Atdec AWM-FC User manual

AWM-FC Page 1 of 4
Installation Guide
AWM-FC
C Clamp
A
C Clamp Bracket
(x1)
B
C Clamp Plate
(x1)
C
Cover for Post
(x1)
D
Cover for Base
(x1)
E
4mm
Hex Key
(x1)
F
5mm
Hex Key
(x1)
COMPONENT CHECKLIST
REQUIRED TOOLS
• All tools supplied
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is compatible with Atdec AWM Series modular products, including Posts (AWM-P) and Base (AWM-LB).
! The manufacturer accepts no responsibility for incorrect installation.
! Product must only be installed on a work surface capable of supporting the weight of all equipment being mounted.
! Product is not suitable for installation on work surfaces with a bullnose or bevelled edge.

AWM-FC Page 2 of 4
1. Check mounting surface thickness
2. Re-congure clamp pad
1.1 For THICKNESS - 25 - 33mm ( 1 - 15 /
16”)
Go to Step 3. The clamp pad is already
congured for these work surface thicknesses.
1.2 For THICKNESS 18 - 25mm (11/
16 - 1”)
Go to Step 2. The clamp pad needs to be inverted.
3. Post mount conguration (go to Step 5 for base mount installation)
Fasteners
supplied
with post
Tighten
Firmly
!
3.2 Place in desired location. 3.3 Slide the C Clamp bracket over
the plate and position screw tips in
the indents on the base plate.
NOTE: Ensure the bracket
screws are retracted
using 4mm Hex Key
3.1 Attach plate to post.
Desk Clamp
Bracket
Mounting
surface
Pad
M8 x 16mm
Set Screw
3.4 Check the set screws are mounted in position. Also check the desk
clamp bracket is positioned tight up against the mounting surface edge.
3.5 Tighten the set screws on both sides of the
desk clamp bracket evenly.
2.1 Slide pad off. 2.3 Invert pad. 2.3 Slide pad back on.

AWM-FC Page 3 of 4
PUSH
HOOK
PUSH
4. Fitting C Clamp cover to post
5. Base mount installation
4.1 Un-clip cable clips
and covers from post.
4.2 Locate the C Clamp cover over the post. Guide
over the holes in the base plate and gently apply
pressure on the cover until it clicks into place.
4.3 Re-attach the cable clips and covers
(this can be done during the cable
management step when installing the
monitor arm).
Click!
5.1 Attach plate to base
5.5 Tighten the set screws and on both sides of the
desk clamp bracket
5.4 Check the set screws are mounted in position. Also check the
desk clamp bracket is positioned tight up against the mounting
surface edge.
5.2 Place the base and plate in
desired location
5.3 Slide the bracket onto the base
plate and position screw tips in the
indents on the base plate
NOTE: You may need to un-screw the
set screws out of the plate using the
5mm Hex Key
Fasteners
supplied
with base
Tighten
Firmly
!
!
Desk Clamp
Bracket
Mounting
surface
Pad
M8 x 16mm
Set Screw

AWM-FC Page 4 of 4
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20230929
6. Fitting C Clamp cover to base
6.1 Locate the Cover for Base over the base. Guide over the
holes in the base plate and gently apply pressure on the
cover until it clicks into place.
6.2 Installation Complete
To continue with installation of your
monitor mount, refer to your monitor arm’s
installation guide.
Click!
i