HomeKing BYHG604.5SS User manual

1
User Manual for your
BYHG604.5SS / BYHG610.5SS
60 cm 4 Burner gas hob
BYHG710.5SS
70 cm 5 Burner gas hob
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
JW 18/05/12

2
Contents
Environmentalnote 3
Important safety information 4-6
Specifications 7-9
BYHG604.5SS 7
BYHG610.5SS 8
BYHG710.5SS 9
Electricaldetails 10
Gasdetails 10
Using the gas hob 11-13
Beforefirstuse 11
Thegashob 11
Automatic ignition with flame failure safety device 12
Energysavingtips 13
Cleaning 14-15
Cleaningthehobtop 14
Aftereachuse 14
Cleaning the hob burners 14
Maintaining the pan stands 15
Installation 19-26
Positioning 17
Unpacking the appliance 18
Installing the appliance 18
Gasconnection 20
Ventilation requirements 21
Gas Safety (Installation and Use) Regulations 22
Gas Adjustment (Conversion to LPG) 23
Minimum flow adjustment for hob gas taps 24
Gastapmaintenance 24
Electricalconnection 26
Replacing the mains supply cable 26
My appliance isn’t working correctly 27
Contactdetails 28

Environmental note
3
oThe packaging materials that the manufacturer uses are
environmentally friendly and can be recycled.
all packaging material with due regard for the
environment.
oPlease discard

4
Important safety information
Your safety is of the utmost importance to us. Please
make sure that you read this instruction booklet before
attempting to install or use the appliance. If you are
unsure of any of the information contained in this
booklet, please contact the Customer Care Department.
ehold use and for
ambient temperature of the
scolouration at
of this temperature limit, will be the liability of
uarantee. The foregoing does not affect
f the manufacturer
ld not use this appliance to store items on or as a work
ns to the appliance are permitted by the
kept away
Service Engineers that
are approved by the manufacturer
General Information
This appliance is designed for domestic housothe cooking and frying of domestic foodstuffs.
oIMPORTANT: The adjacent furniture and all materials used in
the installation must be able to withstand a minimum
temperature of 85°C above the
room it is located in, whilst in use.
oCertain types of vinyl or laminate kitchen furniture are
particularly prone to heat damage or di
temperatures below the guidelines given above.
oAny damage caused by the appliance being installed in
contravention
the owner.
oYour new appliance is guaranteed against electrical or
mechanical defects, subject to certain exclusions that are noted
in the Conditions Of G
your statutory rights.
oThe use of this appliance for any other purpose or in any other
environment without the express agreement o
will invalidate any warranty or liability claim.
oYou shou
surface.
oNo modificatio
manufacturer.
oYou should not store or place flammable or highly flammable
liquids/materials on top of or near the appliance. Items made
from aluminium, plastic or plastic film should also be
from the appliance, as they may fuse to the surface.
oRepairs may only be carried out by

5
hild Safety
at any time. During and after use, all
surfaces will be hot.
se ensure that they are kept under close supervision
at all times.
uld only be allowed to utilise the appliance
when supervised.
eneral Safety
e installed and connected by a
GASSAFE registered installer.
uild the appliance into, meet with the relevant
standards.
uring use
hob surface when it
is delivered should be removed before use.
the appliance, otherwise
there is a risk of burns being caused.
t with the hob surface when it is hot or any hot
cookware.
ng with fat and oil the appliance should
not be left unattended.
sure that all of the cooking zones are switched off after
use.
leaning
Cleaning of the hob should be carried out on a regular basis.
appliance, it
should be disconnected from the mains and cool.
C
oWe strongly recommend that babies and young children are
prevented from being near to the appliance and not allowed to
touch the appliance
oIf it is necessary for younger family members to be in the
kitchen, plea
oOlder children sho
G
oThe appliance should only b
oCare should be taken to ensure that the units and work surfaces
that you b
D
oAny film or stickers that are present on the
oCare should be taken when utilising
oYou should not allow the electrical connection cables to come
into contac
oIf fat and oil overheats, then it can ignite extremely quickly. For
this reason, when cooki
oMake
C
o
oIMPORTANT: Before attempting to clean the

6
using this appliance and when
following the cleaning procedure.
other high pressure
cleaning equipment to clean the appliance.
ion of this booklet that refers to
installation.
a result of improper
use or installation of this appliance.
ion
Vehicle, the requirements of N 721 MUST be followed.
t this
appliance is installed on any type of marine vessel.
eclaration of conformity
This appliance complies with the following European Directives:
sion
/128/EEC This appliance is suitable to come in
004/108/CE Electromagnetic compatibility
liance must be used by a
ained person for domestic purposes only.
oGreat care should be taken whilst
oYou should not use a steam jet or any
Installation
This appliance must be correctly installed by a
GASSAFE registered installer, strictly in
accordance with the manufacturer’s instructions
and the relevant British Standards. Please see the
specific sect
oThe manufacturer declines any responsibility for injury or
damage, to person or property, as
oIf the appliance is being used in a Leisure Accommodat
oThe manufacturer DOES NOT recommend tha
D
-2006/95/CE General regulations / Low ten
-2009/142/CE Concerning gas appliances
-1935/2004/CE 90
contact with food
-2
The manufacturer declares that the hob is built using certified
materials and requires the appliance to be installed in accordance with
the standards currently in force. This app
tr

7
pecifications – BYHG604.5SS/WS
Product dimens ons:
i
idth: 560 mm
rs
rner
ty device on each burner
as hob surface layout
= 1.00 kW auxiliary burner
Aperture dimensions:
Depth: 510 mm
Width: 620 mm D W
epth: 480 mm
Height: 50 mm
Product specifications:
o1 x 3.00 kW rapid burner
o2 x 1.75 kW semi-rapid burne
o1 x 1.00 kW auxiliary bu
oFront control operation
oEnamelled pan stands
oAutomatic ignition
oFlame failure safe
Standard accessories:
oLPG conversion jets
G
1 = 1.75 kW semi-rapid burner
2 = 1.75 kW semi-rapid burner
= 3.00 kW rapid burner3
4

8
pecifications – BYHG610.5SSS
Product dimensions: Aperture dimensions:
Depth: 510 mm
Width: 620 mm Depth: 480 mm W
Height: 50 mm idth: 560 mm
urner
r
3 = 1.00 kW auxiliary burner
Product specifications:
o2 x 1.75 kW semi-rapid burner
1 x 1.00 kW auxiliary burnero
o1 x 3.50 kW triple crown (wok) b
Front control operationo
oHeavy duty cast iron pan stands
oAutomatic ignition
oFlame failure safety device on each burner
Standard accessories:
oLPG conversion jets
Gas hob surface layout
1 = 3.50 kW triple crown burner
2 = 1.75 kW semi-rapid burner
2 = 1.75 kW semi-rapid burne

Specifications – BYHG710.5SS
Product dimensions:
Aperture dimensions:
Depth: 510 mm
Width: 720 mm
Height: 50 mm
Depth: 480 mm
Width: 560 mm
Product specifications:
o1 x 3.00 kW rapid burner
o2 x 1.75 kW semi-rapid burners
o1 x 1.00 kW auxiliary burner
o1 x 3.50 kW triple crown (wok) burner
oFront control operation
oHeavy duty cast iron pan stands
oAutomatic ignition
oFlame failure safety device on each burner
Standard accessories:
oLPG conversion jets
Gas hob surface layout
1 = 1.75 kW semi-rapid burner
2 = 1.75 kW semi-rapid burner
3 = 3.50 kW triple crown burner
4 = 3.00 kW rapid burner
5 = 1.00 kW auxiliary burner
9

10
Electrical details
Rated Voltage: 230 Vac 50 Hz
Supply Connection: 3A (double pole switched fused outlet with
3mm contact gap)
Mains Supply Lead: 3 core x 1.5 mm²
Gas details
Connection: Rp ½ (ISO R7)
Type: Natural Gas (20 mbar)
Alternative LPG G30 (28-30/37 mbar)
For future reference please record the following information which can
be found on the rating plate and the date of purchase which can be
found on your sales invoice. The rating plate of your hob is located on
the underneath of the appliance. Therefore it is a good idea to record
this information before you install your appliance.
Model Number ……………………………….
Serial Number ……………………………….
Date of Purchase ……………………………….

Using the gas hob
Before first use
IMPORTANT: You should clean the hob surface
(see “Cleaning and maintenance” section).
The gas hob
The following symbols will appear on the control panel, next to each
control knob:
Circle: gas off
Large flame: maximum setting / ignition position
Small flame: minimum setting
oThe minimum setting is at the end of the anti-clockwise rotation
of the control knob.
oAll operation positions must be selected between the maximum
and minimum position.
oNever select a knob position between the maximum and off
position.
oThe symbol on the control panel, next to the control knob will
indicate which gas burner it operates.
11

12
Automatic ignition with flame failure safety device
The appliance is fitted with a flame failure safety device on each
burner, which is designed to stop the flow of gas to the burner head in
the event of the flame going out.
To ignite a burner:
oPress in the control knob of the burner that you wish to light and
turn it anti-clockwise to the maximum position.
oIf you keep the control knob depressed, the automatic ignition
for the burner will operate.
oYou should hold down the control knob for 20 seconds after the
flame on the burner has lit.
oAfter this 20 second interval, to regulate the flame you should
continue turning the control knob anti-clockwise until the flame
is at a suitable level. The operating position MUST be at a
position between the maximum and minimum position.
oTo switch the burner off, turn the control knob fully clockwise to
the gas off position.
oIn case of power failure, the burners can be lit by carefully using
a match.

Energy saving tips
Pan sizeBurners Ø min Ø max
Wok 200 mm 320 mm
Rapid 200 mm 260 mm
Semi-rapid 140 mm 200 mm
Auxiliary 100 mm 140 mm
oThe diameter of the bottom of the pan should correspond to that
of the burner.
oThe burner flame must never extend beyond the diameter of the
pan.
oUse flat bottomed pans only.
oWhen possible, keep a lid on the pan whilst cooking.
oCook vegetables with as little water as possible, to reduce
cooking times.
IMPORTANT: Always place pans centrally over the hob burners and
position them so that the handles cannot get accidentally caught or
knocked off. You should also make sure that the handle is not over one
of the other hob burner flames.
13

Cleaning
Cleaning operations must only be carried out when
the hob is cool.
The appliance should be disconnected from your
mains supply before commencing any cleaning
process.
Cleaning the hob top
Any residues that are left on the hob top surface from cleaning
agents will damage it. You should remove any residues with
warm soapy water.
Abrasive cleaners or sharp objects will damage the hob surface;
you should clean it using warm soapy water.
Although it is easier to clean some deposits whilst the
hob surface is still warm, make sure that the hob surface,
pan supports and hob burners have all cooled sufficiently
before you attempt to touch them.
After each use
oRemove the pan stands and wipe the appliance over with a soft,
damp cloth that has been put into warm soapy water. The cloth
should be wrung out after being taken out of the soapy water.
oDry the appliance by rubbing the surface with a soft, clean cloth.
oWe would recommend that an appropriate stainless steel cleaner
and polish is regularly used on the stainless steel surfaces of this
appliance.
Cleaning the hob burners
The hob burners should be cleaned once a week or more frequently if
they get soiled.
oIMPORTANT: Make sure that the hob surface, pan stands and
hob burners have cooled before you attempt to touch them.
oRemove the hob burners by pulling them upwards and away
from the hob top.
oSoak them for about ten minutes in hot water and a little
detergent.
14

15
oAfter cleaning and washing them, wipe and dry them carefully.
oBefore placing the burners back on the hob top, make sure that
the gas jet is not blocked.
oIMPORTANT: Make sure that you reassemble the burners in the
original way.
Maintaining the enamelled pan stands
(BYHG604.5SS)
oIMPORTANT: Make sure that the hob surface and pan stands
have cooled before you attempt to touch them.
oWipe the pan stands over with a soft, damp cloth that has been
put into warm soapy water. The cloth should be wrung out after
being taken out of the soapy water.
oUsing a paper towel, thoroughly dry the pan stands.
Maintaining the cast iron pan stands
(BYHG610.5SS / BYHG710.5SS)
oIMPORTANT: Make sure that the hob surface and pan stands
have cooled before you attempt to touch them.
oWipe the pan stands over with a soft, damp cloth that has been
put into warm soapy water. The cloth should be wrung out after
being taken out of the soapy water.
oUsing a paper towel, thoroughly dry the pan stands.
oTo maintain the appearance of the cast iron pan stands, we
would recommend that you rub a small amount of olive oil into
the pan stands, after you have finished cleaning them.

Installation
The installation must be carried out by a GASSAFE
registered installer, in accordance with the current
version of the following.
oGas Safety Regulations (Installation & Use)
oBuilding Regulations (issued by the Department of Environment)
oBuilding Standards (Issued by the Scottish Development
Department)
oIEE Wiring Regulations
oElectricity at Work Regulations BS 6172
oInstallation of Domestic Gas Cooking Appliances (if necessary,
BS 5482 Installation of Domestic LPG Appliances)
oBS 5440 Installation of Flues and Ventilation for Gas Appliances
oManufacturer’s installation Instructions
16

Positioning
The adjacent furniture must be able to withstand a
minimum temperature rise of 85°C above the ambient
temperature of the room it is located in, during
periods of use.
oThis appliance can be located in a kitchen, a kitchen diner or a
sitting room. IMPORTANT: The appliance must not be installed
in a bathroom or shower room.
This appliance is classified as Class 3 and therefore is to be built into a
kitchen unit (depending on size) or 600 mm worktop that is between
25 mm and 40 mm thick. The following minimum clearance distances
must be observed:-
o700 mm between the hob surface and the underside of any
horizontal surface above it.
o50 mm clearance around the front, back and sides of the
appliance, measured from the cut out.
oThe wall MUST be made of a non-combustible material.
oIf the hob is positioned so that the right or left hand side of the
appliance will be near to the edge of a kitchen unit. There must
be a gap of at least 150 mm between the side of the hob and the
vertical surface of any kitchen unit that is made of a combustible
material. If the vertical surface is made of a non-combustible
material, then 55 mm clearance is sufficient. HOWEVER
sufficient space must be allowed for saucepan handles to be
turned and for saucepans to be used safely.
17

Unpacking the appliance
When unpacking the appliance please check that the following items
are contained within the packaging:
1 x Hob
Pan stands
Burner assemblies
Instruction manual
Warranty card
Fixing screws
Clamps
Sealing strip
LPG conversion jets
Self-adhesive label for amending the gas category on the appliance’s
rating plate (required if the LPG conversion jets are used).
Installing the appliance
oCut a hole in the worktop that corresponds with the correct
model drawing below:
BYHG604.5SS
BYHG610.5SS
BYHG710.5SS
18

oCarefully turn the hob upside down and place it on a cushioned
mat.
oApply the sealing strip provided around the edge of the
appliance.
oThe protective covering must be removed from both sides.
oDo not leave a gap in the sealing agent or overlap the thickness.
oIMPORTANT: Do not use a silicon sealant to seal the appliance
against the aperture. This will make it difficult to remove the hob
from the aperture in future, particularly if it needs to be
serviced.
(A) Sealing strip
(B) Clamp
(C) Screw
oPlace the clamp (B) over the holes that match the size of the
screws. There are one set of screw holes in each corner of the
hob. Slightly tighten a screw (C) through the clamp (B) so that
the clamp is attached to the hob, but so that you can still adjust
the position of it.
oCarefully turn the hob back over and then gently lower it into the
aperture hole that you have cut out.
19

oOn the underneath of the hob, adjust the clamps into a position
that is suitable for your worktop. Then fully tighten the screws
(C) to secure the hob into position.
Gas connection
20
nts.
This appliance must be installed by a competent
person in accordance with the current versions of
the following UK (United Kingdom) or ROI (Republic
of Ireland) Regulations and Safety Standards or
their European Norm Replaceme
Important information
oThis hob is supplied to run on natural gas only and cannot be
used on any other type of gas without modification.
oConversion for use on LPG and other gases must only be
undertaken by a qualified person. For information on the use of
other gases, please contact the Customer Care Department.
oThe hob must be installed by a qualified person, in accordance
with the current edition of the Gas Safety (Installation and Use)
(Amendment) Regulations and the relevant building/I.E.E.
Regulations.
oFailure to install the appliance correctly could invalidate the
manufacturer's guarantee and lead to prosecution under the
regulations quoted above.
oIn the UK, GASSAFE registered installers are authorised to
undertake the installation and service work, in compliance with
the above regulations.