Honeywell OnCell 3150A-LTE-EU User manual

➔
www.docuthek.com
D GB F NL I E Cert. version 09.18 · Edition 09.18 ·
Please read and keep in a safe place
Please read through these instructions
carefully before installing or operating. Following the
installation, pass the instructions on to the opera-
tor. This unit must be installed and commissioned
in accordance with the regulations and standards
in force. These instructions can also be found at
www.docuthek.com.
Explanation of symbols
• ,  ,  ,  ... = Action
▷= Instruction
Liability
We will not be held liable for damage resulting from
non-observance of the instructions and non-com-
pliant use.
Safety instructions
Information that is relevant for safety is indicated in
the instructions as follows:
DANGER
Indicates potentially fatal situations.
WARNING
Indicates possible danger to life and limb.
CAUTION
Indicates possible material damage.
All interventions may only be carried out by qualified
gas technicians. Electrical interventions may only be
carried out by qualified electricians.
Conversion, spare parts
All technical changes are prohibited. Only use OEM
spare parts.
D
GB
F
NL
I
E
1
32-00191-01
QUICK START GUIDE
Industrial Cellular Router
OnCell 50A-LTE-EU
Safety
Contents
Safety ................................. 1
Checking the usage ......................2
Configuration............................2
Installation ..............................3
Wiring .................................4
Specifications ........................... 7
Standards and Certifications ................8
Warranty ...............................8
32-00191-01

2
D
GB
F
NL
I
E
OnCell G3150A-LTE-EU · Edition 09.18 · GB
Checking the usage
The OnCell G3150A-LTE is a reliable, secure, LTE
gateway with state-of-the-art global LTE module. This
4G cellular gateway provides a more reliable connec-
tion to your Ethernet network for cellular applications.
To enhance industrial reliability, the OnCell G3150A-
LTE features isolated power inputs, which together
with high-level EMS and wide-temperature support
give the OnCell G3150A-LTE the highest level of de-
vice stability for any rugged environment. In addition,
with dual-SIM GuaranLink and dual power inputs, the
OnCell G3150A-LTE supports network redundancy
to ensure uninterrupted connectivity.
The OnCell G3150A-LTE also comes with a 3-in-1
serial port for serial over LTE cellular network com-
munication. Use the OnCell G3150A-LTE to collect
data and exchange data with serial/Ethernet devices.
Package Checklist
Moxa’s OnCell G3150A-LTE is shipped with the fol-
lowing items:
– 1 OnCell G3150A-LTE unit
– 2 2G/3G/4G antennas 2 dBi omni-directional with
SMA male connectors
– 1 DIN-rail mounting kit (mounted on OnCell)
– Quick installation guide (printed)
– Warranty card
▷ If any of these items is missing or damaged,
please contact your customer service repre-
sentative for assistance.
Panel Layout
1
2
3
4
4
8
10
11
7
5
6
9
GPS/GLONASS
SIM1 SIM2
RESET
Top Panel View
Front Panel View
Rear Panel View
Bottom Panel View
1
2
3
4
4
8
10
11
7
5
6
9
GPS/GLONASS
SIM1 SIM2
RESET
Top Panel View
Front Panel View
Rear Panel View
Bottom Panel View
1
2
3
4
4
8
10
11
7
5
6
9
GPS/GLONASS
SIM1 SIM2
RESET
Top Panel View
Front Panel View
Rear Panel View
Bottom Panel View
GPS antenna connector (female SMA)
Terminal block (top-down: PWR1 and PWR2,
1 digital relay and 2 digital inputs)
Grounding screw (M5)
42x2 MIMO antenna ports for LTE (female
SMA)
5RS-232 serial console (RJ45)
610/100 Base T(X) Ethernet port (RJ45)
7LED display
8DIN-rail mounting kit
9Reset button
0 Dual SIM–SIM1
 Dual SIM–SIM2
Configuration
▷ Before configurating the OnCell G3150A-LTE,
make sure that all items in the package checklist
are in the box.
▷In addition, you will need access to a notebook
computer or PC equipped with an Ethernet port.
▷ The OnCell G3150A-LTE has a default IP address
that you must use when connecting to the device
for the first time.
Take the following steps to configure your OnCell
G3150A-LTE. For the location of the ports and sock-
ets, see page 2 (Checking the usage).
Step : Insert a SIM card and turn on the
OnCell G50A-LTE
 Use a screwdriver to loosen the screws and
remove the SIM card cover.
 Insert one or two 2G/3G/4G SIM cards (full-sized
SIM/1FF) into the SIM card slots located on the
bottom of the OnCell G3150A-LTE.
▷
If you are only using one SIM card, insert it in
the top slot (slot 1; the card in slot 1 is referred
to as SIM1).
▷By default, the SIM card in the slot 1 is treated
as the primary card. To change the default to
SIM2 (the card in slot 2), log in to the OnCell’s
web UI, and configure SIM2 as the primary card.
When the OnCell device is turned on, it boots up
based on the configuration information stored
on the primary SIM card.
 Turn on the OnCell G3150A-LTE by connecting
a power terminal block to a DC power source
(12 to 48 VDC).
▷For details, see page 4 (Wiring).
4 Reattach the cover.
Step : Connect the OnCell G50A-LTE to a
notebook or PC
▷
Since the OnCell G3150A-LTE supports MDI/
MDI-X auto-sensing, you can use either a
straight-through cable or crossover cable to
connect the OnCell G3150A-LTE to a computer.
▷See the 10/100BaseT(X) Ethernet Port Connec-
tion section below for detailed instructions.

3
D
GB
F
NL
I
E
OnCell G3150A-LTE-EU · Edition 09.18 · GB
▷ If the LED indicator on the OnCell G3150A-LTE’s
LAN port lights up, it means a connection has
been established.
Step : Set up an IP address for the computer
4 Set an IP address on the same subnet as the
OnCell G3150A-LTE.
▷ Since the OnCell G3150A-LTE’s default IP ad-
dress is 192.168.127.254, and the subnet mask
is 255.255.255.0, you should set the IP address
of the computer to 192.168.127.xxx and subnet
mask to 255.255.255.0.
Step 4: Use the web-based manager to
configure the OnCell G50A-LTE
5 Open your computer’s web browser and type
http://192.168.127.254 in the address field to
access the homepage of the web-based man-
agement system.
▷
Before the homepage opens, you will need to
enter the username and password.
6 For first-time configuration, enter the default
username and password given below:
Username: admin
Password: moxa
7 Click on the Login button.
ATTENTION
For security reasons, we strongly recommend
changing the password. To change the password,
select Maintenance ➜Username/Password, and
then follow the on-screen instructions.
▷You must either click the Save Configuration or
the Restart button for the configuration changes
to take effect.
Installation
WARNING
– This equipment is intended to be used in a Re-
stricted Access Location, such as a dedicated
computer room, where access can only be gained
by SERVICE PERSONS or by USERS who have
been instructed about the fact that the metal
chassis of the equipment is extremely hot and
may cause burns.
– Service persons or users should pay special atten-
tion and take special precautions before handling
this equipment.
– Only authorized, well-trained professionals should
be allowed to access the restricted access loca-
tion. Access should be controlled by the authority
responsible for the location with lock and key or
a security identity system.
– External metal parts are hot!! Pay special at-
tention or use special protection before handling
this equipment.
ATTENTION
– The OnCell G3150A-LTE is NOT a portable mobile
device and should be located at least 20 cm away
from the human body.
– The OnCell G3150A-LTE is NOT designed for
the general public. A well-trained technician is
required to deploy the OnCell G3150A-LTE units
and safely establish a wireless network.
– For EXPLOSION-PROOF applications, the OnCell
G3150A-LTE is designed and certified to meet
ATEX and IECEx requirements. You should mount
the device in a suitable enclosure rated at least
IP54, in accordance with IEC/EN 60079-15 stand -
ard, so that it is accessible only by the use of a
tool. The device is not intended for use in an area
with pollution degree rating > 2 in accordance
with EN 60664-1.
– When you install the OnCell G3150A-LTE in an
enclosure, the antennas must also be installed
in such a way that they are inside the enclosure.
External antenna deployment is allowed only if
the antennas are certified for ATEX Zone 2 use
or confirm to IECEx standards.
DIN-Rail Mounting
▷DIN-Rail Kit Dimensions:
Unit = mm (inch)
48.4
(1.91)
15.0
(0.59)
22.7
(0.89)
12.5 (0.49)
25.0 (0.98)
▷The OnCell G3150A-LTE comes with a DIN-rail
kit attached to the back panel.
▷ Mount the OnCell G3150A-LTE on corrosion-free
mounting rails that meet the EN 60715 standard.
 Insert the upper lip of the DIN rail into the top
hook of the DIN-rail mounting kit :
2
1
2
1

4
D
GB
F
NL
I
E
OnCell G3150A-LTE-EU · Edition 09.18 · GB
 Press the OnCell G3150A-LTE towards the DIN
rail until it snaps into place:
2
1
2
1
▷ To remove the OnCell G3150A-LTE from the DIN
rail, reverse steps and above.
Wall Mounting (optional)
▷Wall-Mounting Kit Dimensions:
Unit = mm (inch)
67.0 (2.64)
36.0 (1.42)
20.0
(0.79)
6.0 (0.24)
10.0
(0.39) 20.0
(0.79)
8.0
(0.32)
▷For some applications, it may be more conveni-
ent to mount the OnCell G3150A-LTE to a wall:
 Remove the aluminum DIN-rail attachment plate
from the OnCell G3150A-LTE
 Then attach the wall-mounting plates with M3
screws.
▷Mounting the OnCell G3150A-LTE to a wall re-
quires 4 screws.
 Use the OnCell G3150A-LTE device, with wall
mount plates attached as a guide, to mark the
correct locations of the 4 screws.
▷ The heads of the screws should be less than 6.0
mm in diameter, and the shafts should be less
than 3.5 mm in diameter.
< 6 mm
< 3.5 mm
▷ Test the screw head and shank size by insert -
ing the screws into one of the keyhole shaped
apertures of the wall-mounting plates before
attaching the plates to the wall.
4 Once the screws are fixed into the wall, insert
the four screw heads through the large opening
of the keyhole-shaped apertures.
5 Then slide the OnCell G3150A-LTE downwards.
6 Tighten the four screws for added stability.
Wiring
WARNING
Safety First!
Be sure to disconnect the power cord before install-
ing and/or wiring your Moxa OnCell G3150A-LTE.
EXPLOSION HAZARD!
Do not disconnect equipment unless you have
removed the power source to the equipment or
the area is known to be non-hazardous.
▷
Use separate paths to route wiring for power
and devices.
▷ If power wiring and device wiring paths must
cross, make sure the wires are perpendicular
at the intersection point.
▷
Do not run signal or communications wiring and
power wiring in the same wire conduit. To avoid
interference, wires with different signal charac-
teristics should be routed separately.

5
D
GB
F
NL
I
E
OnCell G3150A-LTE-EU · Edition 09.18 · GB
▷ You can use the type of signal transmitted
through a wire to determine which wires should
be kept separate. The rule of thumb is that wir-
ing with similar electrical characteristics can be
bundled together.
▷Keep input wiring and output wiring separate.
▷It is strongly advised that you label wiring to all
devices in the system when necessary.
ATTENTION
– This product is intended to be supplied by a Listed
Power Unit marked “Class 2” or “LPS” and rated
O/P: 9.6 W (12 V/0.78 A to 48 V/0.2 A).
– Make sure that the external power adapter (in-
cludes power cords and plug assemblies) pro-
vided with the unit is certified and suitable for use
in your country.
– Use the antennas correctly!
Wide-band (2G/3G/4G) antennas are needed
when the OnCell G3150A-LTE operates. Make
sure that your antenna installation is within a safety
area, which is covered by a lightning protection
or surge arrest system.
WARNING
Do not locate the antenna near overhead power
lines or other electric light or power circuits, or
where it can come into contact with such circuits.
When installing the antenna, take extreme care not
to come into contact with such circuits, because
they may cause serious injury or death when there
is a surge. For instructions on proper installation
and grounding of the antenna, refer to national and
local codes (for example, U.S.: NFPA 70, National
Electrical Code, Article 810, and Canada: Canadian
Electrical Code, Section 54).
Grounding the Moxa OnCell G50A-LTE
▷
Grounding and wire routing help limit the ef-
fects of noise due to electromagnetic interfer-
ence (EMI). Run the ground connection from the
ground screw to the grounding surface prior to
connecting devices.
▷ The minimum cross-sectional area of the ground-
ing conductor should be equal to that of the
input cable.
ATTENTION
This product is intended to be mounted on a well-
grounded mounting surface, such as a metal panel.
The potential difference between the two ground
potentials must be zero. If the potential difference
is NOT zero, the product could be permanently
damaged.
Connecting the Power Input
▷
Input Terminal Block (J3) is suitable for 12-28
AWG (3.31-0.0804 mm2) wire size, torque value
4.5 lb-in (0.51 Nm).
Pinouts for the Power Inputs and Relay
Output
V1+
V1-
V2+
V2-
I1
COM 1
I2
COM 2
Pin Name Usage
1V1+ DC Power Input 1
2V1-
3V2+ DC Power Input 2
4V2-
5Relay Output
6
7I1 Digital Input
8COM 1 Digital Input GND
9I2 Digital Input
10 COM 2 Digital Input GND
Wiring the Redundant Power Inputs
ATTENTION
Before connecting the OnCell G3150A-LTE to the
DC power inputs, make sure that the DC power
source voltage is stable.
▷The top two pairs of contacts of the 10-contact
terminal block connector located on the top
panel of the OnCell G3150A-LTE are used as
the two DC inputs.
V1+
V1-
V2+
V2-
V1+
V1-
V2+
V2-
Top
Front
 Insert the negative/positive DC wires into the V-/
V+ terminals.
 To keep the DC wires from pulling loose, use a
small flat-blade screwdriver to tighten the wire-
clamp screws on the front of the terminal block
connector.
 Insert the plastic terminal block connector prongs
into the terminal block receptor, which is located
on the top panel of the OnCell G3150A-LTE.
Wiring the Relay Contact
▷
The OnCell G3150A-LTE has one relay output,
which consists of the two contacts of the terminal
block on the OnCell G3150A-LTE’s top panel.
▷ For detailed electrical requirement, see page
7 (Specifications).

6
D
GB
F
NL
I
E
OnCell G3150A-LTE-EU · Edition 09.18 · GB
▷ The relay contacts are used to indicate user-
configured events. The two wires attached to
the relay contacts form an open circuit when
a user-configured event is triggered. If a user-
configured event does not occur, the relay circuit
will be closed.
Wiring the Digital Inputs
▷The OnCell G3150A-LTE has two sets of digital
inputs—DI1 and DI2.
▷
Each DI comprises of two contacts on the 6-pin
terminal block connector located on the top
panel of the OnCell G3150A-LTE.
▷For detailed information on isolated digital input
definition, see page 7 (Specifications).
Communication Connections
0/00BaseT(X) Ethernet Port Connection
▷The 10/100BaseT(X) ports located on the front
panel of the OnCell G3150A-LTE are used to
connect to Ethernet-enabled devices.
▷ Pinouts for both MDI (NIC-type) ports and MDI-X
(HUB/Switch-type) ports:
MDI Port
Pinouts
MDI-X Port
Pinouts 8-Pin RJ45
Pin Signal Pin Signal
1Tx+ 1Rx+
1 2 3 4 5 6 7 8
2Tx- 2Rx-
3Rx+ 3Tx+
4Rx- 6Tx-
Serial DB9 Connection
▷
The OnCell G3150A-LTE has one DB9 male port
that supports RS-232, RS-485-4W, RS-485-2W,
and RS-422:
Pin assignments DB9 Male
Connector
Pin RS- RS-4/
485-4w
RS-
485-w
1DCD TxD-(A) –
1 5
6 9
2RxD TxD+(B) –
3TxD RxD+(B) Data+(B)
4DTR RxD-(B) Data-(A)
5GND GND GND
6DSR
7TRS
8CTS
9 – – Tx-
RS- Console Connection
▷
The OnCell G3150A-LTE has one RS-232 (8-pin
RJ45) console port located on the front panel.
▷ Use either an RJ45-to-DB9 or RJ45-to-DB25
cable to connect the Moxa OnCell G3150A-LTE’s
console port to your PC’s COM port.
▷ You may then use a console terminal program to
access the OnCell G3150A-LTE for configuring
the console configuration.
Console Pinouts for 0-Pin or 8-Pin RJ45
0-Pin Description 8-Pin
1 –
1 2 3 4 5 6 7 8
2DSR 1
3RTS 2
4GND 3
5TxD 4
6RxD 5
7 – 6
8CTS 7
9DTR 8
10 –
▷
The pin numbers for both 8-pin and 10-pin RJ45
connectors (and ports) are typically not labeled
on the connector (or port).
LED Indicators
▷
The front panel of the Moxa OnCell G3150A-LTE
contains several LED indicators.
Function of LEDs
Type Color State Description
Signal
(1 LED)
Green Blinking The number of blinks indicates
the cellular signal level (once the
device is connected to a cellular
network with an IP address.)
Interval between two blinks:
200 ms
Gap: 2 seconds
No. of
Blinks
Cellular
RSSI
RSSI Ran-
ge (dBm)
10 < SNR
≤ 12
113 <
RSSI ≤
-89
2
12 <
SNR ≤
21
-89 < RSSI
≤ -73
3
22 <
SNR ≤
31
-73 < RSSI
≤ -51
The Cellular RSSI value is based
on the OnCell device signal
strength returned by the AT+
CSQ AT command. You can
also refer to the equivalent signal
RSSI Range (dBm) provided in
the table above.
PWR1/
PWR2
Green On DC power source active
Off Power is off
Ready Green On
System startup is complete and
the system is in operation
Blinking
(slow at
1-sec
intervals)
The OnCell device has been lo-
cated by the
Wireless Search Utility.
Off
Power is off, or device is boo-
ting up.
Fault Red On
Device is booting up, or IP
address conflict.
Blinking
(slow at
1-sec
intervals)
Cannot get an IP address from
the DHCP
server
Off
Power is off or no error condition
exists.

7
D
GB
F
NL
I
E
OnCell G3150A-LTE-EU · Edition 09.18 · GB
Function of LEDs
Type Color State Description
2G/3G Amber Blinking
(slow at
500-ms
intervals)
GSM/GPRS/EDGE is connected.
On UMTS/HSPA is connected.
Off GSM/GPRS/EDGE/UMTS/
HSPA is
disconnected.
4G Amber On LTE is connected
Off LTE is disconnected.
SIM1 Amber On/Off SIM 1 is active or inactive
Blinking
SIM 1 is not inserted or PIN code
is incorrect
SIM2 Amber On/Off SIM 2 is active or inactive
Blinking
SIM 2 is not inserted or PIN code
is incorrect
GPS Green On GPS signal has been located
Blinking Locating GPS signal or
less than four satellites have
been located.
Off
GPS signal has not been located
TX Rx Amber On The serial port is transmitting
data
Off No data is being transmitted or
received
through the serial port
Specifications
Cellular Specification
Standards: GSM/GPRS/EDGE/UMTS/HSPA/LTE.
Band Options:
OnCell G3150A-LTE-EU:
B1 (2100 MHz)/B3 (1800 MHz)/B7 (2600 MHz)/B8
(900 MHz)/B20 (800 MHz),
UMTS/HSPA 2100/1900/850/800/900 MHz,
OnCell G3150A-LTE-US:
B2 (1900 MHz)/B4 (AWS)/B5 (850 MHz)/ B13 (700
MHz)/B17 (700 MHz)/B25 (1900 MHz),
UMTS/HSPA 2100/1900/AWS/850/900 MHz,
Universal quad-band GSM/GPRS/EDGE/1800/1900
MHz.
LTE Data Rate:
Category 3 Downlink: 100 Mbps (20 MHz bandwidth),
50 Mbps (10 MHz bandwidth) Uplink: 50 Mbps (20
MHz bandwidth), 25 Mbps (10 MHz bandwidth).
HSPA Data Rate:
Downlink: Up to 42 Mbps (category 24) Uplink: Up
to 5.76 Mbps (category 6).
GPRS Data Rate:
Downlink/Uplink: 85.6 kbps DL, 42.8 kbps UL.
Interface
Cellular Antenna Connectors:
2 SMA (female), MIMO for LTE, antenna diversity
for WCDMA.
SIM Slots: Dual SIM card support, full-sized SIM (1FF).
GNSS:
1 SMA (female), GPS: 1575.42 MHz, GLONASS:
1602 MHz.
Ethernet:
1, 10/100 Mbps auto negotiation speed, F/H duplex
mode and auto MDI/MDI-X connection (RJ45-type).
Serial Console Port:
1, RS-232 (RJ45-type).
Serial Port:
1, RS-232, RS-485-4W , RS-485-2W, RS-422 (DB9
male).
Serial Communication Parameters:
Data Bits: 5,6,7,8,
Stop Bits: 1,1.5, 2 (when parity = None),
Parity: None, Even, Odd, Space, Mark,
Baudrate: 75 bps to 921.6 kbps.
LED Indicators:
PWR1, PWR2, READY, FAULT, CELLULAR SIGNAL,
SIM1, SIM2, 2G/3G, 4G, GPS, TX/RX.
Alarm Contact: 1 relay output with current carrying
capacity of 1 A @ 24 VDC.
Digital Inputs:
2 electrically isolated inputs:
+13 to +30 V for state “1”,
+3 to -30 V for state “0”,
Max. input current: 8 mA.
Ground Screw: M5.
Reset Button: Power reset/factory default reset.
Software Specification
Network Protocol:
ICMP, TCP/IP, UDP, DHCP, Telnet, DNS, SNMP, HTTP,
HTTPS, SMTP, SNTP, ARP.
Routing/Firewall:
NAT, port forwarding, IP/MAC/port filtering.
VPN:
Max. Tunnel Number: 5 (Responder/Initiator)
IPsec (DES, 3DES, AES, MD5, SHA-1, DH2, DH5),
PSK/X.509/RSA,
GRE over IPsec,
Open VPN,
NAT-T, PFS, DPD.
Management Options:
Remote SMS Control, SNMPv1/v2c/v3, Web/Telnet/
Serial Console.
Others: DDNS.
Software Specifications (Moxa Proprietary)
GuaranLink: Dual SIM 4-tiers heart-beat for reliable
and persistent cellular connectivity.
OnCell Central Manager: Large scale centralized de-
vice management over private cellular IP addresses.
Search Utility:
Simple device configuration and management utility.
Physical Characteristics
Housing: Aluminum, providing IP30 protection.
Mounting:
DIN rail (default) or wall mount (optional).
Input Terminal Block (J3):
Suitable for 12-28 AWG (3.31-0.0804 mm2) wire size,
torque value 4.5 lb-in (0.51 Nm). The minimum cross-
sectional area of the grounding conductor should be
equal to that of the input cable.
Weight: 492 g (1.08 lb).

© 2018 Elster GmbH
8
D
GB
F
NL
I
E
OnCell G3150A-LTE-EU · Edition 09.18 · GB
For More Information
The Honeywell Thermal Solutions family of products includes
Honeywell Combustion Safety, Eclipse, Exothermics, Hauck,
Kromschröder and Maxon. To learn more about our products, visit
www.ThermalSolutions.honeywell.com or contact your Honeywell
Sales Engineer.
Elster GmbH
Strotheweg 1, D-49504 Lotte
T [phone]
[email protected], www.kromschroeder.de
Elster is part of Honeywell
Honeywell Thermal Solutions – Support Line
T ++1 888-516-9282
[email protected]
Original operating manual
Dimensions:
141.8
(5.58)
126.0
(4.96)
107.5
(4.23)
117.9
(4.64)
30.0
(1.18)
Installation:
DIN-rail mounting, wall mounting (with optional kit).
Environmental Limits
Operating Temperature:
Standard Models: 0 to 55°C (32 to 131°F),
Wide Temp. Models: -30 to 70°C (-22 to 158°F).
Storage Temperature: -40 to 85°C (-40 to 185°F).
Ambient Relative Humidity:
5 to 95% (30°C, non-condensing).
Power Requirements
Input Voltage:
12 to 48 VDC, redundant dual DC power inputs.
Connector: 4-pin removable terminal block.
Power Consumption:
9.6 W (12 V/0.78 A to 48 V/0.2 A).
Reverse Polarity Protection: Present.
Reliability
MTBF: > 528,596 hours.
Standards and Certifications
Safety
OnCell G3150A-LTE-US: UL 60950-1.
EMI
OnCell G3150A-LTE-US: FCC Part 15 Subpart B.
EMS
OnCell G3150A-LTE-EU: EN 61000-6-2/-4.
Radio
OnCell G3150A-LTE-US:
FCC ID N7NMC7355,
OnCell G3150A-LTE-EU:
EN 301 489-1, EN 301 489-7, EN 301 511/4.
ATEX Zone  Certification Information
Demko 16 ATEX 1812X,
II 3 G Ex nA IIC T5 Gc,
Ambient Range:
-30°C ≤Tamb ≤ +70°C.
IECEx UL 16.0166X
Hazardous Location Standards
EN 60079-0:2012+A11:2013 / IEC 60079-0
6th Edition,
EN 60079-15: 2010 / IEC 60079-15 4th Edition.
ATTENTION
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference re-
ceived, including interference that may cause un-
desired operation.
Warranty
Warranty Period: 5 years.
Details:
See www.moxa.com/support/warranty.aspx.