Hitachi P50XR01E User manual

CAUTION:
Before servicing this chassis, it is important that the service technician read the “Safety
Precautions” and “Product Safety Notices” in this service manual.
ATTENTION:
Avant d’effectuer l’entretien du châassis, le technicien doit lire les «Précautions de sécurité»
et les «Notices de sécurité du produit» présentés dans le présent manuel.
VORSICHT:
Vor Öffnen des Gehäuses hat der Service-Ingenieur die „Sicherheitshinweise“ und „Hinweise
zur Produktsicherheit“ in diesem Wartungshandbuch zu lesen.
SERVICE MANUAL
MANUEL D'ENTRETIEN
WARTUNGSHANDBUCH
Data contained within this Service
manual is subject to alteration for
improvement.
Les données fournies dans le présent
manuel d’entretien peuvent faire l’objet
de modifications en vue de perfectionner
le produit.
Die in diesem Wartungshandbuch
enthaltenen Spezifikationen können sich
zwecks Verbesserungen ändern.
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
Plasma TV
November 2007
SM017
P50XR01E
P50XR01U
P60XR01E
P60XR01U
All manuals and user guides at all-guides.com
all-guides.com

1
P50XR01U/E P60XR01U/E
1. Features -----------------------------------------------2
2. Specifications-----------------------------------------7
3. Servicing-----------------------------------------------8
4. Component names----------------------------------9
5. Adjustment ------------------------------------------ 15
6. Troubleshooting------------------------------------ 26
7. Self-diagnosis function --------------------------- 43
8. Waveform diagrams------------------------------ 45
9. Block diagrams------------------------------------- 47
10.Connection diagrams----------------------------- 49
11.Wiring diagrams----------------------------------- 51
12.Disassembly diagrams--------------------------- 55
13.Replacement partslist ---------------------------- 59
Contents
CAUTION FOR SAFETY
Please read this page before repairing the monitor.
This page explains the following items for keeping the safety of set and preventing accidents
during repair.
Smols Used:
Warning This symbol means "possibility of death or heavy damage"
Caution This symbol means "possibility of damage or breakage"
This symbol means "CAUTION"
This symbol means "POSSIBILITY of
ELECTRIC SHOCK"
This symbol means "MUST"
This symbol means "DO NOT"
Follow instructions.
Special attention parts are indicated
on cabinter, chassis and parts by label.
Please follow the notesin [Safety In-
structions] in the User’s Manual.
Prevent electric shock.
Take care during working because
the monitor has high voltage parts
and power supply parts.
Possibility of electric shock if these
parts are touched.
Disconnect power plug during
overhaul, reassemble or parts change.
Daeth or injury by electric shock may
occur if live parts are touched.
Use recommended components.
Components and parts with special
characteristics for safety or reliability
are indicated in parts lists and circuit
diagrams by the mark.
Electric shock of fire may occur if non-
recommended components or parts
are used.
Keep the same style of wiring.
The Monitor uses insulating tubes
or tapes for safety and some comp-
nents are kept at a distance from
PCB surfaces for safety.
Internal leads kept from hot-or high
voltage partsby clampersor styling.
Return wiring to original condition after
repair to prevent electric shock or fire.
Perform safety check after finishing.
Every part (removed screws, compo-
nent and wiring) should be returned to
to its original condition.
Check around the repair position for
damage and measure insulation
impedance by using a meg-ohm me-
ter.
Confirm that the value of impedance
is more than 4M ohm.
Electric shock or fire may occur if
the value is less than 4M ohm.
The code and combination circuit of the
HDCP is not a repairable item.
Never remove the shield case that is
assembled to the code and combination
circuit of the HDCP.
WARNING
14.Schematic diagrams ------------------------------ 60
All manuals and user guides at all-guides.com

2
P50XR01U/E P60XR01U/E
PRECAUTIONS
Cleaning the plasma screen panel of the monitor
Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet.
To prevent scratching or damaging the plasma screen face, do not knock or rub the surface with sharp or
hard objects. Clean the screen with a soft cloth moistened with warm water and dry with a soft cloth. If it is
not enough, then use a cloth with mild detergent. Do not use harsh or abrasive cleaners.
Cleaning the cabinet of the monitor
Use a soft cloth to clean the cabinet and control panel of the monitor. When excessively soiled dilute a neu-
tral detergent in water, wet and wring out the soft cloth and afterward wipe with a dry soft cloth.
Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax,
glass cleaner, etc. especially because they would cause discolouration, scratches or cracks.
Information for users applicable in European Union countries
This symbol on the product or on its packaging means that your electrical and electronic
equipment should be disposed at the end of life separately from your household waste.
There are separate collection systems for recycling in EU. For more information, please con-
tact the local authority or the dealer where you purchased the product.
1. Features
Large-screen, high-definition plasma display panel
The 50-inch colour plasma display panel, with a resolution of 1920 (H) x 1080 (V) pixels, and the 60-inch colour plasma
display panel, with a resolution of 1920 (H) x 1080 (V) pixels, creates a high-definition, large-screen (aspect ratio:
16:9) and low-profile flat display. Free from electromagnetic interferences from geomagnetic sources and ambient
power lines, the panel produces high-quality display images free from colour misconvergence and display distortion.
High Performance Digital Processor
A wide range of input signals can be handed, including composite, component and HDMI. High Definition Digital
Processor creates the fine-textured image with dynamic contrast.
Easy-to-use remote control and on screen display system
The remote control included eases the work of setting display controls. Further, the on-screen display sys-
tem, displays the status of signal reception and display control settings in an easy-to-view fashion.
Connecting to an Audio Visual Device
• Three Scart terminals*1, composite/S terminal*2, a component terminal*3, and two HDMI terminals have been
added. A composite video output terminal is also provided as a monitoring output.
*1 AV1 scart applies to composite/ S-video
AV2 and 3 scart applies to composite/ RGB
*2 AV5 composite/S-Video=Front Input
*3 AV4 can be connected to the equipment with either component or composite Output.
SD card slot installed
Power Swivel Feature (only P50XR01U/E)
It allows turning the plasma display left or right within ±30 degree using the remote control.
All manuals and user guides at all-guides.com

3
P50XR01U/E P60XR01U/E
Digital Terrestrial Television Broadcasting
Converting into digital signalsenables more channels and various useful features, such as Electric
Programme Guide, Digital Teletext, and so on. Further, digital signal can create high quality picture.
This logo indicates that the product is compliant with European Digital Broadcasting.
DVB is a registered trademark of the DVB Project.
This logo indicates that the product is set up to view digital terrestrial TV.
FREEVIEW and the FREEVIEW logo are trade marks of DVT Services Ltd and are used under license.
FREEVIEW Logo © DTV Services Ltd 2002.
All manuals and user guides at all-guides.com

4
P50XR01U/E P60XR01U/E
PerformanceoftheFC8(FRC)Circuit
“FC8” is a term for Hitachi’s original LSI having FRC function. “FRC” stands for Frame Rate
Converter. By using Frame Rate Converter technology for moving compensation, this circuit
creates higher picture quality and has the following functions:
1) Telecine performance (as applying “Film mode”): Judder Reduction
2) Improvement on PDP moving image by FRC from 50Hz to 60Hz.
From the perspective of hardware, this function is actualised by newly mounting FC8 LSI and 3
sets of 256Mbit-DDR2 memories on the FC8 board (which is only for this function).
As a block component, the FC8 board is locatedin front of panel block. It inputs the picture signal
of the LVDS system (available: single/dual system) and then once processing the FRC as
mentioned above, it outputs the picture signal of LVDS system (available: single/dual system)
again in order to supply the panel. As the control of FC8 board, I/F of the original FC Bus system is
utilised.
2 power supplies are necessary: 5.6V and 3.2V. The other necessary power supplies are generated
on the FC8 board.
All of the above I/F are combined into 1x 160-pin BtoB connector.
FC8(FRC) Block
160pin㩷BtoB
Panel
䋨PDP䋩
䋨LCD䋩
Seine 2D
Main Board
FC8 Board
FC8
Reg.
5.6V
3.3V Nereid
Slow Bus
LVDS1
LVDS2
LVDS1
LVDS2
DDR2
All manuals and user guides at all-guides.com

5
P50XR01U/E P60XR01U/E
Handling the HDD (Hard Disk Drive)
HDD is a high precision device, and is very susceptible to vibrations or impact. Even if HDD
operates normally immediately after it has been subjected to vibrations or impact, a problem may
occur after it is used for a while: When servicing, take great care with the following.
There are two types of HDD: CSS format (head remains on disk regardless of operation status)
and ramp loading format (head moves away from disk during no operation). The impact resistance
characteristics are slightly different for the two. When servicing, observe the following cautions
regardless of the format:
(1) Cautions during unpacking
1) Do not subject the HDD to any impact when placing on desk: The head hitting against the desk
could result in damage.
2) If condensation occurs because of the environment, leave the HDD without being turned on for at
least 3 hours until it adapts to surrounding environment. If the HDD is turned on while the head
is sticking to disk because of condensation, the disk may be damaged.
(2) Cautions during transportation
An HDD is more susceptible to vibrations or impact when it is turned on or operating than during
no operation.
1) Do not move the HDD while it is turned on: If the HDD is subject to any impact while the disk is
rotating, i.e., the head hitting against the disk, breakage could result.
2) Move the HDD approximately 2 minutes (approximately 30 seconds for surveillance system
devices) after turning it off and unplugging its power cord from AC outlet. The disk will still be
rotating by inertia immediately after the HDD is turned off: Subjecting the HDD to movement at
this time could destroy it.
(3) Cautions during operation
1) Do not unplug the power cord from AC outlet during operation: This could damage the data on
HDD. Be sure to turn the HDD off before unplugging the power cord.
2) Do not hit the HDD: The head hitting the disk could result in breakage.
(4) Caution during packing
1) Use the packing material of relevant model: Material superior in impact resistance is used. Using
other packing materials could result in fault.
(5) Cautions when handling unassembled HDD
1) Hold the HDD at both sides so that the circuit board surface is facing below: Holding the HDD at
the top and bottom could cause the head to drift, which could result in fault.
2) Do not touch the terminal or pattern on circuit board.
3) Place HDD on a spot where cushion is pasted with the circuit board surface facing below.
4) Do not hold or place stacked HDDs.
5) Do not drop or hit HDD against anything: Dropping HDD from even 5 mm high on a work bench
with high stiffness could cause fault.
All manuals and user guides at all-guides.com
all-guides.com

6
P50XR01U/E P60XR01U/E
Performance of theX-code2U Circuit Part
X-code2U makes digital broadcasting compression efficiency and hasa function to realise recording for a long time (TS
recording); in addition it possesses the MPEG encoding function to cope with analog broadcasting recording.
Recording Mode and Recording Time
There are 5 recording modes (Fig.1). The quality of the recorded picture varies depending on Recording Mode.
Following is the block diagram (Fig.2) of the recording processes.
The digital broadcasting inputs it into X-code2U after it was input into Tenko Φ. X-code2U performs transformer code
processing in real time and returns it to Tenko Φagain and passes through the SATA conversion to HDD and is
recorded. X-code2U has a separate input port for analog recording. It is recorded in the same pass on the HDD
after MPEG encoding.
TenkoΦ
IU01
SATA
IU06
250GB
HDD
TS
Play
Digital
channel
TS
X-code2U
IX01
Audio LR
Picture
Analog input
(After ADC)
Fig.2 block diagram of the recording processing
MODE DTT TV Quality
TS
XP
SP
LP
EP
about 93 hours
-
-
-
-
-
about 50 hours
about 95 hours
about 190 hours
about 310 hours
High
Low
*In EP mode, display resolution is lower. Select more than LP mode if the finer picture is preferred.
Fig.1
All manuals and user guides at all-guides.com

7
P50XR01U/E P60XR01U/E
2. Specifications
Panel Display dimensions
P50XR01U/E P60XR01U/E
Approx. 50 inches
(1106(H) x 626(V) mm, diagonal 1270mm)
Approx. 60 inches
(1336(H) x 751(V) , diagonal 1530mm)
Resolution 1920(H) x 1080 (V) pixels 1920(H) x 1080 (V) pixels
Net dimensions
including Stand:
1250(W)x890(H)x423(D) mm
excluding Stand:
1250(W)x823(H)x129(D) mm
including Stand&Speaker:
1773(W)x1018(H)x483(D) mm
including Speaker, excluding Stand:
1773(W)x952(H)x128(D) mm
excluding Stand:
1502(W)x1018(H)x483(D) mm
Net weight including Stand: 51.3Kg
excluding Stand: 445.2Kg
including Stand&Speaker: 100Kg
excluding Stand&Speaker: 75Kg
Ambient
conditions
Temperature Operating : 5°C to 35°C, Storage : 0°C to 40°C
Relative humidity Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)
Power supply AC220 - 240V, 50Hz
Power consumption/ at standby 540W / <0.8W W / <0.8W
Audio output speaker total 32W speaker total 27W
(VIDEO input)
Input terminals
AV1 : composite video input terminal (SCART)
S video input terminal (SCART)
L/R audio input terminal (SCART)
AV2•3 : composite video input terminal (SCART)
RGB video input terminal (SCART)
L/R audio input terminal (SCART)
AV4 : composite video input terminal (RCA)
component video input terminal.(RCA)
L/R audio input terminal (RCA)
AV5 : composite video input terminal (RCA)
S video input terminal (Mini DIN)
L/R audio input terminal (RCA)
HDMI 1•2•3 : HDMI input terminal
Audio input terminal (3.5mm Stereo Mini Jack)*
Photo Input : Photo Input terminal / SD card slot
Input signals
Composite video: PAL, SECAM, NTSC3.58, NTSC4.43, PAL60
Component video: 480i, 576i, 480p, 576p, 720p/50, 720p/60, 1080i/50, 1080i/60
HDMI:VGA/60, 480i, 576i, 480p, 576p, 720p/50, 720p/60, 1080i/50, 1080i/60, 1080,
1080p/60, 1080p/24
Output Signal
OUTPUT (MONITOR): composite video monitor-output terminal (RCA)
OUTPUT (MONITOR): L/R audio monitor- output terminal (RCA)
OUTPUT (HEADPHONE): L/R audio monitor- output terminal (3.5mm Stereo Mini Jack)
OUTPUT (SUB-WOOFER): woofer output terminal (RCA)
AV1/2/3 : composite video output terminal (SCART)
L/R audio output terminal (SCART)
Optical Out: PCM/Dolby Digital
(RF input)
Input terminal / Receiving range ANT : 75Unbalanced / 40~870MHz
RF Video System
PAL B, G, H / I / D, K
SECAM B, G / K1 / L, L' / D,K
DVB-T
(RGB input)
Input terminals Analog RGB input terminal (D-sub 15pin)
Audio input terminal (3.5mm Stereo Mini Jack)*
Input signals 0.7Vp-p, analog RGB (Recommended Signal)
Sync singnals H/V separate, TTL level [2k]
• The unit takes at least 30 minutes to attain the status of optimal picture quality.
* This analog audio input terminal can be used for PC (RGB) or HDMI1~3 only.
All manuals and user guides at all-guides.com

8
P50XR01U/E P60XR01U/E
3. Servicing
Lead free solder
This product uses lead free solder (unleaded) to help preserve the environment. Please read these
instructions before attempting any soldering work.
Caution: Always wear safety glasses to prevent fumes or molten solder from getting into the eyes. Lead
free solder can splatter at high temperatures (600˚C).
Lead free solder indicator
Printed circuit boards using lead free solder are engraved with an "F."
Properties of lead free solder
The melting point of lead free solder is 40-50˚C higher than leaded solder.
Servicing solder
Solder with an alloy composition of Sn-3.0Ag-0.5Cu or Sn-0.7Cu is recommended.
Although servicing with leaded solder is possible, there are a few precautions that have to be taken. (Not
taking these precautions may cause the solder to not harden properly, and lead to consequent malfunctions.)
Precautions when using leaded solder
Remove all lead free solder from soldered joints when replacing components.
If leaded solder should be added to existing lead free joints, mix in the leaded solder thoroughly after the
lead free solder has been completely melted (do not apply the soldering iron without solder).
Servicing soldering iron
A soldering iron with a temperature setting capability (temperature control function) is recommended.
The melting point of lead free solder is higher than leaded solder. Use a soldering iron that maintains a high
stable temperature (large heat capacity), and that allows temperature adjustment according to the part being
serviced, to avoid poor servicing performance.
Recommended soldering iron:
Soldering iron with temperature control function (temperature range: 320-450˚C)
Recommended temperature range per part:
Part Soldering iron temperature
Mounting (chips) on mounted PCB 320˚C±30˚C
Mounting (chips) on empty PCB 380˚C±30˚C
Chassis, metallic shield, etc. 420˚C±30˚C
CONTROL PCB (Control PCB, Slot PCB, SD PCB, PC PCB)
TERMINAL PCB (Terminal PCB, LED PCB, Swivel PCB)
FILTER PCB
MAIN PCB
FC8 PCB
Board assemblies which use lead free solder
Readjustment Power supply voltage
When a PANEL or a Power Unit is exchanged, power supply voltage is automatically adjusted.
However, Please reconfirm to the values of Vs and Va, as shown on the label carrently stuck on the panel
back upper parts.
Please refer to the reconfirm the “Vs and Va” voltages on Power Unit.
All manuals and user guides at all-guides.com

9
P50XR01U/E P60XR01U/E
4. Component names
[Main unit]
Front Panel
Rear Panel
1 Cabinet
2 Panel
3 Remote Control Receiver
4 HDD/Timer Indicating Lamp
5 Power Indicating Lamp
6 Main Power Switch (On the bottom surface)
7 Control Panel and Front Input
8 Desktop Stand
9 Speaker (Option for 60” model)
1
2
6
50” model
3
4
8
7
1
2
6
60” model
3
4
8
7
9
9
55
1 Terminal board (External Device Connection)
2 Power Cord Socket
3 Handgrips
4 Terminals for speaker cables on television
5 Terminals for speaker cables on speaker
2
1
3
50” model
2
1
3
60” model
4
5
5
All manuals and user guides at all-guides.com

10
P50XR01U/E P60XR01U/E
Control Panel (including front input)
1 Front Input
2 Stop/Play button
3 Rec (Recording) button
4 Menu/Return button
5 Input Select/OK button
6 Volume Down/Żbutton
7 Volume Up/Źbutton
8 Channel Down/źbutton
9 Channel Up/Ÿbutton
10 Sub Power button
CAUTION * for 60” model
Do not place your ?ngers into the
gap at the opened door. If your
?ngers are caught in the front door,
you may be injured.
A Push the bottom centre of
the front door to unlock.
B Pull down the upside of the
door.
Push here to open the door.
B
A
123456789
10
A
Push here to open the door.
ledom”06ledom”05
50” model
60” model
A Push the bottom centre of
the front door to unlock.
B Lift it up from the
underside of the door.
B
All manuals and user guides at all-guides.com
all-guides.com

11
P50XR01U/E P60XR01U/E
[Remote control]
[for *** rof[]ledomE10RX ***XR01U model]
All manuals and user guides at all-guides.com

12
P50XR01U/E P60XR01U/E
1Sub Power
2Device Select (TV/DTT, DVD, SAT)
Press these buttons to select the device (TV/DTT,
DVD, or SAT) to be controlled by this remote
control. The selected button blinks once. Normally,
select “TV/DTT”.
3
Programme Select/Input Mode [Page Select]
Press these buttons to select a TV programme directly.
You can also use these buttons when changing the
Input mode.
4Freeze/Multi Mode [Hold]
5CHI/II
This is exclusively for TV audio A2/NICAM mode.
Also, press this button to select Audio Language in
DTT mode.
6Volume Up/Down
7Colour [Colour]
8TV/Text [TV Text]
This switches between the TV mode and the
Teletext mode.
9Time [Cancel]
Pressing this button can indicate the time by On-
screen display when receiving an analogue TV
programme on the screen.
10 Menu
Press this button to select Main Menu.
Cursor [Item Select]
OK
Function/Video Plus+ (***XR01U model)/
SHOWVIEW (***XR01E model)*
Press this button to select Function Menu.
Pause/TIME SHIFT*
Play*
Rewind and Forward*
Rec*
TITLE LIST*
Recall
Press this button to show the input signal status.
Picture Mode
Picture mode can be changed each time pressed in the
following sequence. DynamicĺNaturalĺCinema
Swivel (with Desktop Stand)
This function is to rotate TV. Select the degree of
rotation with cursor key.
This is not available for 60” model.
Input Select
You can use this to change the input mode.
Multi Picture
Press this button to change the picture to multi-
picture mode. Press it again to return to normal
picture.
Channel Up/Down
Mute
[Reveal]
DVB Subtitle Language
Guide [Index]
Return
You can use this to return to the previous menu.
Stop*
Skip*
Photo Input/ 30-Second Skip*
Press this button to display and control the pictures
from digital still camera, USB card reader, or SD
(MMC) card.
REC MODE/10-Second Back*
11
12
13
14
15
16
17
18
19
21
20
22
23
24
25
26
27
28
29
30
31
32
33
All manuals and user guides at all-guides.com

13
P50XR01U/E P60XR01U/E
[Terminal Positions]
1
1
Rear
1
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
17
18
18
19
19
20
20
21
21
22
Power Cord Socket
2 Aerial Socket
3AV1
4AV2
5AV3
6AV4
7 Monitor Out
8 Service use only
9 Service use only
Power Swivel Terminal
* Not available for 60” model.
Optical Out (Digital Audio)
HDMI 2
HDMI 3
Common interface slot
PC Terminals
Mini stereo for Audio
Sub woofer
Front
AV5
Headphone terminal
HDMI 1
SD Memory Card slot
Photo Input terminal
SUB
WOOFER
Rear
1 Power Cord Socket
2 Aerial Socket
3AV1
4AV2
5AV3
6AV4
7 Monitor Out
8 Service use only
9 Service use only
Optical Out (Digital Audio)
HDMI 2
HDMI 3
Common interface slot
PC Terminals
Mini stereo for Audio
Sub woofer
Front
AV5
Headphone terminal
HDMI 1
Photo Input terminal
SD Memory Card slot
SUB
WOOFER
[50” model]
[60” model]
6
7
3
21 20 19 18 17
45
6
16
10
2
8
13
14 15 9
11
12
21 19 18
17
22 20
7
2
8
12
13
14
9
15 16
All manuals and user guides at all-guides.com

14
P50XR01U/E P60XR01U/E
[60V SPEAKER SYSTEMS SPECIFICATION]
Model ............................ SP01G60E
Type ............................ 2 way 3 speakers, Bass Reflex
Woofer............................ 100mm cone type ×2 each
Tweeter ........................ 25mm dome type
Impedance .................... 6ȍ
Max.input power ............ 50W
RMS input power............ 20W
External Dimensions .... 132.5(W) × 951.6(H) × 117.2(D) mm each
Weight ............................ 2.3Kg each
Specifications and design subject to possible
modification without notice,due to improvements.
132.5 117.2
951.6
Specifications
All manuals and user guides at all-guides.com

15
P50XR01U/E P60XR01U/E
5. Adjustment
䊶How to get to Adjustment mod
e
Using the remote controller with the set turned on can activate it
.
Press the Programme Select button "1","GREEN"and "YELLOW" colour button at the same time, and hold for more than 3 seconds
The set is displayed adjustment mode.
I show the operation method of each item as follows
.
normal screen
1st Page
ADJUST MODE (***-**V-EU)ZZZZ
FACT RESET
MEMORY INI
T
RGB
WHITE BAL Cool
WHITE BAL Normal
WHITE BAL Warm
WHITE BAL B/W
2nd Page
ADJUST MODE (***-**V-EU)ZZZZ
MAINTENANCE
DEVICE
M306H5 V01.00
A
DJ.REV. V01.01
PANEL_TIME
䊶Various adjustmen
t
FACT RESET It returns setting at the time of shipment
.
ADJUST MODE (***-**V-EU)ZZZZ
FACT RESET
MEMORY INI
T
RGB
WHITE BAL Cool
WHITE BAL Normal
WHITE BAL Warm
WHITE BAL B/W
MEMORY INIT When there were instructions, please carry it out
.
ADJUST MODE (***-**V-EU)ZZZZ
FACT RESET
MEMORY INI
T
RGB
WHITE BAL Cool
WHITE BAL Normal
WHITE BAL Warm
WHITE BAL B/W
SELF TEST
65535
㪧㫉㫆㪾㫉㪸㫄㪼㪼㩷㪪㪼㫃㪼㪺㫋
㪹㫌㫋㫋㫆㫅
㩹㪈㩹
㩹㪞㪩㪜㪜㪥㩹
㪺㫆㫃㫆㫉㩷㪹㫌㫋㫋㫆㫅
㩹㪰㪜㪣㪣㪦㪮㩹
㪺㫆㫃㫆㫉㩷㪹㫌㫋㫋㫆㫅
㪩㪼㫋㫌㫉㫅
㪂
㪂
㪧㫌㫊㪿㫀㫅
㪾
㩷㪸㫋㩷㫋㪿㪼㩷㫊㪸㫄㪼㩷㫋㫀㫄㪼
㪩㪼㫋㫌㫉㫅
䂥䂯
㫉㫌㫅㫅㫀㫅㪾
䊶㪪㪼㫀㫅㪼
䊶㪛㫉㫀㫍㪼㩷㪬㫇
㪥㫆㫉㫄㪸㫃㩷㫋㪼㫉㫄㫀㫅㪸㫋㫀㫆㫅
㶎㪩㪼㪻㩷㫀㫊㩷㪻㫀㫊㫇㫃㪸㫐㪼㪻
㫎㪿㪼㫅㩷㪸㪹㫅㫆㫉㫄㪸㫃㩷㪼㫅㪻㫀㫅㪾㪅
㪚㫆㫅㫋㫀㫅㫅㪼㫊㩷㫇㫌㫊㪿㫀㫅㪾㩷㪽㫆㫉㩷㪉㩷㫊㪼㪺㫆㫅㪻㫊
㪤㪸㪾㪼㫅㫋㪸 㪞㫉㪼㪼㫅
㪩㪼㪻
㫉㫌㫅㫅㫀㫅㪾
䊶㪪㪼㫀㫅㪼
䊶㪛㫉㫀㫍㪼㩷㪬㫇
㪥㫆㫉㫄㪸㫃㩷㫋㪼㫉㫄㫀㫅㪸㫋㫀㫆㫅
㶎㪩㪼㪻㩷㫀㫊㩷㪻㫀㫊㫇㫃㪸㫐㪼㪻
㫎㪿㪼㫅㩷㪸㪹㫅㫆㫉㫄㪸㫃㩷㪼㫅㪻㫀㫅㪾㪅
㪚㫆㫅㫋㫀㫅㫅㪼㫊㩷㫇㫌㫊㪿㫀㫅㪾㩷㪽㫆㫉㩷㪉㩷㫊㪼㪺㫆㫅㪻㫊
㪹㫃㫌㪼 㪞㫉㪼㪼㫅
㪩㪼㪻
㪫㪿㫀㫊㩷㫀㫋㪼㫄㩷㫀㫊㩷㪸㪻㫁㫌㫊㫋㩷㫉㪼㫍㫀㪼㫎㩷㫅㫌㫄㪹㪼㫉㪅
㪫㪿㫀㫊㩷㫀㫋㪼㫄㩷㫀㫊㩷㫊㫌㪹㩷㫫㪺㫆㫄㩾㫊㩷㫍㪼㫉㫊㫀㫆㫅㩷㫅㫌㫄㪹㪼㫉㪅
㪫㪿㫀㫊㩷㫀㫋㪼㫄㩷㫀㫊㩷㫇㪸㫅㪼㫃㩷㫋㫀㫄㪼㩿㪿㫆㫌㫉㪀㪅
㪫㪿㫀㫊㩷㫀㫋㪼㫄㩷㫀㫊㩷㪻㫀㫊㫇㫃㪸㫐㪼㪻㩷㪸㫊㩷㪽㫆㫃㫃㫆㫎㫊㪅
㪧㪌㪇㪯㪩㪇㪈㪬㩷㪑㩷㪧㪛㪧㪄㪌㪇㪭㪄㪜㪬㪲㪏㪽㪈㪇㪴
㪧㪌㪇㪯㪩㪇㪈㪜㩷㪑㩷㪧㪛㪧㪄㪌㪇㪭㪄㪜㪬㪲㪐㪽㪈㪇㪴
㪧㪍㪇㪯㪩㪇㪈㪬㩷㪑㩷㪧㪛㪧㪄㪍㪇㪭㪄㪜㪬㪲㪏㪽㪈㪋㪴
㪧㪍㪇㪯㪩㪇㪈㪜㩷㪑㩷㪧㪛㪧㪄㪍㪇㪭㪄㪜㪬㪲㪐㪽㪈㪋㪴
㪝㪘㪚㪫㪦㪩㪰㩷㪩㪜㪪㪜㪫
䋨䋱䋩㪪㪼㫃㪼㪺㫋㩷㪲㪝㪘㪚㪫㩷㪩㪜㪪㪜㪫㪴㩷㫆㪽㩷㫋㪿㪼㩷㫊㪼㫉㫍㫀㪺㪼㩷㪸㪻㫁㫌㫊㫋㫄㪼㫅㫋㩷㫄㪼㫅㫌㩷㪹㫐
㪲㩷䂯㩷㪴㩷㫂㪼㫐㩷㫆㪽㩷㫉㪼㫄㫆㫋㪼㩷㪺㫆㫅㫋㫉㫆㫃㪅
䋨䋲䋩㪧㫉㪼㫊㫊㩷㪲㩷 㩷㪴㩷㫂㪼㫐㩷㫆㪽㩷㫉㪼㫄㫆㫋㪼㩷㪺㫆㫅㫋㫉㫆㫃㪃㩷㫋㪿㪼㫅㩷㪝㪸㪺㫋㫆㫉㫐㩷㪪㪿㫀㫇㫇㫀㫅㪾
㪪㪼㫋㫋㫀㫅㪾㫊㩷㪹㪼㪾㫀㫅㪅
䋨䋳䋩㪤㪸㪾㪼㫅㫋㪸㩷㫀㫊㩷㪻㫀㫊㫇㫃㪸㫐㪼㪻㩷㫎㪿㫀㫃㪼㩷㪝㪸㪺㫋㫆㫉㫐㩷㪪㪿㫀㫇㫇㫀㫅㪾㩷㪪㪼㫋㫋㫀㫅㪾㫊
㫆㫇㪼㫉㪸㫋㫀㫆㫅㪅
䇭㩷㩷㩷㪞㫉㪼㪼㫅㩷㫀㫊㩷㪻㫀㫊㫇㫃㪸㫐㪼㪻㩷㫎㪿㪼㫅㩷㫅㫆㫉㫄㪸㫃㩷㪼㫅㪻㫀㫅㪾㪅
㩷㩷㩷㩷㩷㪩㪼㪻㩷㫀㫊㩷㪻㫀㫊㫇㫃㪸㫐㪼㪻㩷㫎㪿㪼㫅㩷㪸㪹㫅㫆㫉㫄㪸㫃㩷㪼㫅㪻㫀㫅㪾㪅
䋨㪋䋩㪘㫋㩷㫋㪿㪼㩷㫋㫀㫄㪼㩷㫆㪽㩷㫋㪿㪼㩷㫅㫆㫉㫄㪸㫃㩷㪼㫅㪻㪃㩷㫇㫃㪼㪸㫊㪼㩷㪻㫆㩷㪦㪝㪝㪆㪦㪥㩷㫆㪽㩷㫋㪿㪼
㫄㪸㫀㫅㩷㫇㫆㫎㪼㫉㩷㫊㫌㫇㫇㫃㫐㪅
㪤㪜㪤㪦㪩㪰㩷㪠㪥㪠㪫㪠㪘㪣㪠㪱㪜
䋨䋱䋩㪪㪼㫃㪼㪺㫋㩷㪲㪤㪜㪤㪦㪩㪰㩷㪠㪥㪠㪫㪴㪅
䋨䋲䋩㪤㪜㪤㪦㪩㪰㩷㪠㪥㪠㪫㪠㪘㪣㩷㫊㫋㪸㫉㫋㫊㩷㪹㫐㩷㪺㫆㫅㫋㫀㫅㫌㫀㫅㪾㩷㫇㫌㫊㪿㫀㫅㪾㩷㪲㩷 㩷㪴㩷㪹㫌㫋㫋㫆㫅
㪽㫆㫉㩷㫋㫎㫆㩷㫊㪼㪺㫆㫅㪻㫊㪅
䋨䋳䋩㪫㪿㪼㩷㫊㪺㫉㪼㪼㫅㩷㪺㪿㪸㫅㪾㪼㫊㩷㫀㫅㫋㫆㩷㪹㫃㫌㪼㩷㫎㪿㪼㫅㩷㪤㪜㪤㪦㪩㪰㩷㪠㪥㪠㪫㩷㫊㫋㪸㫉㫋㪅
䇭㩷㩷㩷㪫㪿㪼㩷㫊㪺㫉㪼㪼㫅㩷㪺㪿㪸㫅㪾㪼㫊㩷㫀㫅㫋㫆㩷㪾㫉㪼㪼㫅㩷㫎㪿㪼㫅㩷㪤㪜㪤㪦㪩㪰㩷㪠㪥㪠㪫㩷㪽㫀㫅㫀㫊㪿
㫅㫆㫉㫄㪸㫃㫃㫐㪅
㩷㩷㩷㩷㩷㪫㪿㪼㩷㫊㪺㫉㪼㪼㫅㩷㪺㪿㪸㫅㪾㪼㫊㩷㫀㫅㫋㫆㩷㫉㪼㪻㩷㫎㪿㪼㫅㩷㪤㪜㪤㪦㪩㪰㩷㪠㪥㪠㪫㩷㪽㫀㫅㫀㫊㪿
㪸㪹㫅㫆㫉㫄㪸㫃㫃㫐
䋨㪋䋩㪘㫋㩷㫋㪿㪼㩷㫋㫀㫄㪼㩷㫆㪽㩷㫋㪿㪼㩷㫅㫆㫉㫄㪸㫃㩷㪼㫅㪻㪃㩷㫇㫃㪼㪸㫊㪼㩷㪻㫆㩷㪦㪝㪝㪆㪦㪥㩷㫆㪽㩷㫋㪿㪼
㫄㪸㫀㫅㩷㫇㫆㫎㪼㫉㩷㫊㫌㫇㫇㫃㫐㪅
㪥㪦㪫㪜㪑㪫㪿㪼㩷㪼㫏㪼㪺㫌㫋㫀㫆㫅㩷㫆㪽㩷㫋㪿㫀㫊㩷㪽㫌㫅㪺㫋㫀㫆㫅㩷㫉㪼㫋㫌㫉㫅㫊㩷㫋㪿㪼㩷㪸㪻㫁㫌㫊㫋㫄㪼㫅㫋
㪺㫆㪻㪼㫊㩷㫋㫆㩷㫋㪿㪼㩷㫇㫉㪼㫊㪼㫋㩷㫍㪸㫃㫌㪼㫊㪃㩷㫋㪿㪼㫉㪼㪽㫆㫉㪼㪃㩷㪸㪻㫁㫌㫊㫋㫄㪼㫅㫋㩷㪻㪸㫋㪸㩷㫎㫀㫃㫃㩷㪹㪼
㫃㫆㫊㫋㪅
㩷㩷㩷㪮㪿㪼㫅㩷㫐㫆㫌㩷㫇㪼㫉㪽㫆㫉㫄㩷㪤㪜㪤㪦㪩㪰㩷㪠㪥㪠㪫㪠㪘㪣㪠㪱㪜㪃㩷㫋㪿㪼㩷㪽㫆㫃㫃㫆㫎㫀㫅㪾㩷㫀㫋㪼㫄㫊
㪸㫉㪼㩷㫅㫆㫋㩷㫀㫅㫀㫋㫀㪸㫃㫀㫑㪼㪻㪅
㩷㩷㩷䊶㪮㪟㪠㪫㪜㩷㪙㪣㪘㪥㪚㪜㩷㪘㪛㪡㪬㪪㪫㪤㪜㪥㪫㩷㪛㪘㪫㪘
㩷㩷㩷䊶㪪㪬㪙㩷㪚㪦㪥㪫㪩㪘㪪㪫㩷㪘㪛㪡㪬㪪㪫㪤㪜㪥㪫㩷㪛㪘㪫㪘
㩷㩷㩷䊶㪚㪣㪘㪥㪧㩷㪦㪝㪝㪪㪜㪫㩷㪘㪛㪡㪬㪪㪫㪤㪜㪥㪫㩷㪛㪘㪫㪘
㩷㩷㩷㪙㫌㫋㩷㫋㪿㪼㩷㪽㫆㫃㫃㫆㫎㫀㫅㪾㩷㫀㫋㪼㫄㫊㩷㪸㫉㪼㩷㫀㫅㫀㫋㫀㪸㫃㫀㫑㪼㪻㪅
㩷㩷㩷䊶㪦㪫㪟㪜㪩㩷㪘㪛㪡㪬㪪㪫㪤㪜㪥㪫㩷㪛㪘㪫㪘
㩷㩷㩷䊶㪝㪘㪚㪫㪦㪩㪰㩷㪩㪜㪪㪜㪫㩷㪠㪫㪜㪤
All manuals and user guides at all-guides.com
all-guides.com

16
P50XR01U/E P60XR01U/E
RGB
ADJUST MODE (***-**V-EU)ZZZZ
FACT RESET
MEMORY INI
T
RGB
WHITE BAL Cool
(
RGB_Amp ADJUSTING
)
WHITE BAL Normal
WHITE BAL Warm
WHITE BAL B/W
WHITE BAL Cool,Normal,Warm,B/W(Black&White
)
Please refer to page 24&25 in detail
.
A
DJUST MODE (***-**V-EU)ZZZZ ADJUST MODE (***-**V-EU)ZZZZ
FACT RESET R DRV Cool **
MEMORY INI
T
G DRV Cool **
looCVRDBBGR **
WHITE BAL Cool
WHITE BAL Normal
WHITE BAL Warm
WHITE BAL B/W ADJUST MODE (***-**V-EU)ZZZZ
R DRV C
oo
l
**
G DRV Cool **
B DRV Cool **
ADJUST MODE (***-**V-EU)ZZZZ
R DRV Cool **
G DRV Cool **
B DRV Cool **
SELF TEST Please refer to page 44 in detail
.
ADJUST MODE (***-**V-EU)ZZZZ
MAINTENANCE
DEVICE
M306H5 V01.00
A
DJ.REV. V01.01
PANEL_TIME SELF_TEST䇭screen
MAINTENANCE Please refer to page 18 in detail
.
ADJUST MODE (***-**V-EU)ZZZZ
MAINTENANC
E
DEVICE
neercsECNANETNIAM00.10V5H603M
A
DJ.REV. V01.01
PANEL_TIME
SELF TEST
65535
65535
SELF TEST
㩷
㪚㫆㫅㫋㫀㫅㫅㪼㫊㩷㫇㫌㫊㪿㫀㫅㪾㩷㪽㫆㫉㩷㪉㩷㫊㪼㪺㫆㫅㪻㫊
㪘㪽㫋㪼㫉㩷㪺㫆㫄㫇㫃㪼㫋㫀㫅㪾㩷㫋㪿㪼㩷㪸㪻㫁㫌㫊㫋㫄㪼㫅㫋
㪛㪘㪫㪘
㪺㪿㪸㫅㪾㪼
㪛㪘㪫㪘
㪺㪿㪸㫅㪾㪼
䂥䂯
㪛㪘㪫㪘
㪺㪿㪸㫅㪾㪼
䂥䂯
㪩㪼㫋㫌㫉㫅
㪦㪢
㩷㫆㫉㩷
㪦㪢
㩷㫆㫉㩷
㪦㪢
㩷㫆㫉㩷
㪩㪞㪙㩷㪘㪛㪡㪬㪪㪫
㪧㫃㪼㪸㫊㪼㩷㫉㪼㪽㪼㫉㩷㫋㫆㩷㫇㪸㪾㪼㪉㪉㩷㫀㫅㩷㪻㪼㫋㪸㫀㫃㪅
䋨䋱䋩㪪㪼㫃㪼㪺㫋㩷㪲㪩㪞㪙㪴㪅
䋨䋲䋩㪧㫉㪼㫊㫊㩷㪲㩷 㩷㪴㩷㪽㫆㫉㩷㫆㫍㪼㫉㩷㪉㩷㫊㪼㪺㫆㫅㪻㫊㩷㫋㪿㪼㫅㩷㪩㪞㪙㩷㪘㫄㫇㫃㫀㫋㫌㪻㪼
㪘㪻㫁㫌㫊㫋㫄㪼㫅㫋㩷㫊㫋㪸㫉㫋㫊㩷㪸㫌㫋㫆㫄㪸㫋㫀㪺㪸㫃㫃㫐㪅
䋨䋳䋩㪦㪪㪛㩷㪻㫀㫊㪸㫇㫇㪼㪸㫉㫊㩷㫎㪿㫀㫃㪼㩷㫋㪿㪼㩷㪸㪻㫁㫌㫊㫋㫄㪼㫅㫋㩷㫀㫊㩷㫆㫇㪼㫉㪸㫋㫀㫅㪾㪅
㩷㩷㩷㩷㩷㪦㪪㪛㩷㪸㫇㫇㪼㪸㫉㫊㩷㪸㪾㪸㫀㫅㩷㫎㪿㪼㫅㩷㫋㪿㪼㩷㪸㪻㫁㫌㫊㫋㫄㪼㫅㫋㩷㫀㫊㩷㪺㫆㫄㫇㫃㪼㫋㪼㪻㪅
㪫㪿㪼㩷㫊㪺㫉㪼㪼㫅㩷㪹㪼㪺㫆㫄㪼㫊
㩹㪞㫉㪼㪼㫅㩹㩷㪽㫆㫉㩷㫆㫅㪼
㫊㪼㪺㫆㫅㪻㪅
䋨㪮㪿㪼㫅㩷㪸㪹㫅㫆㫉㫄㪸㫃
㪼㫅㪻㫀㫅㪾㪃㩷㫋㪿㪼㩷㫊㪺㫉㪼㪼㫅
㪹㪼㪺㫆㫄㪼㫊㩷㩹㪩㪼㪻㩹㩷㪽㫆㫉
㫆㫅㪼㩷㫊㪼㪺㫆㫅㪻㪅㩷䋩
㪮㪟㪠㪫㪜㩷㪙㪘㪣㩷㪚㫆㫆㫃㪃㪥㫆㫉㫄㪸㫃㪃㪮㪸㫉㫄㪃㪙㪆㪮㩿㪙㫃㪸㪺㫂㩽㪮㪿㫀㫋㪼㪀
㪧㫃㪼㪸㫊㪼㩷㫉㪼㪽㪼㫉㩷㫋㫆㩷㫇㪸㪾㪼㪉㪋㩽㪉㪌㩷㫀㫅㩷㪻㪼㫋㪸㫀㫃㪅
䋨䋱䋩㪪㪼㫃㪼㪺㫋㩷㪲㪮㪟㪠㪫㪜㩷㪙㪘㪣㩷㪚㫆㫆㫃䌾㪙㪆㪮㩿㪙㫃㪸㪺㫂㩽㪮㪿㫀㫋㪼㪀㪴㪅
䋨䋲䋩㪠㫋㩷㪸㪻㫁㫌㫊㫋㫊㩷㫀㫋㩷㫎㫀㫋㪿㩷㫋㪿㪼㩷㪲 㪴㩷㪹㫌㫋㫋㫆㫅㪅
䋨䋳䋩㪮㪿㪼㫅㩷㫋㪿㪼㩷㫍㪸㫃㫌㪼㩷㫀㫊㩷㪺㪿㪸㫅㪾㪼㪻㪃㩷㪸㩷㫊㪼㫋㩷㫍㪸㫃㫌㪼㩷㫀㫊㩷㫄㪸㪻㪼㩷㪸㩷㪾㫉㪼㪼㫅㩷㪺㪿㪸㫉㪸㪺㫋㪼㫉㪅
㩷㩷㩷㩷㩷㩷㪠㫋㩷㫉㪼㫋㫌㫉㫅㫊㩷㫀㫋㩷㫋㫆㩷㪸㩷㫎㪿㫀㫋㪼㩷㪺㪿㪸㫉㪸㪺㫋㪼㫉㩷㪹㫐㩷㫋㪿㪼㩷㫄㪼㫄㫆㫉㫐㩷㫇㫉㪼㫊㪼㫉㫍㪸㫋㫀㫆㫅㪅
㪪㪜㪣㪝㩷㪫㪜㪪㪫
㪧㫃㪼㪸㫊㪼㩷㫉㪼㪽㪼㫉㩷㫋㫆㩷㫇㪸㪾㪼㪋㪋㩷㫀㫅㩷㪻㪼㫋㪸㫀㫃㪅
䋨䋱䋩㪪㪼㫃㪼㪺㫋㩷㪲㪪㪜㪣㪝㩷㪫㪜㪪㪫㪴㪅
䋨䋲䋩㪠㫋㩷㪼㫅㫋㪼㫉㫊㩷㫋㪿㪼㩷㫊㪼㫃㪽㩷㫋㪼㫊㫋㩷㫊㪺㫉㪼㪼㫅㩷㫎㫀㫋㪿㩷㪲㩷 㩷㪴㩷㫆㫉㩷㫋㪿㪼㩷㪦㪢㩷㪹㫌㫋㫋㫆㫅㪅
㪤㪘㪠㪥㪫㪜㪥㪘㪥㪚㪜
䋨䋱䋩㪪㪼㫃㪼㪺㫋㩷㪲㪤㪘㪠㪥㪫㪜㪥㪘㪥㪚㪜㪴㪅
䋨䋲䋩㪠㫋㩷㪼㫅㫋㪼㫉㫊㩷㫋㪿㪼㩷㪤㪘㪠㪥㪫㪜㪥㪘㪥㪚㪜㩷㫊㪺㫉㪼㪼㫅㩷㫎㫀㫋㪿㩷㪲 㪴㩷㫆㫉㩷㫋㪿㪼㩷㪦㪢㩷㪹㫌㫋㫋㫆㫅㪅
All manuals and user guides at all-guides.com

17
P50XR01U/E P60XR01U/E
DEVICE Engineer uses onl
y
ADJUST MODE (***-**V-EU)ZZZZ ADJUST MODE (***-**V-EU)ZZZZ ADJUST MODE (***-**V-EU)ZZZZ ADJUST MODE (***-**V-EU)ZZZZ
DEVICE ITEM DAT
A
DEVICE ITEM DAT
A
DEVICE ITEM DAT
A
DEVICE ITEM DAT
A
FFF3##1FFF3##1FFF3##1FFF3##1
E1223E1223E1223E1223
F##51F##51F##51F##51
FF139FF139FF139FF139
C272C272C272C
272
803803803803
D5301D5301D5301D5301
11__ 11 __ 11 50
ADJUST MODE (***-**V-EU)ZZZZ
DEVICE ITEM DAT
A
1 ## 3FFF
322 1E
15 ## F
931 FF
27 2C
30 8
10 3 5D
11 50 FF
㪈㪃㪈 㪌㪃㪇
㪦㪢
㩷㫆㫉㩷
㪛㪘㪫㪘
㪺㪿㪸㫅㪾㪼
㪦㪢
㩷㫆㫉㩷
㪛㪜㪭㪠㪚㪜
䋨䋱䋩㪪㪼㫃㪼㪺㫋㩷㪲㪛㪜㪭㪠㪚㪜㪴㪅
䋨䋲䋩㪠㫋㩷㪼㫅㫋㪼㫉㫊㩷㫋㪿㪼㩷㪸㪻㫁㫌㫊㫋㫄㪼㫅㫋㩷㫊㪺㫉㪼㪼㫅㩷㫎㫀㫋㪿㩷㪲㩷 㩷㪴㩷㫆㫉㩷㫋㪿㪼㩷㪦㪢㩷㪹㫌㫋㫋㫆㫅㪅
䋨䋳䋩㪛㪜㪭㪠㪚㪜
㩷㽲㪫㪿㪼㩷㪺㫆㫅㫋㫉㫆㫃㩷㪻㪼㫍㫀㪺㪼㩷㫀㫊㩷㫊㪼㫃㪼㪺㫋㪼㪻㩷㫎㫀㫋㪿㩷㫋㪼㫅㩷㫂㪼㫐㫊㩷㪽㫉㫆㫄㩷㩹㪇㩹㩷㫋㫆㩷㩹㪐㪐㩹㪅
㩷㽳㪛㪜㪭㪠㪚㪜㩷㫀㫊㩷㪽㫀㫏㪼㪻㩷㫎㫀㫋㪿㩷㪲㩷 㩷㪴㩷㫆㫉㩷㫋㪿㪼㩷㪦㪢㩷㪹㫌㫋㫋㫆㫅㩷㪸㫅㪻㩷㫀㫋㩷㪺㪿㪸㫅㪾㪼㫊㩷㫋㫆㩷㪠㪫㪜㪤㪅
㩷㽴㪠㫋㩷㫉㪼㫋㫌㫉㫅㫊㩷㫋㫆㩷㪉㫅㪻㩷㫇㪸㪾㪼㩷㩹㪛㪜㪭㪠㪚㪜㩹㩷㪺㫃㪼㪸㫉㫀㫅㪾㩷㪸㫃㫃㩷㫀㫅㫇㫌㫋㩷㫎㪿㪼㫅㩷㪲㩷 㩷㪴㩷㫆㫉㩷㫋㪿㪼㩷㪩㪼㫋㫌㫉㫅㩷㪹㫌㫋㫋㫆㫅㩷㫀㫊㩷㫇㫌㫊㪿㪼㪻㪅
䋨䋴䋩㪠㪫㪜㪤
㩷㽲㪫㪿㪼㩷㪸㪻㫁㫌㫊㫋㫄㪼㫅㫋㩷㫀㫋㪼㫄㩷㫀㫊㩷㫊㪼㫃㪼㪺㫋㪼㪻㩷㫎㫀㫋㪿㩷㫋㪼㫅㩷㫂㪼㫐㫊㩷㪽㫉㫆㫄㩷㩹㪇㩹㩷㫋㫆㩷㩹㪐㪐㪐㩹㪅
㩷㽳㪠㪫㪜㪤㩷㫀㫊㩷㪽㫀㫏㪼㪻㩷㫎㫀㫋㪿㩷㪲㩷 㩷㪴㩷㫆㫉㩷㫋㪿㪼㩷㪦㪢㩷㪹㫌㫋㫋㫆㫅㪃㩷㪸㫅㪻㩷㫋㪿㪼㩷㫃㪸㫊㫋㩷㪸㪻㫁㫌㫊㫋㫄㪼㫅㫋㩷㫍㪸㫃㫌㪼㩷㫀㫊㩷㪻㫀㫊㫇㫃㪸㫐㪼㪻㩷㪸㫋㩷㫋㪿㪼㩷㪮㫉㫀㫋㪼
㫄㫆㪻㪼㪃㩷㪸㫅㪻㩷㫋㪿㪼㩷㫉㪼㪸㪻㫀㫅㪾㩷㪻㪸㫋㪸㩷㫀㫊㩷㪻㫀㫊㫇㫃㪸㫐㪼㪻㩷㪸㫅㪻㩷㫀㫋㩷㪺㪿㪸㫅㪾㪼㫊㩷㫋㫆㩷㪛㪘㪫㪘㩷㪸㫋㩷㫋㪿㪼㩷㪩㪼㪸㪻㩷㫄㫆㪻㪼㪅
㩷㽴㪠㫋㩷㫉㪼㫋㫌㫉㫅㫊㩷㫋㫆㩷㩹㪛㪜㪭㪠㪚㪜㩹㩷㫆㫅㩷㫋㪿㫀㫊㩷㫊㪺㫉㪼㪼㫅㩷㪺㫃㪼㪸㫉㫀㫅㪾㩷㫋㪿㪼㩷㫀㫅㫇㫌㫋㩷㫎㪿㪼㫅㩷㪲㩷 㩷㪴㩷㫆㫉㩷㫋㪿㪼㩷㫉㪼㫋㫌㫉㫅㫀㫅㪾㩷㪹㫌㫋㫋㫆㫅㩷㫀㫊
㫇㫌㫊㪿㪼㪻㪅
䋨䋵䋩㪛㪘㪫㪘
㩷㽲㪫㪿㪼㩷㪮㫉㫀㫋㪼㩷㫄㫆㪻㪼㩷㫀㫊㩷㪲 㪴㩷㫂㪼㫐㩷㪸㫅㪻㩷㪺㪿㪸㫅㪾㪼㪸㪹㫃㪼㩷㪸㫊㩷㪽㫆㫉㩷㫋㪿㪼㩷㪸㪻㫁㫌㫊㫋㫄㪼㫅㫋㩷㫍㪸㫃㫌㪼㪅㩷㪮㪿㪼㫅㩷㫋㪿㪼㩷㪦㪢㩷㪹㫌㫋㫋㫆㫅㩷㫀㫊
㫇㫌㫊㪿㪼㪻㪃㩷㫋㪿㪼㩷㪸㪻㫁㫌㫊㫋㫄㪼㫅㫋㩷㫍㪸㫃㫌㪼㩷㫄㪼㫄㫆㫉㫐㩷㫋㫆㩷㪝㪣㪘㪪㪟㪅
㩷㽳㪫㪿㪼㩷㪩㪼㪸㪻㩷㫄㫆㪻㪼㩷㫌㫇㪻㪸㫋㪼㫊㩷㫋㪿㪼㩷㪻㪼㫋㪼㪺㫋㫀㫆㫅㩷㫍㪸㫃㫌㪼㩷㫎㫀㫋㪿㩷㫋㪿㪼㩷㪲 㪴㩷㪸㫅㪻㩷㪦㪢㩷㫂㪼㫐㪅
㩷㽴㪠㫋㩷㫉㪼㫋㫌㫉㫅㫊㩷㫋㫆㩷㩹㪠㪫㪜㪤㩹㩷㫆㫅㩷㫋㪿㫀㫊㩷㫊㪺㫉㪼㪼㫅㩷㪺㫃㪼㪸㫉㫀㫅㪾㩷㫋㪿㪼㩷㫀㫅㫇㫌㫋㩷㫎㪿㪼㫅㩷㫋㪿㪼㩷㪩㪼㫋㫌㫉㫅㩷㪹㫌㫋㫋㫆㫅㩷㫀㫊㩷㫇㫌㫊㪿㪼㪻㪅
䋨䋶䋩㪛㪜㪭㪠㪚㪜㪃㩷㪠㪫㪜㪤㪃㩷㪸㫅㪻㩷㪛㪘㪫㪘㩷㪺㪸㫅㩷㪹㪼㩷㪻㫀㫊㫇㫃㪸㫐㪼㪻㩷㫌㫇㩷㫋㫆㩷㪼㫀㪾㪿㫋㩷㫃㫀㫅㪼㫊㩷㫆㫉㩷㫃㪼㫊㫊㪅
All manuals and user guides at all-guides.com

18
P50XR01U/E P60XR01U/E
HDD Check
1. Select a maintenance mode.
2. Next, select HDD.
3. It becomes the HDD check screen and the following items are displayed.
Total Size: It displays the total capacity of the HDD.
Used Size: It displays the consumption of the HDD.
Power-On Hours Count: The electricity time for HDD
Old Rec. Date: It displays the oldest date when TV recorded it to the HDD.
New Rec. Date: It displays the newest date when TV recorded it to the HDD.
Initial Date: It displays the date when TV initialised the HDD.
SMART Info.: It displays SMART of the HDD.
HDD Format: When you choose [HDD Format] and push "OK", TV initialises the HDD.
When initialisation is finished, TV displays it to right side indication as follows.
Normal end: OK
Abnormal end: NG
When you format the HDD, all the data in HDD are deleted.
HDD Log: You choose [SD] and push "OK", SD card acquire HDD log.
SMART information
[SMART info] displayed information and the poor HDD judgment standard are as follows.
When the behavior of the HDD is doubtful, please refer to this.
No item information indication range judgment standard
1 Raw Read Error Rate It displays error rate of the HDD.(decimal) 1~100 There is no problem more than 80.
2 Throughput Performance It displays Throughput performance.(decimal) 0~200 There is no judgment need.
3 Spin Up Time It displays Spin Up Time.(decimal) 0~100 There is no problem more than 50.
4 Start/Stop Count It displays Start/Stop Count.(decimal) (+)100~(-)100 Zero indication is a life guarantee limit.
There is no problem in a plus.
5 Reallocated Sector Count It displays Reallocated Sector Count.(decimal) 1~100 There is no problem more than 90.
6 Seek Error Rates It displays Seek Error Rates.(decimal) 1~100 There is no problem more than 80.
7 Seek Time Performance It displays Seek Time Performance.(decimal) 0~200 There is no problem more than 50.
8 Power-On Hours Count It displays Power-On Hours Count.(decimal) (+)100~(-)100 Zero indication is a life guarantee limit.
There is no problem in a plus.
9 Spin Retry Count It displays Spin Retry Count.(decimal) 50~100 There is no problem more than 80.
10 Device Power Cycle Count It displays Device Power Cycle Count. 1~100 There is no judgment need.
11 Power Off Retract Count It displays Power Off Retract Count. (+)100~(-)100 Zero indication is a life guarantee limit.
There is no problem in a plus.
12 Load/Unload Cycle Count It displays Load/Unload Cycle Count. (+)100~(-)100 Zero indication is a life guarantee limit.
There is no problem in a plus.
13 Device Temperature It displays temperature inside HDD at the ratio with
55 degrees. 253~100
Indication at the time of 100,
the HDD inside shows 55 degrees.
There is no problem more than 100.
14 Reallocation Event Count It displays Reallocation Event Count. 1~100 There is no problem more than 90.
15 Corrent Pending Sector Count It displays Corrent Pending Sector Count. 1~100 There is no problem more than 80.
16 Off-Line Scan Uncorectable
Sector Count It displays Off-Line Scan Uncorectable Sector Count. 1~100 There is no judgment need.
17 Ultra DMA CRC Error Count It displays Ultra DMA CRC Error Count. 1~200 There is no judgment need.
All manuals and user guides at all-guides.com

19
P50XR01U/E P60XR01U/E
Upgrading theSD
The procedure as follows.
1. Insert the MMC/SD card on which the firmware was written to the SD slot of the TV.
When obtained from an email and/or a FTP server, a PC and a commercial SD reader/writer are
necessary.
2-1 Select [menu] with a wireless remote controller.
2-2 Select [Initial Setup].
2-3 The Main software version will be display Vxxx.xxxx as shown on Fig. 1.
Fig. 1
2-4 Select [Upgrade (SD)].
2-5 Fig.2 will be displayed.
Fig.2
2-6 Select [Continue].
Select Return
Initial Setup
Softw are Mainte nance
Up g r ad e ( SD)
Up g r ad e ( OA D)
Auto Upgrade
Auto Picture Reset
Softw are Version 1.0000
On
Off
Enter
Confirm
㪪㫆㪽㫋㫎㪸㫉㪼㩷㫌㫇㪾㫉㪸㪻㫀㫅㪾㩷㫎㫀㫃㫃㩷㫊㫋㪸㫉㫋㪅㩷㪠㫋㩷㫄㫀㪾㪿㫋㩷㫋㪸㫂㪼
㫋㫀㫄㪼㩷㪽㫆㫉㩷㫋㪿㫀㫊㩷㫇㫉㫆㪺㪼㫊㫊㫀㫅㪾㪅
㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㩷㪘㫉㪼㩷㫐㫆㫌㩷㫊㫌㫉㪼㪖
Continue Cancel
Select Enter Cancel
All manuals and user guides at all-guides.com