HIK VISION DS-2CE16 T-IR User manual

TVI Bullet &Turret Camera
User Manual
Thank you for purchasing our product. If there
are any questions, or requests, please do not
hesitate to contact the dealer.
This manual may contain several technical
incorrect places or printing errors, and the
content is subject to change without notice.
The updates will be added to the new version of
this manual. We will readily improve or update
the products or procedures described in the
manual.
Regulatory Information
FCC Information
FCC compliance: This equipment has been
tested and found to comply with the limits for a
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated in
a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio
communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
0100001050203
FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
EU Conformity Statement
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
2006/66/EC (battery directive):
This product contains a battery that
cannot be disposed of as unsorted
municipal waste in the European
Union.
See the product documentation for specific
battery information. The battery is marked with
this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your
supplier or to a designated collection point. For
more information see: www.recyclethis.info.
This series of camera adopts new generation
sensor with high sensitivity and advanced circuit
design technology It features high resolution,.
low image distortion and low noise, etc , which.
makes it suitable for surveillance system and
image processing system.
l High performance CMOS sensor and high
resolution bring high-quality image;
l Low illumination;
l Support auto white balance, auto gain control,
electronic shutter control;
l Unit transmission control;
l Advanced 3-axis design meets different
installation requirements.
1 Introduction
1.1 Product Features
1.2 Overview
UD.6L0201D1789A01
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European
Union. For proper recycling, return
this product to your local supplier
Please refer to the product specification for
camera parameters and functions.
This product and - if applicable - the
supplied accessories too are marked
with "C E" and comply therefore with
the applicable harmonized European
standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC,
the RoHS Directive 2011/65/EU.
1.2.1 Overview of Type I Camera
TURBO HD
Type
Type I
Model
DS-2CE16 T-IRC0
DS-2CE16 T-IC0 RP
Mounting Base
HD Video Cable
Power Cable
Sun Shield
Lens
IR LED
1.2.2 Overview of Type II Camera
Type II DS-2CE56C0T-IRM
DS-2CE56C0T-IRP
DS-2CE56C0T-IR
Privacy Notice
Surveillance laws vary by jurisdiction. Check all
relevant laws in your jurisdiction before using
this product for surveillance purposes to ensure
HD Video Cable
Mounting Base
Camera
Trim Ring Enclosure
Power Cable
Side Opening
1.2.3 Overview of Type III Camera
Enclosure
HD Video Cable
Mounting Base
Power Cable
Camera
Trim Ring
Type III
2 Installation
Before you start:
l Please make sure that the device in the package
is in good condition and all the assembly parts
are included.
l Make sure that all the related equipment is
power-off during the installation.
l Check the specification of the products for the
installation environment.
l Check whether the power supply is matched
with your power output to avoid damage.
l Please make sure the wall is strong enough to
withstand three times the weight of the camera
and the mounting.
l If the wall is the cement wall, you need to insert
expansion screws before you install the camera.
If the wall is the wooden wall, you can use
self-tapping screw to secure the camera.
l If the product does not function properly,
please contact your dealer or the nearest
service center. Do not disassemble the camera
for repair or maintenance by yourself.

5.Adjust the surveillance angle.
1).Loosen No.3 adjusting screw to adjust the
panning position 0 ~ 360 .(° °)
.2).Tighten No.3 adjusting screw
3).Loosen the No.2 adjusting screw to adjust the
tilting position 0 ~ 90(° °).
4).Tighten No.2 adjusting screw.
5).Loosen No.1 adjusting screw to adjust the
azimuth angle of the image 0 ~ 360(° °).
.6).Tighten No.1 adjusting screw
Figure 2-3 3-axis Adjustment
3.Connect the corresponding power cable and
video cable.
4.Fix the camera to the ceiling with the supplied
screws.
Figure 2-2 Fix the Camera to the Ceiling
360°
90°
360°
3
2
1
2.2 Installation of Type II Camera
Steps:
1.Drill the screw holes according to the drill
template.
Figure 2-4 The Drill Template
2. Screw the clip plate onto the mounting base
loosely.
Figure 2-5 Screw the Clip Plate
Clip Plate
Figure 2-1 The Drill Template
Screw hole
Figure 2-6 Fix the the Camera
6.Adjust the camera according to the figure below
to get an optimum angle.
Figure 2-7 3-axis Adjustment
0 ~360°°
0~75°°
0 ~360°°
Clip Plate
3. Fix the mounting base to the ceiling with the
supplied screws.
4.Route the cables through the side opening and
connect the corresponding power cable and
video cable.
5.Pull out the clip plate and secure the camera
with the trim ring to the mounting base.
6.Push the clip plate in and tighten the lock screw
to secure the trim ring.
2.3 Installation of Type CameraIII
1.Drill the screw holes and the cable hole on the
ceiling according to the supplied drill template.
Steps:
Figure 2-8 The Drill Template
Figure 2-9 Fix the Mounting Base and Camera
2.Fix the mounting base to the ceiling with the
supplied screws.
3.Route the cables to the cable hole and connect
corresponding power cable and video cable.
4.Secure the camera to the mounting base.
5.
Adjust the camera according to the figure below
to get an optimum angle.
0~360°°
0~75°°
0~360°°
Figure 2-10 3-axis Adjustment
Screw Hole
Cable Hole
7.Adjust the camera according to the figure 2-7 to
get an optimum angle and tighten the trim ring.
Steps:
1.Drill the screw holes in the ceiling according
to the supplied drill template.
2.Hammer the supplied plastic expansion bolt into
the screw holes.
Screw hole
Side Opening
2.1 Ceiling Mounting for Type I
Camera
Both wall mounting and ceiling mounting are
suitable for type bullet camera. Ceiling mountingI
will be taken as an example in the section. And you
can take steps of ceiling mounting as a reference
if wall mounting is adopted.