Hobo RXW-WL Series User manual

RXW Water Level Sensor Interface (RXW-WL-xxx) Quick Start
28083-B MAN-QSG-RXW-WL
Adding a Sensor Node to the HOBOnet® Wireless Sensor Network
Important: Keep the sensor node near the station while completing these
steps.
If you are setting up a new station, follow the instructions in the station
quick start guide before setting up this sensor node (go to
www.onsetcomp.com/resources/documentation/24380-man-rx2105-
rx2106-qsg for RX2105 and RX2106 stations or
www.onsetcomp.com/resources/documentation/18254-man-qsg-rx3000
for RX3000 stations).
1
2
3
Connect the interface connector to the sensor with the
direct-read cable in between as shown here. The end
of the cable with the longer housing connects to the
interface connector as shown below.
4
5
Watch the sensor node LCD while it joins the network:
6
7
Go to www.hobolink.com to
monitor the status and health of the sensor node. See
the HOBOlink Help for details.
Press the Search button on the station. The magnifying
glass icon blinks while the station is in search mode
waiting for sensor nodes to join the network.
Press the Select button on the station to switch to the
module with the manager (module 2 on RX2105 or
RX2106 stations).
Open the door on the sensor node and install the
rechargeable batteries. Press the button on the
sensor node for 3 seconds.
Press the Search button on the station again
to stop the search for sensor nodes.
This signal strength icon
blinks while the sensor
node searches for a
network.
Once the sensor node finds a
network, the icon stops
blinking and the bars cycle
from left to right.
a.
b.
c.
d.
This network connection
“x” icon blinks while the
sensor node completes
the registration process,
which may take up to
five minutes.
Once the sensor node has
finished joining the network,
the “x” icon no longer
appears. The channel count
on the station LCD increases
by four.
Interface
Connector
Plug this part of the cable
with the longer housing into
the interface connector and
screw it to hand tighten.
Plug this part of the cable with the
shorter housing into the sensor
end and screw it to hand tighten.
Sensor end

U.S. and International Sales: 1-508-759-9500 2 www.onsetcomp.com
Installing the Bracket and Sensor Node
1
Orient the bracket so the text TOP is facing
upwards.
2
To install the bracket onto a wall, use
the two long screws included in the
package. Screw the bracket to a wall
using the two holes on the mid-section
of the bracket.
3
To install the bracket
onto a pole, slip a cable
tie through each of the
channels on the bracket
and fasten the tie
around the pole.
4
Insert the bottom of the
sensor node into the retaining
clips on the bottom of the
bracket then press the top of
the sensor node into the clips
at the top of the bracket.
5
Use the short screw
included in the package to
fasten the sensor node to
the bracket.
6
Close the sensor node and use a padlock to keep it secure.
Note: Ensure that the node seal is clean from foreign
debris.
Mounting and Positioning the Sensor Node
•Position the sensor node towards the sun, making sure
the solar panel is oriented so that it receives optimal
sunlight throughout each season. You may need to
periodically adjust the position of the sensor node as the
path of the sunlight changes throughout the year or if
tree and leaf growth alters the amount of sunlight
reaching the solar panel.
•Make sure the sensor node is mounted a minimum of 1.8
m (6 feet) from the ground or vegetation to help
maximize distance and signal strength.
•Consider using plastic poles such as PVC to mount the
sensor node as certain types of metal could decrease the
signal strength.
•Place the sensor node so there is full line of sight with
the next sensor node. Use a repeater if there is an
obstruction between sensor nodes.
•There should not be more than five sensor nodes in any
direction from a repeater or the manager. Data from
sensor nodes travels or “hops” across the network and
may not reach the station if the sensor node is more
than five hops away.

U.S. and International Sales: 1-508-759-9500 3 www.onsetcomp.com
Deploying the Water Level Sensor
Warning: Do not suspend anything from the 6-foot
cable. The 6-foot cable is not designed to support
the weight of the direct-read cable and sensor.
Suspending the direct-read cable and water level sensor
•Option 1 (preferred): Using the long direct-read cable
(CABLE-DR-xxx) and a compatible well-cap
•Option 2: Using the mounting hole on the endcap
The endcap contains a loop that allows you to use a
carabiner (rated to 50 lbs. or grater) or some other
reliable method to suspend the interface connector.
Water Level Scaling in HOBOlink
The following sections provide information on how to
measure the reference water level and account for water
density.
Scenario 1: Setting a Reference Water Level
1. Deploy the water level sensor in water and secure
it in position (for example, hang it in a well).
2. Make sure your RX Station is logging and
connecting fast enough for you to see the current
water depth readings. (Press connect on the RX
Station to see the latest logged value).
3. Enable Scaling for the HOBOnet water level sensor.
In HOBOlink:
a. Select Devices, RX Devices, then select your
station.
b. Select the wrench at the top of the page and
select Module/Sensor Configuration from the
menu.
c. Select Water Level for the appropriate sensor. On
the right side of the page, ensure that Enable
Scaling is selected.
4. Enter the scaling values:
a. Enter the Scaled Units: for example meters or
feet. This should match the units shown in
Latest Value, or you will need to adjust the
multiplier to convert.
b. Enter the multiplier in the Multiplier field.
Multiplier*
Fresh water
1
Brackish water
0.99
Salt water
0.9765
c. Enter 0 in the Offset field for now.
d. Enter the Scaled Measurement Type, for
example “Pond Water Level”.
5. Click save and note the Latest Value.
6. Take a reference water level measurement.
•Note this as a negative number if the water
level surface is below the reference point,
such as groundwater level referenced to the
top of the well (Figure 1).
•Note this as a positive number if the water
level surface is above the reference point,
such as the bottom of the stream or the zero
on a staff gauge (Figure 2).
Route the direct-read cable through the
posts of the well-cap to secure the cable.
CABLE-DR-xxx
WELL-CAP-02 (shown as
an example)
6-foot cable
Note: When this option is used, the interface
connector is outside of the well.
Mounting Hole
Example using a carabiner
with WELL-CAP-02

U.S. and International Sales: 1-508-759-9500
www.onsetcomp.com/contact/support
© 2019–2023 Onset Computer Corporation. All rights reserved. Onset, HOBO, HOBOlink, and HOBOnet are registered trademarks
of Onset Computer Corporation. All other trademarks are the property of their respective companies.
This product has been manufactured by Onset Computer Corporation and in compliance with Onset’s ISO 9001:2015 Quality
Management System.
28083-B MAN-QSG-RXW-WL
7. Calculate the offset, which is equal to the
reference water level reading (from step 6) minus
the current water depth reading (from HOBOlink in
step 5).
8. Enter the calculated offset in the Offset field.
9. Click save.
10. Verify latest value matches the correct water level.
Scenario 2: Measuring Water Depth (Figure 3)
1. Ensure the water level sensor is in the air.
2. Make sure your RX Station is logging and
connecting fast enough for you to see the current
water depth readings. (Press connect on the RX
Station to see the latest logged value).
3. Enable Scaling for the HOBOnet water level sensor.
In HOBOlink:
a. Select Devices, RX Devices, then select
your station.
b. Select the wrench at the top of the page
and select Module/Sensor Configuration
from the menu.
c. Select Water Level for the appropriate
sensor. On the right side of the page,
ensure that Enable Scaling is selected.
(Refer to the screen shot in step 3 of the
previous section.)
4. Enter the scaling values:
a. Enter the Scaled Units: for example
meters or feet. This should match the
units shown in Latest Value, or you will
need to adjust the multiplier to convert.
b. Enter the multiplier in the Multiplier
field.
Multiplier*
Fresh water
1
Brackish water
0.99
Salt water
0.9765
c. Enter 0 in the Offset field for now.
d. Enter the Scaled Measurement Type, for
example “Pond Water Level”.
5. Click save and note the Latest Value.
6. Calculate the offset, which is equal to zero minus
the current water depth reading (from step 5).
7. Enter the calculated offset in the Offset field.
8. Click save. Latest value should be zero.
9. Deploy the water level sensor in water and secure
it in position (for example, hang it in a well).
Figure 1: Water level is below reference point
Figure 2: Water level is above reference point
Figure 3: Water level is above pressure sensor
For specifications, complete mounting guidelines,
and other details about this sensor node, refer to
the full product manual. Scan the code at left or
go to:
www.onsetcomp.com/resources/documentation/28084-User-
Guide-RXW-WL
*The Multiplier represents the density of the water, which is a function of its salinity. This is equal to 1 divided by the true density of the water in g/cm3
(e.g., 1/1.025 for typical salt water).