HomeGuardian 4902013 User manual
Installation and operating instructions
4902001/2/4/8/9/12/13 are only compatible to our main security system 4902000 (HWS100) ONLY.
Under the alarm mode, once the
main control unit receive the signal from any sensors, it will send a signal to the auto dialer at the
same time. Once the auto dialer receive it and was triggered by an emergency,
Remarks: *The dialer is not applicable to the ISDN, ADSL switch board phone connections.
5
SECTION 4 – ACTIVATING THE DIALER
Congratulations.YourAutoDialerplusisnowreadytohelpinemergencysituations.Youcan
test how the Dialer works by pressing both # and * keys on the dialer’s keypad for the dialer
to dial out to the phone numbers you have stored.
SECTION 5 - INSTRUCTION FOR THE RECIPIENT
There are several things that your call recipients should know in order to successfully receive
andterminateanemergencycallfromyourdialer.Makesureyourdialerrecipientsunder-
stand what to do when they receive your emergency call. Therefore, it is a good idea to give
them a copy of this page for their reference.
5.1 To START speakerphone conversation
After having fully listened to the recorded message, press the pound sign, to confirm that
themessageisNOTmerelydeliveredtoavoicemail.The“Listening-in”functionpress“1”and
“Speaking-in”function press “ 3 ”can only be used when the call recipient pressed the pound
key(#).Timeoutperiodis60secondsandrecipientscanextendeitherthelisteningtime
or speaking time by pressing “1”or “ 3 ”accordingly. Each time they are pressed a further 60
seconds will be allowed by the Auto Dialer.
5.2 To EXTEND the time out for speakerphone conversation
Timeoutperiodis60seconds;therecipientcanextendthetimeoutforanother60 seconds
by pressing (1) to listen-in and (3) to speak-in. The conversation will be disconnected if the
dialer receives no instruction.
5.3 To STOP the emergency message of the existing call AND all the
remaining calls
Whenthemessageisnished,press(#).Thiswillstopthedialerfromcallingexistingnumber
and all the remaining phone numbers.
Since this termination will stop the dialer from calling all the phone numbers, the recipient
mustknowexactlythesituationandemergencyofthecallbeforeterminatingit.
5.4 To DISCONNECT all calls after conversation
Oncethespeakerphoneconversationisover,therecipientshoulddisconnectthecallby
pressing (#) instead of just hanging up the phone. This will terminate the connection for all
existingcallandtheremainingcalls.
6
SECTION 6 - HOUSE SECURITY CODE AND ZONE CODE SETTINGS
Youcanchangethehousesecuritycodeoneachsensor,panelandothermodulesofyour
security system to avoid interference with other systems.
InmostcasesyouwillNOTneedtochangethefactorysettingsofthehousesecuritycode.If
the Panel and sensors activate intermittently or do not work at all, you may be able to solve
the problem by changing the house security codes on all system modules.
Step1:Thereare4jumpers/dip-switchesoneachdevice.Removethejumpercompartment
cover, then pull out the Jumper to change the house security code setting and make sure the
jumpersonthePanelanditsensorsmatchexactly.
Jumpersforhouse •Panel
securitycode •Eachsensor
Defaulthousecode:1:ON,2:ON,3:ON,4:ON
*Jumper:ON=Plugged,OFF=PullOut
Dip-Switchesforhouse •SystemController
securitycode Defaulthousecode:1:ON,2:ON,3:ON,4:ON
SECTION 7 - MAINTENANCE
The product may be cleaned with a soft damp cloth and then wiped dry. Do not use
abrasive,solventbasedoraerosolcleanersasthismaydamageand/ordiscolourtheproduct.
Do not allow water to enter or attempt to clean inside the unit.
SECTION 8 - BATTERIES
Do not allow batteries to corrode and leak as this may cause permanent damage to the
product. Take care to insert the batteries with the correct polarity as shown inside the battery
compartments.Donotmixnewandoldbatteriesordifferenttypesofbatteries.Donott
rechargeable batteries.At the end of their useful life the batteries should be disposed of via a
suitableRecyclingCentre.Donotdisposeofwithyournormalhouseholdwaste.DONOTBURN.
ON
ON
ON
4
4
DIP
3
3
2
2
1
1
IC Caution Statement
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This product meets the applicable Industry Canada technical specifications.
Before the installation of this equipment, the users should assure that the equipment is allowable
to be connected to the facilities of the local communications company. It must also be installed
using an acceptable method of connection. In some cases, some company's inside wiring
associated with the switchboard phone connections. The customer should be aware that
compliance with the above conditions might not prevent the degradation of service in these
situations.
If you experience trouble with this equipment, for repair or warranty information, contact an
authorized Canadian maintenance facility designated by the seller. If the equipment is causing
harm to the telephone network, the telephone company may request that you disconnect the
equipment until the problem is resolved.
8
If your home has specially wired alarm equipment connected to the telephone line, ensure the
installation of this equipment does not disable your alarm equipment. If you have questions
about what will disable alarm equipment, consult your telephone company or a qualified
installer.
"The Ringer Equivalence Number (REN) is an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination of an interface may consist of
any combination of devices subject only to the requirement that the sum of the RENs of all the
devices does not exceed five."
pound sign
9
10
11
Installation et instructions d’opération
4902001/2/4/8/9/12/13 sont compatibles avec notre système de sécurité principal 4902000 (HWS100) SEULEMENT
Under
the alarm mode, once the main control unit receive the signal from any sensors, it will send a
signal to the auto dialer at the same time. Once the auto dialer receive it and was triggered by
an emergency, it will silently send a pre-recorded message to up to 8-pre-programmed
telephone numbers with the first 2 numbers being the priority phone number.
Remarks: *The dialer is not applicable to the ISDN, ADSL switch board phone connections.
Son fonctionnement est soumis aux deux conditions suivantes :
1. Ce dispositif ne peut causer aucune interférence nuisible et
2. Ce dispositif doit accepter toute interférence reçue, y compris une interférence pouvant causer
un fonctionnement non désiré.
Avertissement IC
8
This product meets the applicable Industry Canada technical specifications.
Before the installation of this equipment, the users should assure that the equipment is allowable
to be connected to the facilities of the local communications company. It must also be installed
using an acceptable method of connection. In some cases, some company's inside wiring
associated with the switchboard phone connections. The customer should be aware that
compliance with the above conditions might not prevent the degradation of service in these
situations.
If you experience trouble with this equipment, for repair or warranty information, contact an
authorized Canadian maintenance facility designated by the seller. If the equipment is causing
harm to the telephone network, the telephone company may request that you disconnect the
equipment until the problem is resolved.
If your home has specially wired alarm equipment connected to the telephone line, ensure the
installation of this equipment does not disable your alarm equipment. If you have questions
about what will disable alarm equipment, consult your telephone company or a qualified
installer.
"The Ringer Equivalence Number (REN) is an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination of an interface may consist of
any combination of devices subject only to the requirement that the sum of the RENs of all the
devices does not exceed five."
Press and hold for 2 seconds, until the
REC shows up on the screen to start the
recording.
Recording will finish when you press the
again or the recording reached 20 seconds.
To PLAYBACK
message
Press and release the to play back the
recorded message
Press to activate the keyboard
Enter the 4-DIGIT PIN (Default PIN is "1234")
Press to go into SETUP mode
To CHECK
PHONE
NUMBERS
Press (Display will show "1" for 1st
phone number).
Press again for checking the rest phone
numbers
Make sure to include information marked " * "
for sending proper message and instruction for
help
Example of the message:
This is a security alert from [ *your resident or
business name here ], at [ *your address here ].
*After having fully listened to this message,
please press the pound sign (#) and press " 1 "
for listening, " 3 " for speaking and so forth. Over.
To RECORD
an effective
message
To
ENTER/STORE
PHONE
NUMBERS
Press (Display will show "1" for 1st phone
number),repeat this step to choose which
phone numbers you wish to program (1, 2, 3,
4, 5, 6, 7, 8)
Press and enter the phone number
digits (Maximum 16 digits)
Press to clear number enter wrongly
and re-enter thephone number digits again
Press to finish
Step 1.
Enter setup
mode for any
programming
To ENTER
SETUP mode
Step 2.
Under
SETUP
mode
To RECORD
message
9
Table of contents
