Honeywell NPB-ZWAVE User manual

INSTALLATION INSTRUCTIONS
Put Bar Code Here
62-0349-01
NPB-ZWAVE Option Card
This document covers the mounting of a NPB-ZWAVE option
card in a Tridium® JACE®controller, including models WEB/
CP-600, WEB/CP/700, WEB/CP/602-XPR, or WEB/CP
controllers.
NOTE: The WEB/CP Controller requires NiagaraAX-3.5 or
later to support operation of the
NPB-ZWAVE .
Not covered in this document are NiagaraAX Z-Wave driver
(software) topics about using this option card. For all other
related mounting and wiring details, refer to the appropriate
mounting and wiring document. See “Related
Documentation”.
INCLUDED IN THIS PACKAGE
Included in this package you should find the following items:
• NPB-ZWAVE option card, with pre-attached endplate.
• an RP-SMA coax-mounted stub antenna.
• This document NPB-ZWAVE Option Card Installation
Instructions, Form Number 69-0349.
Fig. 1. NPB-ZWAVE Option
MATERIAL AND TOOLS
REQUIRED
The following supplies and tools are required:
• #2 phillips screwdriver: used to install the NPB-ZWAVE
option card.
• If installing in a
WEB/CP-XPR (WEB/CP-202/602-XPR), an
antenna cable kit. See
“Antenna Extension Option” . Also, a
#1 phillips screwdriver.
Table 1. NPB-ZWAVE option description.
Description Models /Notes
Z-Wave wireless option
card for serial gateway
support between the
hosted WEBStation-AX
or Comfort Point
Workbench and an RF
wireless Z-Wave domain.
This option card allows
NiagaraAX integration of
wireless Z-Wave
devices.
An RP-SMA coax stub
antenna is included.
Four status LEDs are on
the option card’s top
surface.
NPB-ZWAVE - For domestic
U.S. usage.
908.42 MHz frequency
An optional antenna extension
kit allows the included antenna
to be located up to 6.56 feet
(2m) away from the option
card.
This kit is required if installing
in a WEB/CP-202-602
controller model. See “Antenna
Extension Option”.
The NPB-ZWAVE option card
adds one COM port on the
JACE controller. See “COM
Port Usage”.
TX
RX
SERIAL
LED1
LED2
M32453
STATUS LEDS STATUS LEDS
ANTENNA
CONNECTOR
RP-SMA COAX
SUPPLIED
STUB
ANTENNA

NPB-ZWAVE OPTION CARD
62-0349-01 2
MOUNTING
WARNING
Power to the controller must be OFF when
installing or removing option cards, or damage
will occur! Also, you must be very careful to plug
any option card into its connector properly (pins
aligned).
Mount the NPB-ZWAVE option card in either of the option
card slots of the controller, as needed. Note the WEB/CP-202/
602-XPR series has only one option card slot.
Mounting NPB-ZWAVE option card.
1. Remove power from the WEB/CP Controller—see
the previous Warning.
2. Remove the JACE cover or covers (WEB/CP-202/
602-XPR).
For all but the WEB/CP-202/602-XPR, press in the
four tabs on both ends of the unit, and lift the cover
off.If a WEB/CP-202/602-XPR, first remove the right
cover, then the left cover, retaining the two screws that
secure each cover.
NOTE: If accessory modules are plugged into the controller,
you may need to slide them away from the unit to get
to the cover tabs.
3. If a WEB/CP-202/602-XPR series, remove the bat-
tery and bracket assembly by taking out the
screws holding it in place, setting screws aside for
later.
Figure 2 shows an exploded view of a WEB/CP-600.
Fig. 2. Remove screws and battery assembly
NOTE: The tie wrap on the battery pack should have its lock
“knot” on top, as shown in Figure 2.
If not, cut and remove the tie, then re-install another
tie wrap with its lock tab on top.
(Tie lock at bottom interferes with option card).
4. If a WEB/CP-201/600-XPR or WEB/CP-700,
remove the option slot blanking plate, retaining the
two screws.
NOTE: Slot 2 option card installation in a WEB/CP-700
controller requires careful attention! See its Mounting
and Wiring Guide for more details. This document
focuses on installation in a WEB/CP-201/600 series
controller.
5. Remove the blanking end plate for the slot you are
installing the option card into.
(Retain the blanking end plate in case the option card
must be removed at a later date.)
M32454
SCREWS (4)
UNPLUG BATTERY HERE
OPTION SLOT 2 AREA
WEB/CP-600
OPTION SLOT 1 AREA
BLANKING END PLATE
TIE WRAP
LOCK
(SEE NOTE)
BATTERY ASSEMBLY
(INCLUDES
CABLE AND
BRACKET)

NPB-ZWAVE OPTION CARD
362-0349-01
6. Carefully insert the pins of the NPB-ZWAVE into the
socket of the appropriate option card slot. Mounting
holes on the option board should line up with the stand-
offs on the base board. If they do not, the connector is
not properly aligned. Press until the option card is com-
pletely seated.
Figure 3 shows a card going into Slot 2 of WEB/CP-201/600
series controller.
Fig. 3. Option card going into Slot 2
7. If a WEB/CP-201/600 series, set the battery and
bracket assembly back over the option card slots, with
the mounting holes aligned with the standoffs.
8. Place the four screws through the battery bracket, end
plates, and into the standoffs on the controller base
board. Hand tighten these screws.
Fig. 4. Re-fasten screws through battery bracket
9. Plug the battery cable into the battery connector on the
controller see Figure 4.
10. Replace the controller’s cover.
If accessory modules were unplugged, plug them back
into the controller as before, and secure.
ATTACHING ANTENNA
Astub antenna with RP-SMA coax connector is provided for
use with a WEB/CP-201/600 or WEB/CP-700 controller. To
attach, simply insert into the coax jack on the option card, and
finger-tighten the knurled nut (See Figure 5).
Fig. 5. RP-SMA stub antenna on WEB/CP-201/600
Rotate in whatever position is needed for mounting clearance
and/or best reception. If needed, you can use the antenna
extension option.
ANTENNA EXTENSION OPTION
To locate the included stub antenna off the controller, or if
installing in a WEB/CP-202/602-XPR model, order and install
the H-CBL-SED-EXT option. Included is a 6.56 ft. (2m)
RP-SMA-type coax extension cable and steel bracket for wall
or panel mounting. See Figure 6 for details and dimensions.
Fig. 6. Dimensions in in. (mm)
M32455
INSERT OPTION CARD
INTO OPTION CARD
SLOT CAREFULLY,
WITH PINS ALIGNED.
FULLY SEATED CARD
M32456
HAND TIGHTEN 4 SCREWS
THROUGH BATTERY BRACKET, END
PLATES, INTO STANDOFFS.
CONTROLLER
BATTERY
CONNECTOR
M32457
STUB ANTENNA
INSTALLED ON
NPB-ZWAVE
OPTION CARD
.236
(6)
(15.9)
.625 .251
1.25
(6.37)
2.0
(50.8)
(31.8)
1.13
(28.7)
.625
(15.9)
STUB ANTENNA
BRACKET
RP-SMA
TYPE COAX
EXTENSION
CABLE
MOUNTING HOLES (2)
.170
(4.32)
1
(25.4)
M32458

NPB-ZWAVE OPTION CARD
Automation and Control Solutions
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
Honeywell Limited-Honeywell Limitée
35 Dynamic Drive
Toronto, Ontario M1V 4Z9
customer.honeywell.com
® U.S. Registered Trademark
© 2011 Honeywell International Inc.
62-0349—01 T.W. Rev. 01-11
Printed in U.S.A.
Some installations may require a different external antenna.
NOTE: Any external antenna must be compatible with the Z-
Wave frequency (U.S. 908.42 MHz) and the 50 Ω
impedance of the RP-SMA coax connector on the
NPB-ZWAVE option card.
LEDS
Four (4) LEDs are on the top of the option card—you must
remove the controller cover to see them. See Figure 1.
Two LEDs indicate serial communications activity (“RX”, “TX”)
to/from the controller. The other two LEDs are controlled by
the option card’s PLD (Programmable Logic Device), where
functionality is programmable.
COM PORT USAGE
The NPB-ZWAVE option card has an onboard UART and so
adds one COM port on the installed JACE controller. The
hosted station automatically resolves the option’s COM
address.
•Ifa
WEB/CP-201/600 controller and installing in option Slot
1, or if the only option card, it is seen as COM3.
•Ifa controller and installing in option Slot 1, or if the only
option card, it is seen as COM5.
If installed in Slot 1 of a controller along with another option
card that uses COM ports in option Slot 2, note that COM
assignments for that other card are affected.
For example, if a NPB-ZWAVE card is in Slot 1 of WEB/CP-
201/600
and a NPB-2X-RS485 option card is in Slot 2, the two
NPB-2X-RS485 option ports are COM4 and COM5. The same
option card mix in a controller would yield Slot 2 NPB-2X-RS485
option ports of COM6 and COM7.
The NPB-ZWAVE installed in the only (single) option slot of a
T-202/602-XPR series controller is seen as COM7.
RELATED DOCUMENTATION
For more information on mounting and wiring any controller,
refer to its model-specific Mounting and Wiring Guide.
Also see the following software document:
• NiagaraAX Z-Wave Driver Guide
OPTIONS AND PARTS
The following options or replacement parts may be ordered for
the NPB-ZWAVE option card:
APPROVALS
FCC: The Panasonic module used on the NPB-ZWAVE option
card is FCC approved, and has an FCC ID of T7VPAN8550.
The module also complies to EN300220 for ETSI (European
FCC) approval.
Table 2. Parts for NPB-ZWAVE option card.
Option/Part Description
H-CBL-SED-EXT 6.56 ft (2m) RP-SMA-type coax
extension cable, and mounting bracket.
See “Antenna Extension Option”.
Required if installing the option card in a
WEB/CP-202/602-XPR model.
H11686 NPB-ZWAVE replacement RP-SMA
coax-mounted antenna (915aMHz)
aAntennas have a 30 MHz bandwidth, and the specified
center frequency does not have to align exactly with the
Z-Wave module’s frequency. Thus, the 915 MHz antenna
(H11686) is compatible with the U.S. option card’s 908.42
MHz frequency.
Niagara Framework, Niagara AX Framework and the Sedona Framework are trademarks of Tridium, Inc.