
Drain Valve
Water Supply Inlet
1/2" FPT
Drain Outlet
1/2" FPT
Piping to approved drain. Leave a
2-inch (5-cm) vertical air gap between
the end of the pipe and the drain.
2-inch (5-cm)
air gap
Floor
Drain
Vented Tee Connection
Extend the vent at least
12" (30 cm) above the
drain outlet.
Minimum 1/4" Nominal ID
Copper Water Tubing or
Equivalent
Minimum 1/2"
Nominal ID Hard Pipe
or Equivalent

13
• A water supply line shut-off valve and drain valve must be installed. A minimum of
1/4" nominal ID copper water tubing or equivalent is required for the water supply line.
Be sure there is sufficient extra water supply line for the unit to be pulled out for service.
• Water supply pressure must be a minimum of 10 PSIG and a maximum of 113 PSIG. If
the pressure exceeds 113 PSIG, the use of a pressure reducing valve is required.
• Drain outlet is 1/2" FPT. A minimum of 1/2" nominal ID hard pipe or equivalent is
required for the drain line. Installing a smaller diameter drain line will reduce water ow
and may lead may lead to water leakage or ooding. Be sure there is sufficient extra
drain line for the unit to be pulled out for service.
• Drain line should not be piped directly to the sewer system. An air gap of a minimum
of 2 vertical inches (5 cm) must be between the end of the drain pipe from the ice
machine and the oor drain.
• For gravity drain installation, drain must have 1/4" fall per foot (2 cm per 1 m) on
horizontal runs to get good ow. A vented tee connection is also required for proper
ow. Extend the vent at least 12" (30 cm) above the drain outlet.
• For optional drain pump (AGDP) installation, refer to the instructions included with the
pump.
F. Final Checklist
WARNING
CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are
securely in place after installation. Make sure that none have fallen into the storage
bin.
1) Is the ice machine level?
2) Is the ice machine in a site where the ambient temperature is within 45°F to 100°F (7°C
to 38°C) and the water temperature within 45°F to 95°F (7°C to 35°C) all year around?
3) Have the shipping carton, tape, and packing material been removed from the ice
machine? Hasthe protective plastic lm been removed from the panels?
4) Have all electrical and water connections been made? Do electrical and water
connections meet all national, state, and local code and regulation requirements?
5) Has the power supply voltage been checked or tested against the nameplate rating? Is
the power supply a properly grounded, independent 3-prong wall outlet?
6) Are the water supply and drain lines sized as specied? Are the water supply line
shut-off valve and drain valve installed? Has the water supply pressure been checked to
ensure a minimum of 10 PSIG and a maximum of 113 PSIG?
7) Are all components, fasteners, and thumbscrews securely in place?
8) Has the end user been given this instruction manual, and instructed on how to operate
the ice machine and the importance of the recommended periodic maintenance?
9) Has the end user been given the name and telephone number of an authorized service
agent?
10) Has the warranty tag been lled out and forwarded to the factory for warranty
registration?

14
III. Operating Instructions
A. Important Notes About Usage
WARNING
• Only qualied service technicians should install and service the ice machine.
• Failure to install, operate, and maintain the ice machine in accordance with this
manual will adversely affect safety, performance, component life, and warranty
coverage.
• To reduce the risk of electric shock, make sure the control switch is in the "OFF"
position before plugging in or unplugging the ice machine.
• To reduce the risk of electric shock, do not touch the control switch or plug with
damp hands.
• This ice machine must be maintained in accordance with the instruction manual
and labels provided with the ice machine. Consult with your local Hestan Certied
Service Representative about maintenance service.
• This ice machine must be cleaned and sanitized at least once a year. More
frequent cleaning and sanitizing may be required in some water conditions.
• Wash your hands before removing ice. Use the plastic scoop provided.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory, or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Children should be properly supervised around this appliance.
• Do not climb, stand, or hang on the ice machine or ice machine door or allow
children or animals to do so. Serious injury could occur or the ice machine could
be damaged.
• Be careful not to pinch ngers when opening and closing the door. Be careful
when opening and closing the door when children are in the area.
• Do not use combustible spray or place volatile or ammable substances near the
ice machine. They might catch re.
• Keep the area around the ice machine clean. Dirt, dust, or insects in the could
cause harm to individuals or damage to the ice machine.

15
NOTICE
• Protect the oor when moving the ice machine to prevent damage to the oor.
• If using the optional drain pump (AGDP), test its operation every time the ice
machine is cleaned and sanitized. See "IV.E. Optional Drain Pump AGDP" for
details. If the optional drain pump is not operating properly, water could back up
and overow, leading to costly water damage.
• To help ensure that the storage bin drain remains clear, follow the instructions
in "IV.C.Storage Bin Drain" once every 3 months or as often as necessary for
conditions. If the storage bin drain becomes clogged, water could build up in the
bin and overow, leading to costly water damage.
• If water collects in the bin and will not drain, turn off the ice machine and close the
water supply line shut-off valve. Call for service.
• Do not leave the ice machine on during extended periods of non-use, extended
absences, or in sub-freezing temperatures. To properly prepare the ice machine
for these occasions, follow the instructions in "V. Preparing the Ice machine for
Periods of Non-Use."
• Keep ventilation openings, in the appliance enclosure or in the built-in structure,
clear of obstruction.
• Do not place objects on top of the ice machine.
• The storage bin is for ice use only. Do not store anything else in the storage bin.
B. Startup
WARNING
All parts are factory-adjusted. Improper adjustments may adversely affect safety,
performance, component life, and warranty coverage.
NOTICE
• If the ice machine is turned off, wait for at least 3 minutes before restarting the ice
machine to prevent damage to the compressor.
• At startup, conrm that all internal and external connections are free of leaks.
1) Open the water supply line shut-off valve.
2) Make sure the control switch is in the "OFF" position. Plug the unit into the electrical
outlet. WARNING! To reduce the risk of electric shock, do not touch the control
switch or plug with damp hands. If you have to slide the unit back for a built-in
installation, make sure you do not damage or pinch the water supply line, drain line, or
power cord.
3) If required by sanitation code in your area, seal the perimeter where the machine
touches the oor with approved caulk compound in a smooth and easily cleanable
manner.

16
4) Move the control switch to the "ICE" position and allow the ice machine to operate for
2 minutes. This allows the water tank to ll.
5) Move the control switch to the "OFF" position.
6) Inside the storage bin, disconnect the suction tube by squeezing the tabs and pulling
the tube clear. See Fig. 31. Allow the water tank to drain.
7) Reconnect the suction tube as illustrated. See Fig. 32. Make sure the tabs lock into
place; a loose tting may cause a water leak.
8) Clean the storage bin liner, door liner, and door gasket using a neutral cleaner. Rinse
thoroughly after cleaning.
9) Move the control switch to the "ICE" position to start the automatic icemaking process.
10) To conrm bin control operation, hold ice in contact with the bin control thermostat
bulb. NOTICE! If the ice machine does not stop within 10 seconds, the bin control
thermostat must be adjusted. Installation at higher altitude locations are more
likely to require adjustment. See Fig. 33.
Water Tank
Drain
Suction Tube
Tabs
Fig. 31 Fig. 32
Suction Tube
Tabs
Fig. 33
Bin Control
Thermostat

17
IV. Maintenance
This ice machine must be maintained in accordance with the instruction manual and
labels provided with the ice machine. Consult with your local Hestan Certied Service
Representative about maintenance service.
WARNING
• Only qualied service technicians should service this ice machine.
• Failure to install, operate, and maintain the ice machine in accordance with this
manual will adversely affect safety, performance, component life, and warranty
coverage.
• Move the control switch to the "OFF" position and unplug the ice machine from
the electrical outlet before servicing.
• To reduce the risk of electric shock, do not touch the control switch or plug with
damp hands.
• CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are
securely in place after any maintenance is performed. Make sure that none have
fallen into the storage bin.
• After service, make sure that there are no wires pinched between the panels and
ice machine. Make sure you do not damage or pinch the water supply line, drain
line, or power cord.
A. Maintenance Schedule
The maintenance schedule below is a guideline. More frequent maintenance may be
required depending on water quality, the ice machine's environment, and local sanitation
regulations.
Maintenance Schedule
Frequency Area Task
Weekly Scoop Clean the scoop using a neutral cleaner. Rinse thoroughly after cleaning.
Monthly External Water
Filters
Check for proper pressure and change if necessary.
Ice machine
Exterior
Wipe down with clean, soft cloth. Use a damp cloth containing a neutral
cleaner to wipe off oil or dirt build up. Clean any chlorine staining (rust
colored spots) using a non-abrasive cleaner like Zud or Bon Ami.
Every 3
Months
Storage Bin Drain Maintain as outlined in "IV.C. Storage Bin Drain."
Yearly Ice machine and
Storage Bin
Clean and sanitize per the cleaning and sanitizing instructions provided in
this manual. See "IV.B. Cleaning and Sanitizing Instructions."
Optional Drain
Pump (AGDP)
Test as outlined in "IV.E. Optional Drain Pump AGDP."
Water Supply Inlet Close the ice machine water supply line shut-off valve and drain the water
system. Clean the water supply inlet screen.
Condenser Inspect. Clean if necessary. See "IV.D. Condenser."
Water Hoses Inspect the water hoses and clean/replace if necessary.

18
B. Cleaning and Sanitizing Instructions
This ice machine must be cleaned and sanitized at least once a year. More frequent
cleaning and sanitizing may be required in some water conditions.
WARNING
• To prevent injury to individuals and damage to the ice machine, do not use
ammonia type cleaners.
• Carefully follow any instructions provided with the bottles of cleaning and
sanitizing solution.
• Always wear liquid-proof gloves and goggles to prevent the cleaning and sanitizing
solutions from coming into contact with skin or eyes.
• After cleaning and sanitizing, be careful not to leave any solution in the ice
machine.
1. Cleaning Solution
Dilute 5 . oz. (148 ml or 10 tbs) of "Scale Away" with 1gallon (3.8 l) of warm water. This
is a minimum amount. Make more solution if necessary. IMPORTANT! For safety and
maximum effectiveness, use the solution immediately after dilution.
2. Cleaning Procedure
1) Remove all ice from the evaporator and the storage bin.
Note: To remove cubes on the evaporator, move the control switch to the "OFF" position
and then move it back to the "ICE" position after 3 minutes. The harvest cycle
starts and the cubes will be removed from the evaporator.
2) Move the control switch to the "OFF" position.
3) Inside the storage bin, disconnect the suction tube by squeezing the tabs and pulling
the tube clear. See Fig. 34. Allow the water tank to drain.
4) Reconnect the suction tube as illustrated. See Fig. 35. Make sure the tabs lock into
place; a loose tting may cause a water leak.
5) Slowly pour the cleaning solution into the water tank.
Water Tank
Drain
Suction Tube
Tabs
Fig. 34 Fig. 35
Suction Tube
Tabs

19
6) Move the control switch to the "WASH" position.
7) Allow the cleaning solution to circulate for 30 minutes, then move the control switch to
the "OFF" position.
8) Disconnect the suction tube. Allow the water tank to drain, then reconnect the suction
tube.
9) Move the control switch to the "ICE" position and allow the ice machine to operate for
2 minutes. This allows the water tank to ll with water.
10) Move the control switch to the "WASH" position.
11) Allow the water to circulate for 5 minutes, then move the control switch to the "OFF"
position.
12) Disconnect the suction tube. Allow the water tank to drain, then reconnect the suction
tube.
13) Repeat steps 9 through 12 three more times to rinse thoroughly.
3. Sanitizing Solution
Dilute 0.5 . oz. (14.8 ml or 1 tbs) of a 5.25% sodium hypochlorite solution (chlorine
bleach) with 1 gallon (3.8 l) of warm water. This is a minimum amount. Make more
solution if necessary. Using a chlorine test strip or other method, conrm that you have a
concentration of about 200 ppm. IMPORTANT! For safety and maximum effectiveness,
use the solution immediately after dilution.
4. Sanitizing Procedure
1) Make sure the control switch is in the "OFF" position and the storage bin is empty.
2) Remove the slope from the storage bin by carefully bending it in the center and
releasing it from the 2 slope shafts. See Fig. 36.
3) Remove each separator by lifting it to the horizontal position and pushing it hard inward.
See Fig. 37.
Separator
Slope
Fig. 36 Fig. 37
Slope Shafts

20
4) Disconnect the suction tube. Allow the water tank to drain.
5) Spread out the tabs to unlock the water tank, then slide it out. See Fig. 38.
6) Lift off the ice chute from the front frame pipe and then from the rear frame pipe. See
Fig. 39.
Ice Chute
Front Frame Pipe
Ta b Ta b
Fig. 38 Fig. 39
Rear Frame Pipe
Water Tank
7) Disconnect the discharge tube from the spray assembly, then slide out the spray
assembly. See Fig. 40.
8) Remove the two caps. See Fig. 41.
Reducing Pipe
Rail Rail
Fig. 42 Fig. 43
Discharge Tube
Spray Assembly
Fig. 40 Fig. 41
Right BracketLeft Bracket
Caps
Discharge Tube
Caps
9) Soak all of the removed parts and the scoop in the sanitizing solution for 10 minutes. If
the spray assembly nozzles are clogged, clean them with a wire or a suitable brush.
10) Rinse the parts thoroughly with clean water.
11) Ret the 2 caps in their correct positions. Make sure the reducing pipe is in place in the
center. See Fig. 42.
12) Slide in the spray assembly along the rails on the left and right brackets. See Fig. 43.
Connect the discharge tube securely to the spray assembly; a loose tting may cause a
water leak.