Safety 1st 48390 User manual

ANTES DE COMENZAR:
• Lea todas las instrucciones antes de instalar.
• Guarde estas instrucciones para su uso futuro.
• Retire todo el contenido del embalaje y deseche la caja y/o las bolsas de polietileno.
• Despliegue e identifique todas las piezas.
• No devuelva este producto al lugar donde lo compró. Si falta alguna pieza,
envíe un correo electrónico a [e-mail], llame al Departamento de
Relaciones con el Consumidor al [phone], o envíe un fax al
[phone]. También puede visitar nuestro sitio web en www.safety1st.com.
Tenga a mano el número de modelo (48390, 48444, HS204) y el código de
fecha (fecha de fabricación), que se encuentran indicados en el paquete.
• No se recomienda el uso de herramientas eléctricas para la instalación de tornillos.
HERRAMIENTAS NECESARIAS: • Destornillador Phillips
• Tijeras y cinta adhesiva
Información de seguridad importante
Después de su colocación, verifique que funcione correctamente tirando firme-
mente de la puerta o el cajón. Si el pestillo no sujeta firmemente la puerta o el
cajón al tirar de estos, ajuste la altura del pestillo para lograr una unión segura.
Un niño sin supervisión puede ser capaz de inutilizar la protección que ofrece
este producto. Para que este producto funcione efectivamente durante más
tiempo, evite que los niños vean como se opera. Si los niños ven cómo usted
libera una traba, un pestillo o una cubierta, podrían aprender más rápido la
manera de inutilizar cualquier tipo de dispositivo de seguridad.
A A
B B
C C
Latch
Catch
Screws (4 per lock)
Template (Carefully cut template at the solid line.)
D D
©2014 Dorel Juvenile.
www.djgusa.com [phone] www.safety1st.com
Made in CHINA. Hecho en CHINA. Styles and colors may vary. Los estilos y los colores pueden variar.
Distributed by (distribuido por) Dorel Juvenile Group, Inc., 2525 State St., Columbus, IN 47201-7494
Dorel Juvenile Canada, 873 Hodge, St. Laurent, QC H4N 2B1
09/29/14 4358-6224B
Cabinet & Drawer Latches
48390, 48444, HS204 User Guide
Pestillo para armarios y cajones
48390, 48444, HS204 Guía del Usuario
Parts & Terms Used Piezas y términos utilizados
BEFORE YOU BEGIN:
• Read all instructions before installing.
• Keep these instructions for future use.
• Remove all contents from packaging and discard box, and/or poly bags.
• Lay out and identify all parts.
• Do not return this product to the place of purchase. If any parts are
missing, email [e-mail], call Consumer Relations at
[phone], or fax at [phone]. You can also visit our website
at www.safety1st.com. Have the model number ready (48390, 48444,
HS204) and date code (manufacture date) located on package.
• P ower tools are not recommended for screw installation.
TOOLS NEEDED: • Phillips head screwdriver
• Scissors and tape
Important Safety Information
Check for security after installation by tugging firmly on the door or drawer.
If the latch does not securely hold the door or drawer when tugged, adjust
the latch height to obtain a secure connection.
Your child will eventually be able to defeat this product. To keep this
product effective for as long as possible, avoid letting children see how
you operate child safety devices. Watching you disengage a lock, latch or
cover could enable them to learn sooner how to defeat it.
CAUTION: This product is only a deterrent. It is not a substi-
tute for proper adult supervision.
DO NOT use product if damaged or broken.
FOR INDOOR HOME USE ONLY.
PRECAUCIÓN: Este producto es sólo un elemento disuasivo. El
mismo no reemplaza la supervisión adecuada por parte de un
adulto.
NO utilice este producto si se encuentra roto o dañado.
PARA USO DOMÉSTICO ÚNICAMENTE EN INTERIORES.
WARNING:
• Do not use this product to guard against toxic and
dangerous substances, or sharp-edged or pointed objects.
Such materials should always be placed “high up” or
otherwise made completely inaccessible to children.
• ADULT INSTALLATION REQUIRED. KEEP SMALL
PARTS AWAY FROM CHILDREN DURING
INSTALLATION.
AVISO:
• No utilice este producto para evitar que los niños ten-
gan acceso a sustancias tóxicas y peligrosas u objetos
punzantes y cortantes. Tales materiales siempre deben
colocarse en lugares “altos” u otros lugares a los que
los niños no puedan llegar de ninguna manera.
• REQUIERE INSTALACIÓN POR PARTE DE UN ADULTO.
MANTENGA LAS PIEZAS PEQUEÑAS FUERA DEL ALCANCE
DE LOS NIÑOS DURANTE LA INSTALACIÓN.
Pestillo
Enganche
Tornillos (4 por traba)
Plantilla (Corte cuidadosamente la plantilla por la línea llena.)
1
AB
C
Front edge of cabinet opening
Carefully cut template at the s
olid line.
Carefully cut template at
the solid line.
Carefully place
template
according to
instructions and
then mark two X
locations.
1.063” (x.xcm)
Front edge of cabinet opening
Corte cuidadosamente la
plantilla por la línea llena.
Corte cuidadosamente la
plantilla por la línea llena.
Coloque
cuidadosamente
la plantilla según
las instrucciones
y luego marque
la posición de las
dos X.
1.063” (x.xcm)
Installation
Template
Front edge of
cabinet opening
D
D

Pestillo:
1 Corte cuidadosamente la plantilla por la línea llena y
perfore los dos agujeros X .
2 Haga una línea en la plantilla con el enganche, de
manera que la línea punteada esté a nivel con el borde
delantero de la abertura del armario. Fije la plantilla al
armario con la cinta adhesiva (Figura 2).
3 Cierre la puerta/cajón del armario y marque los bordes
exteriores de la plantilla en la puerta/cajón del armario
y en el borde superior de la plantilla (Figura 3). Quite
la plantilla.
4 Line the template up between the two marked edges
on the cabinet door/drawer with the marked lines on
the top edge of the cabinet door/drawer and tape
(Figure 4).
5 Mark the template hole locations on the cabinet door/
drawer. Remove the template and predrill holes with
a 1/16” (1.5mm) drill bit.
6 Secure latch tightly with screws.
NOTE: Cabinet door/drawer should not open more
than 2” (5.08cm).
Latch:
1 Carefully cut template at the solid line and punch out
the two holes X .
2 Line the template up with the catch so that the
dotted line is flush with the front edge of cabinet
opening. Tape template to cabinet (Figure 2).
3 Close the cabinet door/drawer and mark the outer
edges of the template on the cabinet door/drawer
and top edge on the template (Figure 3). Remove the
template.
To Install Para instalar
2
1. Line up catch to the front edge of
the door/drawer opening.
2. Mark the hole locations.
3. Cut out installation template from
instructions.
4. Punch out hole locations.
5. Tape template to cabinet lining
up dotted line with top edge of
cabinet opening.
6. Close cabinet door/drawer.
7. Mark top edge of door/drawer on
the template. Also mark the width
of the template on the door/drawer.
8. Open door/drawer. Remove
template from base of cabient and
retape onto the inside of the
door/drawer.
9. Position the template onto the
inside of the door/drawer lining up
the pencil marks.
10. Mark hole locations.
11. Predrill holes with X” drill bit.
Front edge of cabinet opening
Front edge of cabinet opening
Front edge of cabinet opening
Front edge of cabinet opening
4 Haga una línea en la plantilla entre los dos bordes
marcados en la puerta/cajón del armario con las líneas
marcadas en el borde superior de la puerta/cajón del
armario y fije con cinta adhesiva (Figura 4).
5 Marque las ubicaciones de los orificios de la plantilla en
la puerta/cajón del armario. Quite la plantilla y perfore
los orificios con una broca de 1/16” (1.5 mm).
6 Fije el pestillo firmemente con tornillos.
NOTA: No se tendría que abrir la puerta/cajón del
armario más de 2” (5,08 cm).
1
1. Line up catch to the front edge of
the door/drawer opening.
2. Mark the hole locations.
3. Cut out installation template from
instructions.
4. Punch out hole locations.
5. Tape template to cabinet lining
up dotted line with top edge of
cabinet opening.
6. Close cabinet door/drawer.
7. Mark top edge of door/drawer on
the template. Also mark the width
of the template on the door/drawer.
8. Open door/drawer. Remove
template from base of cabient and
retape onto the inside of the
door/drawer.
9. Position the template onto the
inside of the door/drawer lining up
the pencil marks.
10. Mark hole locations.
11. Predrill holes with X” drill bit.
Front edge of cabinet opening
Front edge of cabinet opening
Front edge of cabinet opening
Front edge of cabinet opening
3
4
To Clean Para limpiar
Wipe clean. Keep lock dry. Limpie con un paño. Mantenga la traba seca.
To Use Para Usar
1 When drawer is opened 2” the latch
will engage catch. Press down on latch
with finger to open.
NOTE: Latch may be difficult to access
if used on a top drawer that has a
counter top with a 1” overhang. If latch
is difficult to access, insert a rounded
object to depress latch.
1 El pestillo se enganchará con la traba
cuando la puerta o gaveta se abra
5.08 cm (2 pulgadas). Para abrir la puerta
o gaveta, empuje el pestillo hacia abajo
con un dedo.
NOTA: Puede ser difícil acceder al pestillo
si lo utiliza en un cajón superior que tiene
un mostrador con un saliente de 1 pulg. Si
1"
To Install:
1. Attach enclosed positioning tape to mounting
surface of all pieces. DO NOT remove second
tape backing yet.
2. Position catch 1˝ from inside edge of cabinet
frame. Mark catch position. Remove positioning
tape backing and stick in position.
CAUTION: Enclosed double-sided tape is for
positioning only. You must secure catch and latch
to cabinets and drawers with enclosed screws.
3. Position latch so it engages catch when door is
opened about 1.5˝. Mark latch position. Remove
positioning tape backing and stick in position.
Check alignment of catch and latch prior to
attaching with screws. After checking alignment,
secure both catch and latch tightly with screws.
To Use:
When drawer is opened 1.5˝ the latch will engage
catch. Press down on latch with finger to open.
NOTE: An alternative method to mount these cabinet latches is to
mount the catch on the side of the cabinet and then mount the latch
sideways on the edge of the cabinet door or drawer.
CAUTION: This product is only a deterrent. It is not a substitute for
proper adult supervision. Discontinue use when child becomes old
enough to defeat it. Toxic and dangerous substances, as well as
sharp-edged or pointed objects, should always be placed “high up”
or made otherwise inaccessible to small children.
NOTE: Latch may be difficult to access if used on a top drawer that
has a counter top with a 1" overhang. If latch is difficult to access,
insert a rounded object to depress latch.
Cabinet & Drawer Latches
1"
To Install:
1. Attach enclosed positioning tape to mounting
surface of all pieces. DO NOT remove second
tape backing yet.
2. Position catch 1˝ from inside edge of cabinet
frame. Mark catch position. Remove positioning
tape backing and stick in position.
CAUTION: Enclosed double-sided tape is for
positioning only. You must secure catch and latch
to cabinets and drawers with enclosed screws.
3. Position latch so it engages catch when door is
opened about 1.5˝. Mark latch position. Remove
positioning tape backing and stick in position.
Check alignment of catch and latch prior to
attaching with screws. After checking alignment,
secure both catch and latch tightly with screws.
To Use:
When drawer is opened 1.5˝ the latch will engage
catch. Press down on latch with finger to open.
NOTE: An alternative method to mount these cabinet latches is to
mount the catch on the side of the cabinet and then mount the latch
sideways on the edge of the cabinet door or drawer.
CAUTION: This product is only a deterrent. It is not a substitute for
proper adult supervision. Discontinue use when child becomes old
enough to defeat it. Toxic and dangerous substances, as well as
sharp-edged or pointed objects, should always be placed “high up”
or made otherwise inaccessible to small children.
NOTE: Latch may be difficult to access if used on a top drawer that
has a counter top with a 1" overhang. If latch is difficult to access,
insert a rounded object to depress latch.
Cabinet & Drawer Latches
12
1. Line up catch to the front edge of
the door/drawer opening.
2. Mark the hole locations.
3. Cut out installation template from
instructions.
4. Punch out hole locations.
5. Tape template to cabinet lining
up dotted line with top edge of
cabinet opening.
6. Close cabinet door/drawer.
7. Mark top edge of door/drawer on
the template. Also mark the width
of the template on the door/drawer.
8. Open door/drawer. Remove
template from base of cabient and
retape onto the inside of the
door/drawer.
9. Position the template onto the
inside of the door/drawer lining up
the pencil marks.
10. Mark hole locations.
11. Predrill holes with X” drill bit.
Front edge of cabinet opening
Front edge of cabinet opening
Front edge of cabinet opening
Front edge of cabinet opening
2
Catch:
1 Line up catch to the front edge of the cabinet
opening.
2 Mark the hole locations and the outer edges of the
catch on the cabinet opening (Figure 1).
3 Predrill holes with a 1/16” (1.5mm) drill bit.
4 Secure catch tightly with screws.
Enganche:
1 Alinee el enganche hasta el borde delantero de la
abertura del armario.
2 Marque las ubicaciones de los agujeros y los bordes
exteriores del enganche en la abertura del armario
(Figura 1).
3 Perfore los orificios con una broca de 1/16” (1.5 mm).
4 Fije firmemente el enganche con los tornillos.
Latch may be difficult to access if used on a top drawer that has a
countertop with a 1” overhang. If latch is difficult to access, insert a
rounded object to depress latch.
es difícil acceder al pestillo, inserte un objeto redondo para presionarlo.
El pestillo puede ser de difícil acceso si se utiliza en un cajón superior
que tiene una encimera con un 1’’ que sobresale. Si el pestillo es de difícil
acceso, inserte un objeto redondo para apretar el pestillo.