HMS AnyBus-M User manual

Germany
Japan
Sweden
U.S.A

[email protected]om
[email protected]om
[email protected]m
[e-mail]

+ 49- 721 - 96472 - 0
+ 81- 45 - 478 -5340
+ 46- 35 - 17 29 20
+ 1 - 773 - 404 - 2271
HMS Industrial Networks
Fieldbus Appendix
AnyBus-M AS-Interface
Rev. 1.02

Preface About This Manual
How To Use This Manual................................................................................................................... P-1
Important user information ................................................................................................................ P-1
Related Documentation....................................................................................................................... P-1
Revision list ........................................................................................................................................... P-1
Conventions used in this manual ....................................................................................................... P-2
Support................................................................................................................................................... P-2
Chapter 1 About the AnyBus-M AS-Interface
Features ...................................................................................................................................................1-1
Compatible Products ............................................................................................................................1-1
Overview.................................................................................................................................................1-2
Connectors.....................................................................................................................................1-2
Indicators ......................................................................................................................................1-3
Chapter 2 Software Overview
Initialisation Sequence ..........................................................................................................................2-1
Operating Modes...................................................................................................................................2-1
I/O Data.................................................................................................................................................2-2
Chapter 3 Configuration Interface (RS232)
Menu Tree Overview ............................................................................................................................3-1
Enable Terminal Interface Menu...................................................................................................3-2
Main Menu ..................................................................................................................................3-2
View scan-lists..............................................................................................................................3-3
View all nodes ..............................................................................................................................3-4
View all detected nodes..................................................................................................................3-4
View single node ...........................................................................................................................3-5
Toggle mode...................................................................................................................................3-5
Online / Offline Mode..................................................................................................................3-5
Auto Address ...............................................................................................................................3-5
Save Configuration........................................................................................................................3-6
Alter Settings ..........................................................................................................................................3-6
Chapter 4 Mailbox Interface
Fault and Status Information...............................................................................................................4-1
Bus Control ............................................................................................................................................4-2
Set off-line / on-line mode (MB_SET_ON_LINE)...................................................................4-2
Set Running/Idle Mode & Data Representation (MB_SET_RUNNING_IDLE) .................4-3
Enable/Disable Automatic Address Programming (MB_SET_AUTO_ADDRESS) .............4-4
Set Protected/Configuration Mode (MB_SET_OPERATION_MODE).................................4-5
Table of Contents
Table of Contents

Table of Contents II
Configuration .........................................................................................................................................4-6
Set Slave Parameter (MB_SET_PARAM)................................................................................4-6
Set Slave Address (MB_SET_ADDRESS) ..............................................................................4-7
Get Slave Parameter (MB_GET_PARAMETER) ..................................................................4-8
Get Configuration for Slave (MB_GET_CONFIG)...................................................................4-9
Get ID Code for Slave (MB_GET_ID)....................................................................................4-10
Get I/O Configuration for Slave (MB_GET_IO).....................................................................4-11
Get Extended ID Code 1 from Slave (MB_GET_EXT_ID1) ................................................4-12
Get Extended ID Code 2 from Slave (MB_GET_EXT_ID2) ................................................4-13
Set Extended ID1 Code for Slave 0 (MB_SET_EXT_ID1)...................................................4-14
Get Parameter String from Slave (MB_GET_PARAMETER_STRING) ...........................4-15
Set Parameter String of Slave (MB_SET_PARAMETER_STRING) .................................4-16
Get ID String from Slave (MB_GET_ID_STRING) .............................................................4-17
Permanent Configuration...................................................................................................................4-18
Set Permanent Slave Parameter (MB_SET_NV_PARAM)...................................................4-18
Save Permanent Configuration for Slave in Non-Volatile Memory (MB_SET_NV_CONFIG)4-19
Get Permanent Slave Parameter (MB_GET_NV_PARAM).................................................4-20
Get Permanent Configuration for Slave (MB_GET_NV_CONFIG)......................................4-21
Save Current Slave Parameters in Non-Volatile Memory (MB_SAVE_PARAM).................4-22
Save Current Slave Configuration in Non-Volatile Memory (MB_SAVE_CONFIG)............4-23
Analog Data..........................................................................................................................................4-24
Get Analog Input from Slave (MB_GET_ANA_INPUT) ....................................................4-24
Set Analog Output for Slave (MB_SET_ANA_OUTPUT) ..................................................4-25
Network Status ....................................................................................................................................4-26
Get Status Lists from Network (MB_GET_LISTS) ...............................................................4-26
Diagnostics ...........................................................................................................................................4-27
Get Diagnostic String from Slave (MB_GET_DIAG_STRING) ...........................................4-27
Chapter 5 Fieldbus Specific Area
Memory Map................................................................................................................................5-1
LPS - List of Configured Slaves (address 640h - 647h, Read Only) .............................................5-2
LAS - List of Activated Slaves (address 648h - 667h, Read Only)..............................................5-2
LDS - List of Detected Slaves (address 668h - 677h, Read Only)................................................5-2
DELTA List (address 678h - 687h, Read Only) .......................................................................5-3
LPF - List of Peripheral Faults (address 688h - 697h, Read Only) .............................................5-3
AS-Interface Status Flags (address 698h - 699h) .........................................................................5-4
Node Status (address 69Ah - 6D9h) ...........................................................................................5-4
Node I/O Configuration (address 6DAh - 719h) ........................................................................5-4
Node ID Code (address 71Ah - 759h).........................................................................................5-5
Node Parameter (address 75Ah - 799h).......................................................................................5-5
Config Mode (address 79Ah)........................................................................................................5-5
Running / Idle Mode (address 79Bh) ...........................................................................................5-5
Byte / Nibble Mode (address 79Ch).............................................................................................5-5

Table of Contents III
Chapter 6 Troubleshooting
General....................................................................................................................................................6-1
Configuration Interface ........................................................................................................................6-1
Appendix A Environmental Specification
Temperature ..........................................................................................................................................A-1
Relative Humidity.................................................................................................................................A-1
EMC compliance..................................................................................................................................A-1
Appendix B Connectors
Configuration Interface ....................................................................................................................... B-1
Fieldbus Interface.................................................................................................................................B-2
Appendix C Electrical Characteristics
Supply Voltage ......................................................................................................................................C-1
Power Consumption ............................................................................................................................C-1
PE Grounding.......................................................................................................................................C-1
Appendix D Mechanical Specification
Measurements, PCB............................................................................................................................ D-1
Measurements, Connectors & Switches........................................................................................... D-2
Standard Configuration............................................................................................................... D-2

Preface
About This Manual
How To Use This Manual
This manual provides an overview of the AnyBus-M AS-I Master and is in intended to be used in cun-
junction with the AnyBus-M Design Guide.
The reader of this document is expected to have basic knowledge in the AS-Interface network system,
and communication systems in general.
Important user information
The data and illustrations found in this document are not binding. We reserve the right to modify our
products in line with our policy of continuous product development. The information in this document
is subject to change without notice and should not be considered as a commitment by HMS Industrial
Networks AB. HMS Industrial Networks AB assumes no responsibility for any errors that may appear
in this document.
There are many applications of this product. Those responsible for the use of this device must ensure
that all the necessary steps have been taken to verify that the application meets all performance and safe-
ty requirements including any applicable laws, regulations, codes, and standards.
AnyBus® is a registered trademark of HMS Industrial Networks AB. All other trademarks are the prop-
erty of their respective holders.
Related Documentation
Revision list
Document name Author
The Complete AS-Interface Specification AS-International Association Germany
Master Profiles (Anex B to the Complete AS-Interface Specification) v2.0 AS-International Association Germany
AnyBus-S Paralllel Design Guide HMS Industrial Networks AB
Revision Date Author Chapter Description
1.00 2002-09-24 PeP All Created
1.01 2002-11-04 TTh 1 Updated LED’s
1.02 2003-10-29 PeP All Minor corrections

About This Manual P-2
Conventions used in this manual
The following conventions are used throughout this manual:
• Numbered lists provide sequential steps
• Bulleted lists provide information, not procedural steps
• The term ‘module’ is used when referring to the AnyBus module
• The term ‘application’ is used when referring to the hardware that is connected to the AnyBus
Application Connector
• Hexadecimal values are written in the format NNNNh, where NNNN is the hexadecimal value.
Support
HMS Sweden
Email: [email protected]
Tel: [phone]
Fax: [phone]
Online: www.hms-networks.com
HMS America
Email: [email protected]
Tel: [phone]
Fax: [phone]
Online: www.hms-networks.com
HMS Germany
Email: [e-mail]
Tel: [phone]
Fax: [phone]
Online: www.hms-networks.com
HMS Japan
Email: [email protected]
Tel: [phone]
Fax: [phone]
Online: www.hms-networks.com

Chapter 1
About the AnyBus-M AS-Interface
The AnyBus-M AS-I Master implements all functionality of the Reduced Extended Master (M2e) profile
as well as some functions of the Full Extended Master(M1e) profile.
The module can manage up to 62 AS-I slaves and it complies to the AS-Interface 2.1 specification. It
supports analog slaves according to slave profiles 7.3 and 7.4 (Consult the AS-Interface Slave Profiles
Specification for more information), and provides data exchange using the standard AnyBus-S applica-
tion interface. Additionally, the module features dedicated mailbox commands for accessing 7.4 slaves.
As for all AnyBus-M modules it is also possible to configure the network via the application interface.
Features
• Manage up to 62 slaves
• Up to 248 digital inputs and 186 digital outputs
• Up to 124 (16 bit) analog values
• Galvanically isolated bus electronics
• Easy to use, text based Configuration Interface via on board RS232 port
• Automatic Slave 0 Address Programming
• Complete access to network configuration via application interface
• Analog slave profile 7.1 and 7.2
• Analog slave profile 7.3 and 7.4
Compatible Products
This product is a member of the AnyBus concept of interchangeable fieldbus modules. This makes it
fully interchangeable with any fieldbus system supported by the AnyBus-M platform.

About the AnyBus-M AS-Interface 1-2
Overview
Connectors
Application Connector
The application connector features a standard AnyBus-M 2kbyte parallel DPRAM interface. For further
information, please consult the general AnyBus-M Design Guide.
AS-Interface Connectors
The module supports both 5.08 pluggable screw connectors and board to board connectors.
For more information about connectors and pin assignments, see Appendix B-1 “Connectors”
Configuration Interface
This Configuration Interface provides a simple text based user interface for use with a PC. No special
software is required except for a standard terminal emulatior.
For connector pinout and cable schematic, see Appendix B-1 “Connectors”
# Description
1 Application Connector
2 Fieldbus Connectors
3 Configuration Interface
4 Status Indicators
5 AnyBus Watchdog LED
6 AS-Interface Watchdog LED
2
3
4
1
6
5

About the AnyBus-M AS-Interface 1-3
Indicators
AS-Interface Watchdog
•Flashing
The AS-Interface is working properly.
•Off
Module not initialised or AS-Interface network not working properly.
AnyBus Watchdog
Consult the general AnyBus-M Design Guide for further information.
Status Indicators
These leds indicate run time status and errors to the user.
Note: If the module receives the mailbox command SW_RESET (i.e a soft reset) all 4 leds will flash red
4 times.
Led State Description
1 - Running / Idle Green Module is in running mode
Red Module is in idle mode
2 - Network Status Off No power or not initialised
Flashing Green On line according to configuration
Green On line, but no connections established
Red Offline
3 - Module Status Off No power or not initialised
Flashing Green Protected mode
Green Configuration mode
Red Power Fail bus
4 -Auto prog, slave 0 exist Off No error, no slave 0, autoprogramming not possible
8Hz Green Auto programming possible
1Hz Green Slave address 0 exist
Red Periphery error
8Hz Red Periphery error, auto-programming possible
1Hz Red Periphery error, slave with address 0 exist
12
43