Hot Shot S22258 Dimensions

DESCRIPTION
Structure in aluminium
Powder coated
3.66 x 2.14 m
CONFORM
European standard
NF EN 750
PRODUCT SHEET
ALUMINIUM HOCKEY GOAL
PRODUCT REF :S22258 PAIR
ASSEMBLY TIME
The time to make the assembly of this goal is estimated, for 2 people, at 45 minutes. (without sealing).
TEST AFTER INSTALLATION
According to the decree above, for the first installation the goal must be tested like below :
-Put a vertical and static charge of 180 kg, on the middle of the crossbar,
- Put an horizontal charge of 110kg at the same point
After testing, the equipment and the fixation system or counterweight should not fail, displace or deform.
When the goal is not used it must be sealed or be stocked somewhere that people can’t used it.
During the first installation, this stability and solidity test is compulsory.
Every time that the equipment is assembled, a visual check of the stability and solidity must be realized.
The owner must regularly check the condition of the product, and be sure that it meets the current safety standards.
In order to use our products at there best, it is recommended to follow carefully the notice of instruction, where you
can find the conditions of assembly ; installation ; maintenance ; storing.
MAINTENANCE
The equipement has to be regularly maintained by the owner. It is adviced to:
- Check every week that all the screws are correctly tightened
- Fix paint defects if the module has been damaged, using the adapted paint, specified by the manufactu-
rer.
- Replace all damaged or missing parts with a spare part recommended by the manufacturer.
- Clean the product by using dishwasher soap, clean water, and soft cloth.
WARRANTY
One full year parts and labor guarantee. Every claim regarding condition of the delivered equipment has to
be done within the legal period of the reception of the material. The warranty will not apply to:
- all degradation during the transport.
- all degradation due to use differing from which was intended.
- all degradation due to poor maintenance.
- any defect claimed after the end of the legal period.
- any damaged due to a faulty installation and assembly of the module

2
- Realize the sealing with concrete CPJ45 dosed by 350 kg.
- Once the concrete has been poured in the hole, put the anchor’s tubes and verify
that their implantation is conform to the dimensions of the drawing above.
- Wait at least 72 hours for the concrete to be dry
IMPLANTATION & SEALING
1000±10mm
2000±10mm
Field limit
Concrete bloc
500x500x500mm Concrete bloc
500x500x500mm
A
500
GROUND
Concrete
500x500x500mm
Important : The distance A has to be
determined by the installer. When the
goal is not used, the top of the cap
must be at the same level than the
ground.
2500±10mm
1250±10mm

3
ASSEMBLY
1– ASSEMBLY OF CROSS-BAR TO THE 2 SIDE FRAMES (x4)
NECESSARY
ITEMS
NECESSARY TOOLS (NOT INCLUDED)
INCLUDED ITEMS
x12
Split lock was- hers 10
Wrench 17mm Allen wrench 6mm
x12
Screws M10x70
x4
Countersunk
screws M10x30
x46
Countersunk
screws M8x30
x1
Countersunk
screws M10x30
Cross bar
Left side frame
Countersunk screws M10x30
Allen wrench 5mm
x4
Anchorage
x4
Hook
x4
Stainless
steel eyebolt
x4
SS washers 12

4
2– ASSEMBLY OF REAR FRAME TO THE SIDE FRAMES (x4)
NECESSARY
ITEMS
ASSEMBLY
Screws M10x70 +
spring washer 10
x3
Split lock was- hers 10
NECESSARY
ITEMS
Countersunk screws M8x30
x28
Countersunk
screws M8x30
x3
Screws M10x70
3– ASSEMBLY OF NET (x2)
Remove the rods, put the
net in position and fix the
rods again

5
4– FIXATION OF THE PRODUCT TO THE GROUND (x4)
NECESSARY
ITEMS
ASSEMBLY
SS eyebolt +
SS washer 12
Hook
x1
Anchorage
x1
Hook
x1
Eyebolt
x1
SS washers 12

NOMENCLATURE
Package
N° Ref Index Designation Description Quantity Packing Method Weight (kg)
Dim.
(mm)
A1 S22258-01 BCross-bar 2Plastic bubble +
carton 2 layers 11 3750x120x100
A2
S22258-02 +
S22258-051
D +
A
Side right frame +
Rod for net tension, lg
1160
1 + 1
Plastic bubble +
carton 2 layers
27 2300x1520x100
A3 1 + 1 27 2300x1520x100
A4
S22258-03 +
S22258-051
D +
A
Side feft frame +
Rod for net tension, lg
1160
1 + 1
Plastic bubble +
carton 2 layers
27 2300x1520x100
A5 1 + 1 27 2300x1520x100
A6 S22258-04 +
S22258-052+
S22258-053
E
Back frame +
Rod for net tension, lg
2000 +
Rod for net tension, lg
1648
1 + 1 + 1
Plastic bubble +
carton 2 layers
42 3800x500x100
A7 1 + 1 + 1 42 3800x500x100
A8 S22258-09 AAccessories package 14
ACCESSORIES PUT IN CLEAR PVC BAG
Package
N° Reference Designation Description Qty Note
A8 BITJ1030 SS countersunk hex
screw M10x30 4
To assemble the
cross-bar with the
side frames
A8 BITH1070 +
LITB101625
SS screw M10x70 + Split
lock washers 10 12+12
To assemble the side
frames to the back
frame
A8 Anchorages 4To be anchored into
the ground
S22258-08
A8
Hook +
SS Eye bolt M12x130 +
Stainless steel washer 12
4 + 4 + 4 To fix the product to
the ground
A8 Steel cap 4
To cover the ancho-
rage when the goal is
not used
PRE-ASSEMBLED ACCESSORIES
Package
N° Reference Designation Description Qty Note
A6+A7 LITA164020 + TITD16 Wheel axe + SS washer 16
+ SS locknut 16 4+8+4
To assemble the
wheels
A6+A7 BXN15040 + OBI6203 PA wheel D150 + bearing
6203 8+16
A2+A3+
A4+A5+
A6+A7
Socket M8 46
A2+A3+
A4+A5+
A6+A7
BITJ830 SS countersunk hex
screw M8x30 46 Already used to fix the rods on frames
A2+A3 Conformity stickers 2Stuck on the post
VISA PACKING DEPARTMENT DATE :
PACKING LIST
HOCKEY GOAL ALUMINIUM
PRODUCT REF S22258 Index G PAIR