Hitachi Kokusai Electric KP-F83GV User manual

Gigabit Ethernet
Progressive Scan CCD Camera
KP-F83GV
Specifications (Preliminary) Ver2 4
1. General
The KP-F83GV is single CCD type camera which utilize the progressive scan CCD image
sensor with square pixel for XGA format of 1/3-inch.
By a option of a Gigabit Ethernet interface, high-spee connection of maximum of 1 Gbps can
be possible. Moreover, by using hub or switcher, construction of multiple camera system can
be easily performe .
2. Principal features
1) High resolution
The 1/3-inch 800,000 pixels square lattice progressive scan CCD achieve a high resolution
of 1024(H) x 768(V) (XGA).
2) Gigabit Ethernet interface
High-spee serial interface Gigabit Ethernet supporte an irect connection is possible to
PC by the iameter cable of thin as compare with parallel output. Cable length can be
exten e to maximum 100m without hub an switcher.
3) GigE Vision correspon ence
Base on in ustrial camera interface stan ar GigE Vision, a maximum of 1 Gbps high
spee ata transmit is available an suitable for image processing.
4) CCD rive functions
󲸤Auto electronic Shutter mo e (AES)
A juste automatically from 10 secon to approx. 1/100,000 secon .
󲸤Variable electronic shutter mo e
Variable at 1H steps from 10 secon to approx. 1/100,000 secon .
5) External trigger
An external trigger signal input can be use to capture an image at esire timing for instant
view or processing. The software trigger via a Gigabit Ethernet cable an the har ware
trigger can eal with all trigger signals.

3. Specifications
1) Imaging evice : 1/3-inch progressive scan interline CCD
(with on-chip microlenses)
Total number of pixels : 1077(H) x 788(V)
No. of effective pixels : 1034(H) x 779(V)
Unit cell size : 4.65(H) x 4.65(V) um (Square pixel)
2) Scanning system : Progressive scan
3) Frame rate : 36 fps (for all image format)
4) Sync system : Internal / external
5) Lens mount : C mount
6) Vi eo signal output
Interface : Gigabit Ethernet
Protocol : GigE Vision compliant
Transfer rate : 1 Gbit per secon
Image format : Mono 8/10bit
Image size : 1024(H) x 768(V)
7) External sync signal VD output 5Vp-p plus minus 0.3V
Strobe out 5Vp-p plus minus 0.3V
8) Stan ar sensitivity : 2000lx F5.6
9) Electric shutter spee : Auto (AES) / Manual (VARIABLE)
From 10 secon to approx. 1/100,000 secon
10) External trigger shutter : Mo e Fixe shutter
One trigger
VD Sync
Input Via Gigabit Ethernet cable (Software trigger)
12-pin connector (Har ware trigger)
Input level 5Vp-p plus minus 1V
11) Auto Exposure (ALC: Auto level control)
: A justable for vi eo level
12) Gain : Auto / Manual (0 B to 18 B)
13) Gamma : OFF / ON
14) Sharpness : A justable
15) Brightness : A justable
16) Power supply : DC+12V plus minus 1V
17) Power consumption : Approx. 3.2W (DC+12V)

18) Ambient temperature
Operating : -10 ℃ to +50 ℃ / 30 to 80 %RH
Note : If operate continuously, be sure to use at less than +40 ℃(104F)
for long term stable performance.
Storage : -20 ℃ to +60 ℃ / 20 to 90 %RH
19) Vibration en urance : 68.65 m/s2 or less
(10 to 200Hz, 30 minutes each on XYZ axes)
(Do not subject to strong vibration for long perio s of time.)
20) Shock en urance : 490.3 m/s2 or less (vertical, horizontal, once each face)
21) External imensions : 44(W) x 29(H) x 72(D) mm
(not inclu ing lens an protrusions)
22) Mass : Approx. 140g (without lens)
23) Camera remote : Gigabit Ethernet control
24) Supplie equipment : Camera
CD-ROM (Operation manual / Driver soft)
25) Optional accessories : LAN cable (Enhance category 5 or Category 6)

󲷯󲷫󲷠󲷳󲷤󲷋󲷱󲷠󲷳󲷤󲷣
󲷲󲷤󲷱󲷍󲷭󲷮󲷍
󲷐󲷓.󲷔
󲷴󲷐
󲷓󲷌󲷬󲷒󲷇󲷣󲷤󲷯󲷳󲷧󲷙󲷒.󲷔󲷈
󲷇󲷑󲷈
󲷔.󲷑 󲷖󲷑.󲷏
󲷖󲷖.󲷑
󲷓󲷌󲷬󲷒󲷇󲷣󲷤󲷯󲷳󲷧󲷙󲷒.󲷔󲷈
󲷑󲷐.󲷑 󲷑󲷔
󲷕󲷔.󲷔
󲷗.󲷖
󲷓󲷌󲷬󲷑󲷇󲷣󲷤󲷯󲷳󲷧󲷙󲷒.󲷔󲷈
󲷐󲷒
󲷇󲷕.󲷒󲷈
󲷑󲷘
󲷓󲷓
󲷇φ󲷑󲷖.󲷓󲷈
󲷑󲷔
󲷑󲷕 󲷑󲷕
󲷳󲷤󲷭󲷳󲷠󲷳󲷨󲷵󲷤
󲷴󲷭󲷨󲷳󲷙
󲷲󲷢󲷠󲷫󲷤 󲷙󲷺󲷭󲷳󲷲󲷼
󲸌󲸌

4. Pin assignment
(1) Gigabit Ethernet connector
PIN NO.
Signal
1 TRP1+
2 TPR1-
3 TRP2+
4 TPR3+
5 TRP3-
6 TRP2-
7 TRP4+
8 TRP4-
Connector : RJ-45
(2) 12-pin connector
PIN NO. Signal PIN NO. Signal
1 GND 7 TRIG/VD IN
2 +12V 8 GND
3 GND 9 N.C.
4 N.C. 10 FLASH / VD OUT
5 GND 11 N.C.
6 N.C. 12 GND
Connector (camera si e) : SAMWOO SNH-10-12 (RPCB) or equivalent
Plug (matching cable plug) : Hirose HR10A-10P-12S (01) or equivalent
Please o not unplug an insert cable (camera cable) with a power supplie to a camera.
Install clamp filter (ZCAT 2035-0930A: TDK) at both en s (camera an vi eo processor
en s) in the CE marking legion.
1 9
8
10
2
11 12 73
456

Warranty an service:
1) The guarantee perio is one year after the ata purchase. However, the efects ue to
erroneous use or intentional act are exclu e .
2) As the efect after expiration of the guarantee perio , where pro uct repair is possible,
repair will be performe at charge.
3) The present Warranty pertains only to the camera unit. Secon ary malfunctions
attributable to camera failure as well as expenses incurre by isassembly an
reassembly of the relate system, are beyon the scope of this Warranty.
4) Compensation for loss of business, loss or amage to software, atabase an other
contingent losses are beyon the scope of this Warranty.
5) Hitachi Kokusai Electric Inc. is not liable for the losses cause when the equipment is
use in a system, use for business tra es, pro uction process, me ical fiel s, crime
prevention applications, etc.
6) The parts use in the equipment have their respective lives. The lives of such parts will
be shortene un er the environments of high temperature or high humi ity. When the
stable operation is require for a long time, it is recommen e to perform perio ical
maintenance an inspection every year or every two years.
Notice:
These specifications are subject to change without prior notice ue to pro uct
improvement. Confirm the most recent specifications at time of or er.
Hitachi Kokusai Electric certifies this pro uct complies with the stan ar warranty
con itions of Hitachi Kokusai Electric, an that quality control is implemente to the
extent require to comply with these con itions.