Hitachi VK-S274 User manual

SERVICE MANUAL
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
Digital Media Products Division,Tokai
COLOR & B/W VIDEO CAMERA
2001September
TK No. 8104E
VK-S274/S274E
VK-K274/K274E

CAUTION- 1
Many electrical and mechanical parts have special safety-related characteristics. These are often not evident from visual
inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for a
higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this
Service Manual. Electrical components having such features are identified by marking with a on the schematics and
the parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety
characteristics as the HITACHI recommended replacement one, shown in the parts list in this Service Manual, may create
shock, fire, or other hazards. Product safety is continuously under review and new instructions are issued from time to time.
For the latest information, always consult the current HITACHI Service Manual. A subscription to, or additional copies for,
HITACHI Service Manual may be obtained at a nominal charge from HITACHI SALES CORPORATION.
PRODUCT SAFETY NOTICE
!
Cautions
Microsoft, MS, MS-DOS, Windows and Windows NT are registered trademarks of Microsoft Corporation.
Pentium and Celeron are registered trademarks of Intel Corporation.
Manufactured under license from Dolby Laboratories.
"Dolby" and double-D symbol are trademarks of Dolby Laboratories.
Confidential unpublished works. (C) 1992-1997 Dolby Laboratories Inc. All rights reserved.
IBM is registered trademarks of International Business Machines Corporations.
Other company names and product names listed are trademarks or brand names belonging to each company.
TYPE identification Model name
TYPE S VK-S274
TYPE SE VK-S274E
TYPE K VK-K274
TYPE KE VK-K274E
How to discriminate the "TYPE" identifications in the manual
The parts and circuits are identified by "TYPE" in this manual to discriminate the differences between models. The
TYPE numbers are the same as the model numbers. The table below shows how to read the type identifications.

CAUTION- 2
Notes When Using Service Manual
The following shows the contents to be noted when using service manual:
1. Value units used in parts list
This table shows locations of each part on circuit board
diagrams. The locations are indicated using the guide
scales on the external lines of diagrams.
1) One diagram indicated for each board
The values, dielectric strength (power capacitance) and
tolerances of the resistors (excluding variable resistors)
and capacitors are indicated in the schematic diagrams
using abbreviations.
[Resistors]
Certain symbols are indicated below for value units of
resistors, capacitors and coils in parts list. When you read
them note the following regular indications:
Indication in list Regular indication
KOHM ........................................... k
UF ................................................ µF
PF ................................................ pF
UH ................................................ µH
MH ............................................... mH
Parts
Resistor
Capacitor
Coil
2) Two diagrams indicated for each board
2. Values in schematic diagrams
Item
Value
Tolerance
Power
capacitance
Indication
No indication ...................................
K................................................... k
M.................................................. M
No indication ............................. ±5%
(All tolerances other than ±5% are
indicated in schematic diagrams)
No indication ............................ 1/8W
(1/16W for leadless resistors without
indication)
All capacitances other than the above
are indicated in schematic diagrams.
[Capacitors]
Item
Value
Dielectric
strength
Indication
No indication ................................. µF
P................................................... pF
No indication .............................. 50V
(All dielectric strengths other than 50V
are indicated in schematic diagrams)
Item
Value
Indication
µ.................................................... µH
m.................................................. mH
[Coils]
3. Identifications of sides A/B in
circuit board diagrams
1) Board having a pattern on one side and parts on both
sides.
Side A: Shows discrete parts, viewed from the pattern
side.
Side B: Shows leadless parts, viewed from the
pattern side.
2) Board having patterns on both sides and parts on
both sides.
Side A: Shows parts and patterns which can be seen
when the case is opened.
Side B: Shows parts and the pattern on the back of
side A.
4. Table for indexing locations of parts
Parts
Location
2 A
Symbol
No.
IC
IC1201
Type of part
Zone "A" on board diagram
Circuit No. Zone "2" on board diagram
Parts
Location
A - 2 A
Symbol
No.
IC
IC1201
Zone "2" on board
diagram
A: Shows side A
B: Shows side B
Zone "A" on board
diagram
Type of
part
Circuit No.

CHAPTER 1 GENERAL INFORMATION
1. Specifications .........................................................1-1
2. Comparison with Previous Model ..........................1-2
2.1 Comparison of Specifications .........................1-2
2.2 Comparison of ICs ..........................................1-2
CHAPTER 2 DISASSEMBLY
1. Procedure ..............................................................2-1
CHAPTER 3 ELECTRIC CIRCUIT
ADJUSTMENT
1. Test Equipment/Jigs Necessary for Adjustment ....3-1
1.1 List of Equipment and Jigs ..............................3-1
1.2 List of Charts for Adjustment ...........................3-1
1.3 Test Equipment, etc. ....................................... 3-1
2. Before Stating Adjustment .....................................3-2
2.1 Connections for Adjustment ............................3-2
2.2 Notes ...............................................................3-2
2.3 Setting Test Equipment ...................................3-3
3. List of Adjustment Items.........................................3-4
4. Starting Adjustment Program (SMAP) ...................3-5
5. Data Initilize Procedure ..........................................3-6
5.1 Data Initilize .....................................................3-6
6. Electronic Volume Adjustment Procedure .............3-7
6.1 CDS Sampling Pulse Adjustment ...................3-7
7. Camera Adjustment (Adjustment) Procedure ........3-8
7.1 Auto Iris Control Adjustment ...........................3-8
7.2 Matrix Adjustment [For TYPE S/SE] ...............3-8
7.3 White Balance Adjustment [For TYPE S/SE] ..3-9
7.4 Chroma Gain Adjustment [For TYPE S/SE] .... 3-10
8. Autofocus Adjustment Procedure ..........................3-11
8.1 Zoom/Focus Tracking Adjustment ..................3-11
8.2 AF Noise Level Adjustment .............................3-12
8.3 Check of Zoom Trace......................................3-12
9. Spot Noise Adjustment Procedure.........................3-13
9.1 Spot noise Adjustment ....................................3-13
10. Error Messages......................................................3-14
10.1 Error massage of Electronic Volume and
Camera Adjustment ........................................3-14
10.2 Error massage of Autofocus Adjustment .......3-15
10.3 Error massage of Spot Noise Adjustment ......3-15
10.4 Troubleshooting of Autofocus ......................... 3-16
(1) No zoom and focus operation .......................3-16
(2) No focus lens operation ................................ 3-18
(3) No zoom operation .......................................3-19
(4) No autofocus operation.................................3-20
(5) Subject is greatly out-of-focus
when zoomed................................................3-21
CONTENTS-1
CHAPTER 4 EXPLODED VIEW
1. Exploded View .......................................................4-1
CHAPTER 5 REPLACEMENT
PARTS LIST
1. Mechanical Parts List ............................................. 5-1
2. Electrical Parts List ................................................5-2
CHAPTER 6 SCHEMATIC, CIRCUIT
BOARD AND BLOCK
DIAGRAMS/MICROPRO
CESSOR PIN FUNCTION
TABLES
Schematic Diagrams
Connection Diagram ....................................................6-1
Waveforms...................................................................6-1
Sensor [SP]..................................................................6-2
Process [PC] (For Display) ..........................................6-3
Process [PC] (For Printing) <A-a> ...............................6-4
Process [PC] (For Printing) <A-b> ...............................6-5
Switching Regulator [CSR] ..........................................6-6
Circuit Board Diagrams
PC -Side A/B- ..............................................................6-9
Identification of Parts Location...............................6-7
SP -Side A/B-...............................................................6-10
Identification of Parts Location...............................6-7
CSR -Side A/B- ............................................................6-10
Identification of Parts Location...............................6-8
Block Diagrams
Overall .........................................................................6-11
Microprocessor Pin Function Tables
Digital Microprocessor (IC1201: D-µP) ........................ 6-12
Contents

1 - 1
CHAPTER 1 GENERAL INFORMATION
Note: The specifications are subject to change for improvement without notice.
Signal VK-S274: NTSC Format
VK-S274E: PAL Format
VK-K274: EIA Format
VK-K274E: CCIR Format
Scanning System 2:1 Interlaced
Image Sensor 4.5 mm Dia. (1/4-inch) CCD Image Sensor
Number of Effective Pixels VK-S274/K274: 380 k [786 (H) × 494 (V)]
VK-S274E/K274E: 440 k [752 (H) × 582 (V)]
Total Number of Pixels VK-S274/K274: 410 k [811 (H) × 508 (V)]
VK-S274E/K274E: 470 k [795 (H) × 596 (V)]
Scanning Frequency VK-S274/K274: Horizontal 15.734 kHz
Vertical 59.94 Hz
VK-S274E/K274E: Horizontal 15.625 kHz
Vertical 50 Hz
Lens F1.6 to 3.8 (4 to 88 mm) 22 : 1 power zoom lens with autofocus
Video Signal Output VK-S274/S274E: Composite Signal 1.0 Vp-p
VK-K274/K274E: Y (Luminance) Signal 1.0 Vp-p
Minimum Required Illumination VK-S274/S274E: Standard 1.0 lx
DS shutter 0.1 lx
VK-K274/K274E: Standard 0.1 lx
DS shutter 0.01 lx
S/N Ratio 50 dB or more
Horizontal Resolution 470 TV Line or more
Operating Temperature 0 to 60 °C
Operating Humidity 10 to 90 %
Power Input DC 9 V ± 0.5 V
Power Consumption 3.3 W or less
Dimensions 50 (W) × 60 (H) × 89.5 (D) mm
Weight Approx. 225 g
1. Specifications

1 - 2
ITEM
Signal Format
Power Requirements
Power Consumption
Dimensions (W × H × D mm)
Weight
Lens
Operating Temperature/Humidity
Image Sensor
Number of Effective Pixels
Total Number of Pixels
Scanning System
Horizontal Scanning Frequency
Vertical Scanning Frequency
Sync Format
Video Signal Output
S/N Ratio
Horizontal Resolution
Minimum Required Illumination
(Standard)
IR cf Mode
ITEM
CCD Sensor
Sensor Drive (or Drive Pulse Gen.)
CDS AGC & A/D CONV.
Camera Digital Signal Processor (DSP)
DRAM
Inv.
Clock Generator (or Inv.)
Camera (or Digital) µP
EEPROM
Reset Pulse Gen.
Zoom Motor Drive
Focus Motor Drive
F.Det./Iris Drive
PWM
Y/C Mix. & Video Amp
Level Shift
VCO/Phase Compa.
FV Pulse Gen.
VK-S274/VK-S274E
VK-K274/VK-K274E
VK-S274: NTSC
VK-S274E: PAL
VK-K274: EIA
VK-K274E: CCIR
DC 9 V
3.3 W (MAX)
50 × 60 × 89.5
Approx. 225 g
Power zoom × 22 (4.0 - 88.0 mm)
F 1.6
0 °C to 60 °C (Recommendation: 0 °C to 40 °C)
10 % to 90 %
4.5mm Dia. (1/4 inch) CCD
VK-S274/K274: 786 (H) × 494 (V)
VK-S274E/K274E: 752 (H) × 582 (V)
VK-S274/K274: 811 (H) × 508 (V)
VK-S274E/K274E: 795 (H) × 596 (V)
2 : 1 Interlaced
VK-S274/K274: 15.734 kHz
VK-S274E/K274E: 15.625 kHz
VK-S274/K274: 59.94 Hz
VK-S274E/K274E: 50 Hz
Internal/External
VK-S274/S274E:
Composite Signal 1.0 Vp-p
VK-K274/K274E:
Y (Luminance) Signal 1.0Vp-p
50 dB or more
470 TV Line or more
VK-S274/S274E: 1.0 lx
VK-K274/K274E: 0.1 lx
Not Provided
VK-S274/VK-S274E
VK-K274/VK-K274E
VK-S274: ICX278AK-L (IC1001)
VK-S274E: ICX279AK-L (IC1001)
VK-K274: ICX278AL-7 (IC1001)
VK-K274E: ICX279AL-7 (IC1001)
µPD16510GR (IC1002)
HD49323AF (IC1101)
HG73C053FE (IC1121)
MSM51V18165F (IC1122)
TC7SU04FU (IC1173)
TC7SHU04FUL (IC1174)
HD64F2238AFA13-S274 (IC1201)
X25097V1-2.7 (IC1202)
RN5VD27AA (IC1203)
TC7SH14FU (IC1204/IC1205)
TC7S08FU (IC1206)
MPC17AT85VM (IC1301)
MPC17AT85VM (IC1302)
µPD5023GS-147-GJG (IC1351)
TL1464IPT (IC1501)
BA7664FV (IC1601)
HD74HCT125T (IC1602)
74VHC4046MTCX (IC1603)
IDC-7S08 (IC1604)
2.2 Comparison of ICs
2.1 Comparison of Specifications
2. Comparison with Previous Model
VK-S234/VK-S234E
VK-K234/VK-K234E
VK-S234: NTSC
VK-S234E: PAL
VK-K234: EIA
VK-K234E: CCIR
VK-S234/K234: 768 (H) × 494 (V)
VK-S234E/K274E: 752 (H) × 582 (V)
VK-S234/K234: 811 (H) × 508 (V)
VK-S234E/K234E: 795 (H) × 596 (V)
VK-S234/K234: 15.734 kHz
VK-S234E/K234E: 15.625 kHz
VK-S234/K234: 59.94 Hz
VK-S234E/K324E: 50 Hz
VK-S234/S234E:
Composite Signal 1.0 Vp-p
VK-K234/K234E:
Y (Luminance) Signal 1.0Vp-p
46 dB or more
VK-S234: 470 TV Line or more
VK-S234E: 460 TV Line or more
VK-K234/K234E: 500 TV Line or more
VK-S234/S234E: 3.0 lx
VK-K234/K234E: 0.1 lx
VK-S234/VK-S234E
VK-K234/VK-K234E
VK-S234: ICX208AK-6 (IC1001)
VK-S234E: ICX209AK-6 (IC1001)
VK-K234: ICX208AL-6 (IC1001)
VK-K234E: ICX209AL-6 (IC1001)
TC7SHU04F (IC1173)
TC7SU04F (IC1174)
HD6432237M (IC1201)
RN5VT28AA (IC1203)
TC7SH14FU (IC1204/IC1205)

2 - 1
CHAPTER 2 DISASSEMBLY
Fig. 2-1-1
(1) Release the lock of the connector
on the left and right.
(2) Pull out the flat cable
Fig. 2-1-2
*1 : Do not the pull out the flat cable or touch the exposed
terminal at the connecting position with your bare
hands as it could cause a defective (1) and (2) shown
in Fig. 2-1-2.
*2 : When the SP circuit board is removed, the crystal filter
and rubber are also removed.
Be careful not to damege and lose them.
1. Procedure
SP
CIRCUIT
BOARD CSR
CIRCUIT
BOARD
PC CIRCUIT
BOARD
B
A
B
A
D
C
D
C
CHASSIS (R)
(1) REMOVE
TWO
SCREWS
(2) REMOVE
TWO
SCREWS
(3) REMOVE
TWO
SCREWS
CHASSIS (L)
(4) DISCONNECT
FLAT CABLE
(*1)
(5) REMOVE ONE SCREW
(6) REMOVE THE
PC CIRCUIT
BOARD
(7) REMOVE
ONE
SCREW
(8) REMOVE
THE CSR
CIRCUIT
BOARD
(9) REMOVE TWO
SCREWS
(*2)
(10) REMOVE
TWO
SCREWS
CCD
SENSOR
RUBBER
CRYSTAL
FILTER
LENS
BLOCK
CAMERA
CHASSIS
(11) REMOVE
TWO
SCREWS
(12) REMOVE
ONE
SCREW
(1)
(1) (2)

3 - 1
CHAPTER 3 ELECTRIC CIRCUIT ADJUSTMENT
1. Test Equipment/Jigs Necessary for Adjustment
1.1 List of Equipment and Jigs
1.2 List of Charts for Adjustment
1.3 Test Equipment, etc.
Color video monitor (color TV for monitoring)
Oscilloscope
Vectorscope [If not available, adjustment is still possible, but easier if this is used]
Digital voltmeter (DVM)
3100 K light box
DC power supply (9 V/3 A) [To power of video camera]
DC power supply (5 V/1 A) [To power of DSP-R jig]
*1 : The adjustment floppy disk is not for sale: It will be
supplied only when service maintenance contract
is concluded.
DSP-R Jig
No.7099448
C12 Light Balancing Filter
No.7099369
Personal Computer (PC)
[Goods on the Market]
Personal Computer Cable
RS-232C (9 or 25 pins)
Straight Type
[Goods on the Market]
New
Adjutsment Floppy
Disk (
*1 )
DSP Interface Connect Jig
No. 7069179
Color Bar Chart Gray Scale Chart Backfocus Chart

3 - 2
2. Before Starting Adjustment
2.1 Connections for Adjustment
Connect the video camera to the test equipment and jigs as shown in Fig. 2-1.
Fig. 2-1
PG1601
VIDEO CAMERA
LIGHT
BOX
9PIN FLAT CABLE
(ACCESSORY)
COLOR VIDEO
MONITOR
VIDEO IN
19
DSP INTERFACE CONNECT JIG
123456789
RD WHT
SD BRW
GND BRW
+B BRW
GND BRW
VIDEO BRW
GND(VIDEO) BRW
EX. FV BRW
GND BRW
1
2
3
4
5
6
7
8
9
+
DC POWER
SUPPLY
(9V/3A)
GND
+
DC POWER
SUPPLY
(5V/1A)
GND
PERSONAL
COMPUTER
PERSONAL
COMPUTER
CABLE (RS-232C)
DSP-R JIG
BLK
RED
BLK
WHT
YEL
2.2 Notes
1) All adjustments are performed using the adjustment program and personal computer (PC). The adjustment program is
subject to change without notice for improvements in functions and operability, and the actual instructions on PC screen
may be different from those in this manual: If so, follow the instructions on PC screen to proceed with adjustment.
2) Since this chapter uses the device with the highest performance among the models listed to explain adjustment, the actual
instructions on PC screen may be different from those in this manual, depending on whether some functions are provided
or not: If so, follow the instructions on PC screen to proceed with adjustment.
3) The adjustment program will not operate normally unless the video camera, PC and test equipment/jigs are all turned on.

3 - 3
4) Be sure to connect the video output of video camera to a color video monitor (terminate the video output with 75 ohm:
If the video output is not connected to the monitor (and if it is not terminated with 75 ohm), the output video signal level
cannot be measured correctly.
5) Use light box that does not flicker and whose color temperature is controlled, for adjustment. If an inappropriate light box is
used, precise adjustment will not be possible, and the adjustment program will not operate normally.
6) Take care with the following when pointing the video camera at a chart (light box):
Focus the chart correctly.
Set the chart (light box) 30-50 cm away from the lens surface, and avoid any effects from surrounding light (except for
a case where some designation is given).
Aim at the chart and let chart fill the screen (video period). (Except for a case where some designation is given.)
2.3 Setting Test Equipment
1) Set the switches, knobs and each mode of oscilloscope as follows for adjustment:
Probe: 10:1
TIME/DIV: 10 or 20 µs (except for a case where some designation is given)
VOLTS/DIV: Will vary depending on the measurement object (except for a case where some designation is
given)
Synchronization: Internal sync (except for a case where some designation is given)
AC/DC/GND: AC (except for a case where some designation is given)
Note: The names of switches, knobs, modes, etc. of oscilloscope may vary slightly depending on the manufacturer or
model. Since some oscilloscopes may have switches, etc. other than the above that must be set, see the instruction
manual of the particular oscilloscope for details.

3 - 4
3. List of Adjustment Items
The following table shows the adjustment items, their purposes, and whether or not check is required after replacing major
components.
The components shown in the table below are the minimum to be checked after replacing major components: If several
components have been replaced - or depending on the cause of a defect - more components may need to be checked.
: CHECK
*1: When replacing the PC circuit board (containing EEPROM) or EEPROM, be sure to perform all adjustments
only after "Data Initialize".
*2: Since all adjustments must be performed any time "Data Initialize" is done, do not perform it indiscriminately.
*3: For the color video camera (TYPE S/SE).
Circuit Boards
SP
Electrical Parts
IC1001 IC1101 IC1201 IC1250
(*1)
Other
Lens Block
Data Initialize
Data Initilize (*2)
Electric Volume
CDS Sampling Pulse
Camera Adjustment (Adjustment)
Initilizing EEPROM.
To suppress noise in the CCD sensor
output signal and maximize the signal
level.
PC
(*1)
IC1351
Items Purpose Adjustment
Auto Iris
White Balance (*3)
Chroma Gain (*3)
To set the iris control data.
To input the automatic white balance
control data.
To set the color satuation under the
reference color temperrature.
Auto Focus
Spot Noise
Zoom/Focus Tracking
AF Noise Level
Check of Zoom Trace
Spot Noise
To set the out-of -focus correction level
during zooming.
To set the noise level in the autofocus
circuit.
To check the autofocus adjustment.
To correct spot noise.
Matrix (*3) To compensate for uneveness in the
chroma signal

3 - 5
Referrence
Misoperation message
MS-DOS screen-2
SMAP input screen
Model select screen
Screen for verifying model name
Main menu
4. Starting Adjustment Program (SMAP)
C>A:
A>
C>A:
A>SMAP_IBM 1
***********************************************************
MODEL SELECT
***********************************************************
[1] ××××××××
[2] ××××××××
[3] ××××××××
[4] ××××××××
[5] ××××××××
[P] NEXT SELECTION
[ESC] END
Please select the type of the set
Press [1] - [5] or [P] or [ESC]
Selected model is ××××××××
Are you sure ? (Y/N)
CAN NOT FIND THE DATA FILE
**** PRESS ANY KEY ****
***********************************************************
MANUAL ADJUSTMENT PROGRAM
***********************************************************
[A] DATA INITIALIZE
[B] ELECTRIC VOLUME
[C] ADJUSTMENT
[D] AUTO FOCUS
[E] SPOT NOISE
[ESC] END
Please select [A] - [F] or [ESC]
Note: If error message appears during adjustment, refer to "10. Error Messages".
1) Connect the video camera, DSP-R jig and PC as shown in Fig. 2-1, and supply
power to them. (*1)
2) Operate the PC to start MS-DOS . (*2)
3) Make sure that the adjustment floppy disk is write-protected.
4) Insert the adjustment floppy disk into the floppy disk drive of PC.
5) Use the PC keyboard to type A: and press Enter key. (*3) (See the MS-DOS
screen-1 and 2)
6) Type SMAP_IBM (space) 1 and press Enter key. (*4) (See the SMAP input
screen)
7) The SMAP will start: Make sure that the model select screen appears on the
PC display. (*5) (See the model select screen)
8) If the appropriate model is displayed on the model select screen, input the
number to PC. If the appropriate model name is not shown on the model select
screen, input Pto PC until the model name appears. (*6)
9) The screen for verifying the model name will appear on PC display: If it is
correct, input Yto PC. If it is incorrect, input Nand start over (from step 8).
10)Make sure that the main menu appears on PC display: If it does not appear,
check whether model selection (in step 8) is correct.
*1: If the connection of jig, etc. is inappropriate or power is not supplied, the
adjustment program will not start normally.
*2: For details on how to start MS-DOS, refer to the instruction manual of PC,
since this varies for each PC.
*3: The letter to be input is to designate the drive into which the adjustment
floppy disk has been inserted. If using a drive other than A, designate the
drive.
*4: The number to be input after a space is to designate the serial port no. of
PC. If the PC has two or more serial ports, and the DSP-R jig is connected
to a port other than serial port 1, input the serial port number.
*5: If the model select screen does not appear, make sure of the following:
Power is supplied to the video camera and DSP-R jig.
The designation of drive (in step 5) is correct.
The designation of serial port is correct.
The correct adjustment floppy disk has been correctly inserted.
*6: If an erroneous model name or number is selected, misoperation message
will appear on PC display: Press any key to restore the model select
screen.
To terminate the adjustment program (SMAP):
Press the Esc key once to three times until the PC display returns from
each menu screen to the MS-DOS screen.
When the MS-DOS screen appears on PC display, turn off the video camera
and jig.
C>
MS-DOS screen-1
Press Enter key.
Type SMAP_IBM 1.
Model select (Input the number).
Input Y.
R
R

3 - 6
Main menu
Screen for verifying initialization
5. Data Initialize Procedure
The following explains the adjustment procedure using the adjustment program (SMAP), following the order of items on PC
display.
Refer to "4. Starting Adjustment Program (SMAP)" in advance, start SMAP and display the main menu on PC display.
In actual work, it is possible to adjust one item independently.
Note: If error message appears on PC display during adjustment, perform troubleshooting, referring to "10. Error Messages".
***********************************************************
MANUAL ADJUSTMENT PROGRAM
***********************************************************
[A] DATA INITIALIZE
[B] ELECTRIC VOLUME
[C] ADJUSTMENT
[D] AUTO FOCUS
[E] SPOT NOISE
[ESC] END
Please select [A] - [F] or [ESC]
<< DATA WRITING >>
START TO SEND DATA. (Y/N)
5.1 Data Initialize
This procedure initializes the data in EEPROM (including the adjustment data).
Any time you replace the PC circuit board (containing EEPROM) or EEPROM, be
sure to perform this procedure. [Generally, this procedure is not necessary after
replacing other circuit board (components).]
Important:
After completing this adjustment, be sure to perform all adjustment items as
follows.
Procedure:
1) Input Ato PC on the main menu screen.
2) The screen for verifying the initialization will appear: Input Yto PC. (*1)
3) Follow the instructions on PC display thereafter.
*1: Entering Non the screen for verifying initialization will restore the
data main menu screen.
Input A.
Input Y.
Follow the instructions on PC display
thereafter.

3 - 7
***********************************************************
ELECTRIC VOLUME
***********************************************************
[1] CDS SAMPLING PULSE
[ESC] RETURN TO MAIN MENU
Please select [1] or [ESC]
Electronic volume menu
Main menu
***********************************************************
MANUAL ADJUSTMENT PROGRAM
***********************************************************
[A] DATA INITIALIZE
[B] ELECTRIC VOLUME
[C] ADJUSTMENT
[D] AUTO FOCUS
[E] SPOT NOISE
[ESC] END
Please select [A] - [F] or [ESC]
Input B.
6. Electronic Volume Adjustment Procedure
The following explains the adjustment procedure using the adjustment program (SMAP), following the order of items on PC
display.
Refer to "4. Starting Adjustment Program (SMAP)" in advance, start SMAP and display the main menu on PC display.
In actual work, it is possible to adjust one item independently.
Note: If error message appears on PC display during adjustment, perform troubleshooting, referring to "10. Error Messages".
Before starting:
1) Input Bto PC on the main menu screen to display the electronic volume
menu screen. (*1)
*1: Pressing the Esc key on the adjustment menu screen will restore the
main menu screen.
6.1 CDS Sampling Pulse Adjustment
Incompleted Phenomenon:
Diagonal beats and horizontal noise occur.
Condition:
Leave the video camera for more than 2 minutes until the circuits are
stabilized after turing it on, then start adjustment.
Procedure:
1) Input 1to PC on the adjustment menu screen.
2) Follow the instruction on PC display thereafter.
***********************************************************
ELECTRIC VOLUME
***********************************************************
[1] CDS SAMPLING PULSE
[ESC] RETURN TO MAIN MENU
Please select [1] or [ESC]
Electronic volume menu
Input 1.
Follow the instructions on PC display
thereafter.

3 - 8
7. Camera Adjustment (Adjustment) Procedure
Main menu
***********************************************************
MANUAL ADJUSTMENT PROGRAM
***********************************************************
[A] DATA INITIALIZE
[B] ELECTRIC VOLUME
[C] ADJUSTMENT
[D] AUTO FOCUS
[E] SPOT NOISE
[ESC] END
Please select [A] - [F] or [ESC]
***********************************************************
ADJUSTMENT
***********************************************************
[1] AUTO IRIS CONTROL
[2] MATRIX
[3] WHITE BALANCE
[4] CHROMA GAIN
[ESC] RETURN TO MAIN MENU
Please select [1] - [3] or [ESC]
Adjustment menu
ADJUSTMENT FINISHED
PRESS ANY KEY
AIC adjustment complete
Input C.
***********************************************************
ADJUSTMENT
***********************************************************
[1] AUTO IRIS CONTROL
[2] MATRIX
[3] WHITE BALANCE
[4] CHROMA GAIN
[ESC] RETURN TO MAIN MENU
Please select [1] - [3] or [ESC]
Adjustment menu
Input 1.
Follow the instructions on PC display
thereafter.
The following explains the adjustment procedure using the adjustment program
(SMAP), following the order of items on PC display.
Refer to "4. Starting Adjustment Program (SMAP)" in advance, start SMAP and
display the main menu on PC display.
In actual work, it is possible to adjust one item independently.
Note: If error message appears on PC display during adjustment, perform
troubleshooting, referring to "10. Error Messages".
Before starting:
1) Input Cto PC on the main menu screen to display the adjustment menu
screen.
2) Input to PC the appropriate adjustment number. (*1)
*1: Pressing the Esc key on the adjustment menu screen will restore
the main menu screen.
7.1 Auto Iris Control Adjustment
Incompleted Phenomenon:
The picture becomes too bright.
The picture becomes too dark.
Condition:
Set the zoom to wide end and point at the light box, without chart inserted, to
fill the screen.
Procedure:
1) Input 1to PC on the adjustment menu screen.
2) Follow the instruction on PC display thereafter.
3) After the AIC (auto iris control) adjustment complete screen appears,
press any key to restore the adjustment menu screen.
4) Turn the video camera off, leave as is for at least 5 seconds, and then
turn it on again. (*1)
*1: When the video camera is turned on again, the SMAP may not
operate normally, and the following adjustments may not be possible.
If this happens, press the Esc key to restore the MS-DOS screen,
and then restart the SMAP.
7.2 Matrix Adjustment [For TYPE S/SE] (Fig. 7-1)
Incompleted Phenomenon:
Color reproduction becomes defective.
Test Point:
Video Out (PG1601-6)
Equipment/Jig:
Oscilloscope
Conditions:
Point at a color bar chart.
Press any key.
Turn the video camera off.
***********************************************************
ADJUSTMENT
***********************************************************
[1] AUTO IRIS CONTROL
[2] MATRIX
[3] WHITE BALANCE
[4] CHROMA GAIN
[ESC] RETURN TO MAIN MENU
Please select [1] - [3] or [ESC]
Adjustment menu
Input 2.

3 - 9
Procedure:
1) Input 2to PC on the adjustment menu screen.
2) The matrix adjustment screen will appear.
3) Press the Dkey to minimize the yellow (YEL) level.
Press the U key so the ratio between yellow (YEL) and blue (BLU) levels
is 1:4.
Press the Ctrl key and hold it down, then press the Uand D keys so the
ratio between yellow (YEL) and blue (BLU) levels is 1:4.
4) Press the Enter key: The PC display will switch from the matrix data write
screen to matrix adjustment complete screen.
5) Press any key to restore the adjustment menu screen.
<< ADJUSTMENT OF BLUE MATRIX >>
ROUGH ADJUSTMENT
FINE ADJUSTMENT
[Crt] + [U] UP
[Crt] + [D] DOWN
[ENTER] SAVE & RETURN TO MENU
[ESC] QUIT
[U] UP
[D] DOWN
Matrix adjustment
Matrix data write
Set the ratio between yellow (YEL) and blue
(BLU) levels is 1:4.
Matrix adjustment complete
Press Enter key.
Press any key.
<< ADJUSTMENT OF BLUE MATRIX >>
DATA WRITING INTO EEPROM
<< ADJUSTMENT OF BLUE MATRIX >>
ADJUSTMENT FINISHED
PRESS ANY KEY
7.3 White Balance Adjustment [For TYPE S/SE]
Incompleted Phenomenon:
Color of the subject is different from that of the picture.
A white subject is not seen as white.
Equipment/Jig:
C12 light balance filter
Conditions:
Attach a C12 light balance filter to lens.
Set the zoom to wide end, and point at a gray scale chart.
Procedure:
1) Input 3to PC on the adjustment menu screen.
2) Follow the instructions on PC display thereafter.
3) After the white balance adjustment complete screen appears, press any
key to restore the adjustment menu screen.
Fig. 7-1
BLUE (BLU)
YELLOW (YEL)
BLU : YEL
1 : 4
***********************************************************
ADJUSTMENT
***********************************************************
[1] AUTO IRIS CONTROL
[2] MATRIX
[3] WHITE BALANCE
[4] CHROMA GAIN
[ESC] RETURN TO MAIN MENU
Please select [1] - [3] or [ESC]
Adjustment menu
Input 3.
Follow the instructions on PC display
thereafter.
<< ADJUSTMENT OF WHITE BALANCE >>
ADJUSTMENT FINISHED
PRESS ANY KEY
White balance adjustment complete
Press any key.

3 - 10
7.4 Chroma Gain Adjustment [For TYPE S/SE] (Figs. 7-2, 7-3, 7-4)
Incompleted Phenomenon:
Color of the picture is denser than that of the subject.
Color of the picture is lighter than that of the subject.
Test Point:
Video Out (PG1601-6)
Equipment/Jig:
Oscilloscope or Vectorscope
C12 light balance filter
Condition:
Attach a C12 light balance filter to lens
Point the at a color bar chart.
Procedure:
1) Input 4to PC on the adjustment menu screen.
2) The chroma gain adjustment screen will appear.
3)
When using an oscilloscope (Fig. 7-2):
Press the Dor Ukey to set the red level on waveform to approx. 620
mVp-p.
Then, while holding down the Ctrl key, press the Dor Ukey to set the
red level on waveform to approx. 620 mV ± 20 mVp-p.
When using a vectorscope (Figs. 7-3, 7-4):
Press the Dor Ukey to set the red vector to approx. 220% of burst
vector.
Then, while holding down the Ctrl key, press the Dor Ukey to set the
red vector to approx. 220% ± 5% of burst vector.
4) Press the Enter key: The PC display will switch from the chroma gain data
write screen to chroma gain adjustment complete screen.
5) Press any key to restore the adjustment menu screen.
Chroma gain adjustment
***********************************************************
ADJUSTMENT
***********************************************************
[1] AUTO IRIS CONTROL
[2] MATRIX
[3] WHITE BALANCE
[4] CHROMA GAIN
[ESC] RETURN TO MAIN MENU
Please select [1] - [3] or [ESC]
Adjustment menu
<< ADJUSTMENT OF CHROMA GAIN >>
ROUGH ADJUSTMENT
FINE ADJUSTMENT
[Crt] + [U] CHROMA GAIN UP
[Crt] + [D] CHROMA GAIN DOWN
[ENTER] SAVE & RETURN TO MENU
[ESC] QUIT
[U] CHROMA GAIN UP
[D] CHROMA GAIN DOWN
<< ADJUSTMENT OF CHROMA GAIN >>
DATA WRITING INTO EEPROM
Chroma gain data write
<< ADJUSTMENT OF CHROMA GAIN >>
ADJUSTMENT FINISHED
PRESS ANY KEY
Chroma gain adjustment complete
Input 4.
When using an oscilloscope
Set the red level on waveform to 620 mV
± 20 mVp-p.
When using a vectorscope
Set the red vector to 220 % ± 5 % of
burst vector.
Press Enter key.
Press any key.
RED
620 mV
± 20 mV
Fig. 7-2
Fig. 7-3 [For TYPE S] Fig. 7-4 [For TYPE SE]
RED
220 %
± 5 %
BURST
100 %
RED
220 %
± 5 %
BURST
100 %

3 - 11
8.1 Zoom/Focus Tracking Adjustment
Incompleted Phenomenon:
Focus is lost during zooming.
Condition:
Point at the backfocus chart, 1500 ± 5mm away from the lens surface.
Light the backfocus chart with 200 - 400 lx.
Caution when Adjustment:
1) Measure the distance between the chart and lens surface precisely.
2) Place the chart as parallel as possible to the lens surface.
3) The backfocus chart should always be at the center of the monitor screen
when the zoom is set to the wide-angle and telephoto ends.
4) The zoom trace adjustment procedure is completed within 2 minutes after
it is selected.
5) Do not place any obstruction between the lens and chart during
adjustment.
Procedure:
1) Input 1to PC on the AF menu screen.
2) Follow the instructions on PC display thereafter.
Main menu
***********************************************************
MANUAL ADJUSTMENT PROGRAM
***********************************************************
[A] DATA INITIALIZE
[B] ELECTRIC VOLUME
[C] ADJUSTMENT
[D] AUTO FOCUS
[E] SPOT NOISE
[ESC] END
Please select [A] - [F] or [ESC]
***********************************************************
AUTO FOCUS ADJUSTMENT
***********************************************************
[1] ADJUSTMENT OF ZOOM/FOCUS TRACKING
[2] ADJUSTMENT OF AF NOISE LEVEL
[3] CHECK OF ZOOM TRACE
[ESC] RETURN TO MENU
Please select [1] - [3] or [ESC]
AF menu
Input D.
***********************************************************
AUTO FOCUS ADJUSTMENT
***********************************************************
[1] ADJUSTMENT OF ZOOM/FOCUS TRACKING
[2] ADJUSTMENT OF AF NOISE LEVEL
[3] CHECK OF ZOOM TRACE
[ESC] RETURN TO MENU
Please select [1] - [3] or [ESC]
AF menu
Input 1.
Follow the instructions on PC display
thereafter.
8. Autofocus Adjustment Procedure
The following explains the adjustment procedure using the adjustment program (SMAP), following the order of items on PC
display.
Refer to "4. Starting Adjustment Program (SMAP)" in advance, start SMAP and display the main menu on PC display.
In actual work, it is possible to adjust one item independently.
Note: If error message appears on PC display during adjustment, perform troubleshooting, referring to "10. Error Messages".
Before starting adjustment:
1) Input Dto PC on the main menu screen to display the AF menu screen.
2) Input the appropriate adjustment number to PC. (*1)
*1: Pressing the Esc key on the AF menu screen will restore the main
menu screen.

3 - 12
***********************************************************
AUTO FOCUS ADJUSTMENT
***********************************************************
[1] ADJUSTMENT OF ZOOM/FOCUS TRACKING
[2] ADJUSTMENT OF AF NOISE LEVEL
[3] CHECK OF ZOOM TRACE
[ESC] RETURN TO MENU
Please select [1] - [3] or [ESC]
AF menu
Input 3.
Follow the instructions on PC display
thereafter.
8.2 AF Noise Level Adjustment
Incompleted Phenomenon:
It takes time until a subject is brought into focus.
Correct focus is not obtained.
Condition:
Point at a light box without a chart inserted at a distance of up to 10cm.
Caution when Adjustment:
1) Place the light box as parallel as possible to the lens surface.
2) The AF noise level adjustment procedure will be completed within thirty
seconds after it is selected.
Procedure:
1) Input 2to PC on the AF menu screen.
2) Follow the instructions on PC display thereafter.
8.3 Check of Zoom Trace
Incompleted Phenomenon:
Focus is lost during zooming.
Condition:
Point at the backfocus chart, 1500 ± 5mm away from the lens surface.
Light the backfocus chart with 200 - 400 lx.
Caution when Adjustment:
1) Measure the distance between the chart and lens surface precisely.
2) Place the chart as parallel as possible to the lens surface.
3) The backfocus chart should always be at the center of the monitor screen
when the zoom is set to the wide-angle and telephoto ends.
4) Do not place any obstruction between the lens and chart during
adjustment.
Procedure:
1) Input 3to PC on the AF menu screen.
2) Follow the instructions on PC display thereafter.
If error message appears, readjust the following items:
8.1 Zoom/Focus Tracking Adjustment
8.2 AF Noise Level Adjustment
***********************************************************
AUTO FOCUS ADJUSTMENT
***********************************************************
[1] ADJUSTMENT OF ZOOM/FOCUS TRACKING
[2] ADJUSTMENT OF AF NOISE LEVEL
[3] CHECK OF ZOOM TRACE
[ESC] RETURN TO MENU
Please select [1] - [3] or [ESC]
AF menu
Input 2.
Follow the instructions on PC display
thereafter.

3 - 13
<< DATA WRITING >>
START TO SEND DATA. (Y/N)
Screen for verifying writing of spot noise data
FINISHED WRITING DATA
PRESS ANY KEY
Spot noise data write complete
Input Y.
9. Spot Noise Adjustment Procedure
The following explains the adjustment procedure using the adjustment program (SMAP), following the order of items on PC
display.
Refer to "4. Starting Adjustment Program (SMAP)" in advance, start SMAP and display the main menu on PC display.
In actual work, it is possible to adjust one item independently.
Note: If error message appears on PC display during adjustment, perform troubleshooting, referring to "10. Error Messages".
Important:
Spot noise refers to bright points that appear on the screen, which are caused by a defect in pixel of CCD image sensor.
Perform this adjustment after specified components have been replaced (see "List of Adjustment Items").
Perform this adjustment if spot noise occurs under abnormal usage conditions or after long-term use.
If spot noise still occurs after this adjustment is complete, the CCD image sensor may be defective.
Perform this adjustment after completing all other adjustments. (Perform this adjustment in normal video status.)
Main menu
***********************************************************
MANUAL ADJUSTMENT PROGRAM
***********************************************************
[A] DATA INITIALIZE
[B] ELECTRIC VOLUME
[C] ADJUSTMENT
[D] AUTO FOCUS
[E] SPOT NOISE
[ESC] END
Please select [A] - [F] or [ESC]
Input E.
Follow the instructions on PC display
thereafter.
9.1 Spot Noise Adjustment
Incompleted Phenomenon:
Spot noise occurs under abnormal usage conditions or after long-term use.
Equipment:
Color video monitor (CRT type is desirable)
Condition:
Cap the lens (so that no light enters).
Procedure:
1) Input Eto PC on the main menu screen.
2) Follow the instructions on PC display thereafter.
3) The screen for verifying writing of spot noise data will appear: Input Y. (*1)
4) When writing data is complete, the spot noise data write complete screen
will appear: Press any key to restore the main menu screen.
*1: Entering Non the screen for verifying writing of spot noise data will
restore the main menu screen.