Honeywell UV100E1043 User manual

INSTALLATION INSTRUCTIONS
69-1444-5
UC100 Ultraviolet System
Replacement Bulb/Handle Assembly
APPLICATION
The UC100 Ultraviolet System Replacement Bulb/Handle
Assembly is for use with the UV100 Ultraviolet System. See
Table 1 for your model.
INSTALLATION
When Installing this Product…
1. Read these instructions carefully. Failure to follow them
could damage the product or cause a hazardous
condition.
2. Check the rating given in the instructions and on the
product to make sure the product is suitable for your
application.
3. Removal and replacement of the ultraviolet lamps can
easily be done by the homeowner following these
instructions. The homeowner can also call an
experienced service technician.
4. After installation is complete, check out product
operation as provided in these instructions.
CAUTION
Personal Injury Hazard.
Power supply can cause electrical shock.
Disconnect power supply before replacing ultraviolet
bulb(s).
Do not open base unit or lamp handle; there are no
user-serviceable components inside.
WARNING
UV Light Hazard.
Harmful to bare skin and eyes.
Can cause temporary or permanent loss of vision.
Never look at bulbs while illuminated.
View illumination only through light indicator located
on lamp handle.
To prevent exposure to ultraviolet light, disconnect
power to Ultraviolet System before servicing any part
of heating and air conditioning system.
CAUTION
UV Lamp Burn Hazard.
Harmful to bare skin.
Can cause severe burns.
Disconnect power and wait 15 minutes before
removing ultraviolet bulb(s).
CAUTION
Breakable Glass Hazard.
Can cause personal injury.
Be careful when inserting bulb(s) into lamp base.
Wear protective gloves when handling bulb(s).

UC100 ULTRAVIOLET SYSTEM REPLACEMENT BULB/HANDLE ASSEMBLY
69-1444—5 2
MERCURY NOTICE
This device contains mercury in the sealed ultraviolet
bulb(s). Do not place your used bulb(s) in the trash.
Dispose of properly.
Broken Bulb Cleanup.
Do not use a household vacuum.
Sweep debris (phosphor/glass) into a plastic bag and
dispose of properly.
Contact your local waste management authority for
instructions regarding recycling and the proper
disposal of old bulb(s).
Replacing Your Bulbs
SmartLamp™ Models (UV100E1043, UV100E2009,
and UV100E3007)
Replacement of your bulbs is required when LED on front of
unit is lighted solidly.
NOTE: LED blinking slowly, one second on and one second
off, indicates that ten percent or less of bulb life
remains and homeowner must order new bulb(s).
IMPORTANT
Remember to press the reset button for five seconds
after replacing the bulb(s).
UV100A1000, UV100A1018, UV100A1026,
UV100A1059, UV100A2008, UV100E1001,
UV100E1019, UV100E1027, UV100E1035 Models
Annual replacement of your bulbs is required.
To replace your bulbs:
1. Select and obtain the correct replacement bulb for your
unit. See Table 1.
2. Disconnect the power to your heating and cooling
system.
3. Unplug or turn off power to your UV System and allow
the bulbs to cool for at least 15 minutes.
4. Rotate the lamp handle counterclockwise and gently
pull the lamp handle to remove the bulb. See Fig. 1.
IMPORTANT
If the bulb in your model has external wires running
along the glass surface, be sure to avoid pulling on
those wires.
Fig. 1. Remove lamp bulb.
5. If you have a SnapLamp™ handle, follow steps 5 and 6;
otherwise, proceed to step 7. Grasp the SnapLamp™
handle in one hand and the bulb glass in the other and
pull straight apart. See Fig. 2.
Fig. 2. Disconnect bulb from SnapLamp™ handle.
6. Insert the new bulb into the SnapLamp™ handle by
aligning the notch and pushing straight together.
See Fig. 3.
Fig. 3. Replace bulb in SnapLamp™ handle.
7. Insert the lamp handle into the base with the lamp light
indicator at the eleven o’clock position. Continue
pushing and gently rotating counterclockwise until the
lamp inserts fully into the base. See Fig. 4.
M22841
M22851
M22853

UC100 ULTRAVIOLET SYSTEM REPLACEMENT BULB/HANDLE ASSEMBLY
369-1444—5
Fig. 4. Position lamp handle for insertion back into
the lamp base.
8. Rotate the lamp handle clockwise until it snaps into
place with the light indicator aligned with the raised
button on the unit cover. See Fig. 5.
Fig. 5. Snap lamp handle into place.
9. Reconnect power to your UV System.
10. For UV Air Treatment System SmartLamp™ models,
wait ten minutes for the airflow sensor to calibrate.
During this time, the furnace fan must remain off.
NOTE: Failure to wait ten minutes for the airflow sensor to
calibrate before powering the system fan causes the
airflow sensor to incorrectly calibrate and the device
to incorrectly function. If this occurs, remove power
to the furnace or turn off the system fan, wait ten
minutes, and then resume normal fan operation.
WARNING
UV Light Hazard.
Harmful to bare skin and eyes.
Can cause temporary or permanent loss of vision.
Never look at bulbs while illuminated.
View illumination only through light indicator located
on lamp handle.
To prevent exposure to ultraviolet light, disconnect
power to Ultraviolet System before servicing any part
of heating and air conditioning system.
11. Verify that your ultraviolet bulbs are operating by
viewing only through the lamp light indicator on the lamp
handle. Never look directly at your lamp while it is
illuminated.
12. Reconnect the power to your heating and cooling
system.
13. For SmartLamp™ models, press and hold the reset
button for five seconds to reset the internal timers.
M22847
M22849
Table 1. Replacing Your Bulb(s) and Handle Assembly.
Unit Description
Replacement Bulb/
Handle Assembly
SnapLamp™
Replacement Bulb Wattage
UV100E1001 and UV100E1043
Air Treatment Systems
UC100E1006 UC18W 18W
UV100E1019 and UV100E2009
Air Treatment Systems (dual lamp)
UC100E1030 (2 needed) UC36W (two bulbs required) 36W
UV100E1027 Surface Treatment System UV100A1021 N/A 25W
UV100E1035 and UV100E3007
Surface Treatment Systems
UC100E1030 UC36W 36W
UV100A1000 Air Treatment System UC100A1005 UC18W 18W
UV100A1018 Air Treatment System (dual lamp) UC100A1054 (2 needed) UC36W (two bulbs required) 36W
UV100A1026 Surface Treatment System UC100A1021 N/A 25W
UV100A1059 Surface Treatment System UC100A1054 UC36W 36W
UV100A2008 Surface Treatment System UC100A1054 UC36W 36W

UC100 ULTRAVIOLET SYSTEM REPLACEMENT BULB/HANDLE ASSEMBLY
Automation and Control Solutions
Honeywell International Inc. Honeywell Limited-Honeywell Limitée
1985 Douglas Drive North 35 Dynamic Drive
Golden Valley, MN 55422 Toronto, Ontario M1V 4Z9
customer.honeywell.com
® U.S. Registered Trademark
© 2006 Honeywell International Inc.
69-1444—5 M.S. Rev. 10-06