Homech HM-HF008 User manual

Inflatable Stand
Up Paddle
Board
User Manual
www.homech.net
HM-HF008

CONTENTS
IMPORTANT SAFETY INSTRUCTIONS
KNOWING YOUR SUP BOARD
GETTING STARTED
STORAGE AND MAINTENANCE
TROUBLESHOOTING
01
03
05
11
13
THANK YOU FOR CHOOSING HOMECH INFLATABLE
STAND UP PADDLE SUP BOARD. BE SAFE AND HAVE FUN!

IMPORTANT
SAFETY
INSTRUCTIONS
Familiarize yourself with the features and ask for professional training if you are
inexperienced in handling this type of board. For your full enjoyment it is important to
follow proper safety procedures and rules of the waterway that apply to all SUPs.
01 02
WARNING
Always wear a Coast Guard
approved Personal Flotation
Device (PFD).
Never go boarding in severe
conditions. Beware of offshore
winds and currents.
DO NOT leave the board
exposed to direct sunlight for
extended periods of time.
Keep away from fire.
DO NOT use around sharp objects.
Never allow minors to use without adult supervision.
DO NOT paddle the board while impaired or under the influence of intoxicants such as
alcohol or drugs.
DO NOT use the board for anything other than its intended use.
Always exercise safe boarding and do not attempt actions which are beyond your
skills or ability.
Never paddle the board after sunset, before dawn or at any time in poor lighting.
Before every use, carefully check for any sign of wear or leakage to ensure the SUP is
in good condition. DO NOT use if any damage is found.
DO NOT use high pressure air pump to inflate. Inflate according to the rated pressure or
it will cause over inflation and/or an explosion.
Check your local regulations to familiarize yourself with any rules or regulations that
may apply to water sports and watercrafts.
We recommend that you always paddle with a partner -it's safer and more fun!
READ AND SAVE THESE INSTRUCTIONS

03 04
KNOWING
YOUR
SUP BOARD
Unpack and check that all accessories are inside.
Secure Bungee
(Cargo Area)
Carry Handle
D-Rings
(Secure Seat)
D-Ring
(Secure Safety
Leash)
Air Valve
Adjustable
Paddle Backpack
Dual Action
Hand Pump
Snap-in Fin Safety Leash Waterproof
Bag
Repair Kit
Valve
Wrench
Repair
Patch
Repair
Glue
Valve Adapter
(Standard Valve for
Car and Bicycle Tires)
Pump
Base
Pump Hose
12
3
4
5
6 7 8
9

05 06
GETTING
STARTED
Dual Action Hand Pump
Assembly of Handles
Screw in two handles.
Assembly of Base
Align and twist to lock.
1
2
12 1 2
DEFLATE
Port
INFLATE
Port
Inflating / Deflating
Screw the pump hose onto
the INFLATE / DEFLATE port.
Adjusting Pressure Level
· 0-2psi -> Level 1 · 3-6psi -> Level 2
· 7-12psi -> Level 3
Pressure
Gauge
Pressure
Level
1. 2. Use of Pump

Insert the other end to the
air valve and twist clockwise.
1
2
Screw the pump hose
onto the INFLATE port.
1
2
07 08
Installing the FinInflating the SUP Board
Unroll the paddle board on level
ground with the air valve facing up.
1. 2. 3.
Remove the valve cap and
ensure the pin is in the Up position.
4. 5. 6.
Pump the board with steady strokes
until the pressure gauge reads 10-12psi.
Screw on the cap.
(It is normal that you will hear a small
burst of air when removing the hose.)
IMPORTANT
DO NOT
exceed 15 psi.
Flip the
board upside down.
1. 2. 3. 4.
Make sure the fin is secured before paddling.
Remove the
anti-deformation gasket.
Slide the fin into
the notched section.
Lock the fin by
inserting the clip into the hole.
Assembling the Paddle
Connect the two paddle
shafts until they click into place.
1. 2. 3.
Open the quick-lock,
adjust to desired height.
Lock into place by
pressing the quick-lock.
165
66
1
2
165
66

09 10
Attaching the Safety Leash
For your own safety when paddling, remember to attach the safety leash
to the front D-Ring and fasten to your ankle.
Repairing Leaks & Tears
Leaking Valve
Screw tight with valve wrench.
1
2
Tears (< 10 mm)
1. Deflate the board completely.
2. Locate the leak. Wipe clean and dry.
3. Cut a suitable size of patch.
Apply glue to the plain side.
4. Apply glue to the leak on board,
wait for 1 minute.
5. Attach over the tear and hold for 2 minutes.
6. Wait 48 hours before re-inflating.
Repair
Patch
Repair
Glue

STORAGE
AND
MAINTENANCE
Disassembling the Fin
Press down to remove the clip.
1. 2. 3.
Slide the fin out of its base. Insert the anti-deformation gasket.
1
2
Deflating the SUP Board
Remove the valve cap.
1. 2. 3.
Press down on the pin to deflate. Exhaust the remaining air by
connecting the pump hose to the air valve.
1
2
11 12
For storage, you may roll up the board and store with all accessories
in the included backpack.

QA
Which direction should be the “Homech”
logo face when paddling?
It is easier to paddle with the logo facing towards the front of the board.
This allows the water to slip more easily past the blade as it moves
through the water.
Can I keep my board inflated? If you choose to leave the board in direct sunlight for an extended period
of time it is recommended that you deflate the board to prevent
over-expansion as this is not covered under the warranty.
Winter is here, how do you suggest
I store my board?
We recommend storing it completely dry, rolled up in the bag, stored in a
location away from the elements such as a garage or shed.
How should I clean my board? Soapy water should do the trick! We also like to use mineral spirits for
those tougher stains.
Do I have to wear a lifejacket? The US Coast Guard requires a PFD to be on board your paddle board
since it is considered a vessel.
TROUBLE
SHOOTING
13 14
The following troubleshooting guide addresses the most
common problems. If problems persist, feel free to contact
our Customer Support at [e-mail].

NORTH AMERICA
E-mail: [e-mail](US)
[e-mail](CA)
WARRANTY
AND SERVICE
Thanks for choosing Homech SUP Board.
This product is covered with Homech product
and labor warranty for 12 months from the date
of its original purchase.
We can only provide after sales service for products
that are sold by Homech or Homech authorized retailers
and distributors. If you have purchased your unit from a
different place, please contact your seller for return and
warranty issues.
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology Development Co.,Ltd.
Address: Floor 7, Building E, Galaxy World Phase II, Shenzhen, China
Rev_1.0_EN

尺寸：210*140MM
装订成册
材质：封面128克铜版纸，内页80克书纸