Hiltron security XM22K User manual

XM22K
1
Console XM with key KEY
!Alphanumeric LCD display LCD backlit(2x16 caracters)
!Protection tamper anti opening and tear-resistant
!Color white
!Input programmables 1
!Reader for proximity key integrated
!Buzzer
!Power Supply 12Vcc ±5%
!LED signalisation
!Degree case protection IP40
!Logic output of collector opened 30mAmax. 1
!Exterior caseABS
!Degree security 1
!Environmental Class 2
!Dimensions (LxAxP) 107x141x25mm
!Complies with standards CEI EN 50131-1
Installation
!Don’t install the console in places exposed at extreme temperatures or bad weather.
!To fix the consolat a height that let an easy access to the frontal panel.
!For a solide and accurate fixing ,it’s essential make sure that the supporting surface is plain.
against tampering, but the installation in a protected local and eventually
in the covering zoneof a volumetric detector is a supplementary protection.
NOTES: The console are protected
Close the screw like in the figure
to fix the cover with base
The fund of the consolle can be mounted on a
common mural box type “503”.
For a tear-resistant protection,to fix
with the screw included
Pb
Lead free
RoHS
compliant
Pb
Lead free
RoHS
compliant
Pb
Lead free
RoHS
compliant
Pb
Lead free
RoHS
compliant
RAEE
security
Made in Italy
BT2014/35/UE
EMC2014/30/UE

2
Key reader XM22K (Type 08)
The console XM22K is composed of a proximity key reader :
&For use it it’s necessary to connect also the blue cable on the Multiplexer line.
&To recognise and to programm the proximity reader to reference to paragraph 6.5 Programming Zone
of manual “INSTALLATION AND SETUP” SerieXM
XM22K- Console XM with key KEY security
Cable Console (Type 04)
The console is equipped with :
&An input (with reference to negative 12V) programmable like in the table “PARAMETERS” that is added
to those in the central unit.
&An output to opened collector (with reference to positive 12V) programmable.
NOTES: The positive '+' and the negative '-' on the terminal block 'Console' of the central unit are
electrically the same '+ EXT and 'GND' that feed multiplexer line
XM22K
IN
OUT
GND +12 +In +SA COM + SIR + OUT
011
010
AUX
GND MPX -+A B
Consolle
IN GND IN IN GND IN
009 010 011 012
009 EXT
CENTRALE SERIE XM
Black / : GND
Blue / : MPX
Red / : +12V EXT
Yellow / : Line console RS485B
Green/ : Line console RS485A
Red
Green Yellow Black
GND
MPX
OUT IN B A + 12V -
Blue
Black

Programming console
To change the language of the console:
!when it’s on for the first time ,use the bottons and for to choose the language indicated the
display
!Pressthe button to confirm
To visualize and/or to modify the language selected to remove and then turn on the console, the to
press 4 times ; in30 seconds
NOTES: if the console isn’t connected to the multiplexer line the change of the language it’s always
possible,typing 4 times 4 the button
ID Configuration
Every console standard has the ID setted to “01”. To install more console on the multiplexer line it’s
necessary to assign different ID (until 8 ID).
To change ID of the console :
!To give power to console
!Hold down for 5 seconds; is visualized the current ID
!Use the bottons and to chose the ID
!To press to confirm
NOTES: If the console isn’t connected to the data line (AB) the change of ID is always possible.
NOTES: if connect the positive '+' and negative '-' of the console on a battery is possible to read the
voltage of this last one. One time connected the console to the multiplexer line, the information
obtained is sent to the central unit in order to be read it by others consoles.
Functioning LED
On the console XM22K two LED indicate normally the status of inserter inside. If is pressed an any
botton two LED indicate,instead, the status of the console for 5 seconds.
NOTES :If install the console on central units that managemore of one installation, LED will signal
the status of inserter. It’s possibile to associate both the console, that the reader integrated
at the same installation.
Backlight Display
Tapyng the button for about 3 seconds, the backlights of display are off contemporary of keyboard
and the logo.
Taping instead the button LED signalisation of the status of installation are off.
For riactivate the normal functioning it’s necessary to press the button for about 3 seconds.
With the console off , acting on any button of backlight is riactivated for about 20 seconds allowing the
use of the same.
SIGNALISATION POWER SUPPLY ERROR.
Disable 24h
In case of disable of 24h, the flashing occur only on the console of addresse “1”.
XM22K- Console with alphanumeric display Serie XM
3
9
1
7
0
0
security

4
Table reader console XM22K (Type 08)
The following table shows which are the main functions of Type08
ENABLING01
PARAMETERS
DESCRIPTION02
SERIAL03
STATUS MPX04
ERROR LINK MPX05
TAMPER / INPUT 24H06
POLAR. NA/NC07
TYPELOG/BAL08
MANIP . LINE09
10
SENSIBILITY 1 TO 811
NUM. IMPULS OF 1 TO 412
FUNCTION . LED
13
INSTALLATION
14
AREA
15
FUNCTION
16
INSTALL. COMMAND
17
COMMAND MODE
18
19
GONG IMM.
21
GONG RIT
22
NUM. IMPULS OF 1 TO 8
23
COMMAND LEVEL20
OUTPUT ON BAD MPX27
TIMER IMPULSE (ST/EV)26
LED28
LOGIC OUTPUT29
INVERSE OUTPUT24
TYPE OUTPUT25
MESS.COMMUN.DIGIT.30
ECHO OUTPUT31
Funioni programmbili
per l’uscita
DISCONNECTION01
FUNCTION
CONNECTION02
CONN . / DISCONN .03
CONN . SILENT04
CONN . SIL. / DISC .05
STOP HOLDUP
06
STOP ALARM07
ZONE IMMEDIATE08
ZONE DELAYED09
24H10
NO ONE00
security
XM22K- Console XM with key KEY
817ADE-1.00
DISCONNECTION01
FUNCTION
CONNECTION02
CONN . / DISCONN .03
CONNEC. SILENT04
CONN . SIL. / DISC .05
STOP HOLDUP
06
STOP ALARM07
ZONE IMMEDIATE08
ZONE DELAYED09
24H10
NO ONE00
ENABLING01
PARAMETERS
DESCRIPTION02
SERIAL03
STATUS MPX04
ERROR LINK MPX05
TAMPER / INPUT 24H06
POLAR. NA/NC07
TYPELOG/BAL08
MANIP . LINE09
UNUSED10
SENSIBILITY 1 TO 811
NUM. IMPULS 1 TO 412
FUNCTION . LED
13
INSTALLATION
14
AREA
15
FUNCTION
16
COMMAND INSTALLAT.
17
COMMANDE MODE
18
HOLDUP
19
GONG IM .
21
GONG RIT
22
NUM. IMPULS 1 TO 8
23
COMMANDE LEVEL20
OUTPUT ON BAD MPX27
LED28
START IMPULSE (ST/EV)26
LOGIC OUTPUT29
INVERS. COMMANDE24
OUTPUT TYPE25
ECHO OUTPUT
31
MES. COMMON. DIGIT.
30
Console Table XM22K (Type 04)
The following table shows what are the main functions of Type 04