Hougen HMD968 User manual
POWER FEED MAGNETIC DRILL
OPERATOR’S MANUAL
FOR USE WITH “12,000-SERIES” HOUGEN
®
CUTTERS
® CUTTERS
®
HMD968
covers
0968402 & 0968404
2
HOUGEN
®
Portable Magnetic Drill
Model HMD968
Welcome to Hougen
Congratulations on your purchase of the Hougen
®
Portable Magnetic Drill Model HMD968. Your model is designed to
produce superior holes quickly and effi ciently. Through constant innovation and
development, Hougen is committed to provide you with hole-producing tools and products to help you be more pro-
ductive.
Before attempting to operate your new Portable Magnetic Drill, please read all instructions fi rst. These include the
Operator’s Manual and Warning Label on the unit itself. With proper use, care, and maintenance, your model will
provide you with years of effective hole drilling performance. Once again, thank you for selecting our product and
welcome to Hougen.
Listed below are the Part Numbers and Desciptions of the Hougen HMD904 Series. Please review
Parts Diagram for the location of the Part No./ Serial No. Label.
0968402-HMD968, 230 volt, Power Feed, Coolant without an electrical plug.
0968404-HMD968, 230 volt, Power Feed, Coolant and Swivel Base, without an electrical plug.
Cutter Type........................Hougen “12,000-Series”
Hole Capacity....................12mm - 38mm Manual Mode
12mm - 32mm Power Feed Mode
Depth of Cut......................50mm
Motor................................. 700 RPM, 3A
Net Weight........................ 16.7 kg, 18.9 kg w/swivel
Swivel Area....................... 28.5mm W x 34.9 mm L
Specifi cations
Hougen Manufacturing, Incorporated warrants its Portable Magnetic Drills and its Electro-hydraulic Hole Punchers for a period
of 1 year and other products for ninety (90) days from date of purchase against defects due to faulty material or workmanship
and will repair or replace (at its option) without charge any items returned. This warranty is void if the item has been damaged
by accident or unreasonable use, neglect, improper service, or other causes not arising out of defects in material or workman-
ship. No other expressed warranty is given or authorized. Hougen Manufacturing, Inc. disclaims any implied warranty of
MERCHANTABILITY or FITNESS for any period beyond the expressed warranty and shall not be liable for incidental or
consequential damages. Some states do not allow exclusions of incidental or consequential damages or limitation on how long
an implied warranty lasts and, if the law of such a state governs your purchase, the above exclusion and limitation may not
apply to you. This warranty gives you specifi c legal rights and you may also have other rights which vary from state to state.
To obtain warranty service, return the item(s), transportation prepaid, to your nearest Factory Authorized Warranty Repair
Center or to Hougen Manufacturing, Inc., 3001 Hougen Drive, Swartz Creek, Michigan 48473.
Hougen Drills are warranted against manufacturing defects only. Subject to Hougen Manufacturing inspection.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
© 2011 Hougen Manufacturing, Inc.
Commercial /
I
ndustrial
L
imited
W
arranty
Photographs and Specifi cations shown are accurate in detail at time of printing. Manufacturer reserves the right to make
improvements and modifi cations without prior notice.
Hougen, Rotabroach, and Hougen-Edge are proprietary trademarks of Hougen Manufacturing Inc.
UNPACKING YOUR NEW MAGNETIC DRILL
1
.
Open shipping carton and remove the literature and
hardware packages.
2.
Read and Follow All Instructions
before attempting
to operate your new Magnetic Drill.
3.
Complete and mail the Product Registration Card
now
.
It is important that Hougen Manufacturing, Inc. have a
record of product ownership.
4.
Open hardware package and check contents.
10565 1/8” Hex wrench for Gib Adjustment
04558 Feed handles (3)
04532 Feed handle knobs (3)
90724 Safety chain
02635 3/16” Hex wrench for cutter installation
13013 5/32” Hex wrench
5.
Using the handle of Magnetic Drill, lift unit out of the
shipping case.
6.
Remove all packing and securing material from the drill
unit.
7.
Screw the three Knobs (04532) into the three
Feed Handles (04558) and then screw Handles
into the Hub Assembly (19030). Do not overtighten
or may strip the knobs.
8.
Your Magnetic Drill was factory adjusted prior to
shipping. Check to make sure that all gib
adjustment screws, motor mount screws, front
support bracket screws, and magnet mounting
screws are snug and have not vibrated loose in
transit.
9.
Your new Magnetic Drill comes complete with
arbor mounted. The 3/4” diameter arbor bore
fi ts all 3/4”-shank “12,000-Series” Hougen
Cutters.
Reread Safety Warnings listed in the Operator’s
Manual and on the drill unit to avoid injury. Follow
operating procedures.
3
Always wear eye protection while
using cutting tools, or in the vicin-
ity of cutting.
CAUTION!
The slug is ejected
at the end of the cut. Do not aim
cutter or arbor so that ejected
slug may hit someone around, or
below you.
CAUTION!
Cutters are sharp.
Wear gloves when installing or
removing cutter from arbor. Do
not grab a rotating cutter.
CAUTION!
To prevent electric
shock, do not use power tools
near wet areas, or where power
tool may become wet.
SAFETY FIRST
HINTS FOR SMOOTHER OPERATION 11
MOTOR EXPLODED VIEW 12
ELECTRICAL PANEL PARTS 13
WIRING DIAGRAM 14
EXPLODED VIEW 16-17
EXPLODED VIEW W/SWIVEL BASE 18-19
PARTS LIST 20-21
DRILL MAINTENANCE & PROBLEM SOLVING 22
WARRANTY SERVICE CENTERS 24
WELCOME TO HOUGEN 2
UNPACKING YOUR DRILL 3
SAFETY INSTRUCTIONS 4 - 5
SAFETY SWITCH INDICATOR LIGHT
5
CONTROL PANEL 6
OPERATING INSTRUCTIONS 7
INSTALLING HOUGEN CUTTERS 8
CUTTING FLUID RESERVOIR 8
ARBOR & GIBS ADJUSTMENT 9
SWIVEL BASE OPERATION
10
INDEX
4
Important Safety Instructions
W
ARNING:
WARNING:W
Read and understand all instructions.
Failure to follow all instructions listed belo
w
,
may result in electrical shock, fire and/or serious personal injur
y
.
5
SAFETY SWITCH
INDICATOR LIGHT
The Safety Switch Indicator Light is a Standard Safety
Feature on HMD968 magnetic drills. Its purpose is to inform
the user that an unsafe condition exists.
If light is Green:
In normal operation the safety switch light will be green.
Motor “On” and “Off” Switches function normally.
If light is Red:
A condition with the safety switch exists that needs to be
corrected.
Possible causes:
• Safety Switch is defective. Have drill serviced.
• Uneven work surface or material. Check work
surface for fl atness.
• Dirt or chips under magnet. Clean work surface.
HOUGEN MANUFACTURING RECOMMENDS THAT
CONDITIONS ARE CORRECTED SO LIGHT TURNS
GREEN. THIS ALLOWS FOR THE UNIT TO BE
OPERATED IN A SAFE MANNER.
For any questions please contact Hougen Manufacturing’s
Technical Service at (810) 635-7111.
Extension Cord
T
able
TableT
Plugs and Receptacles
I
Important Safety Instructions - Continued
W
ARNING:
WARNING:W
Read and understand all instructions.
Failure to follow all instructions listed belo
w
,
may result in electrical shock, fire and/or serious personal injur
y
.
6
OPERATION OF CONTROLS
BEFORE INSTALLING HOUGEN CUTTER
IMPORTANT: Before turning on the machine, it is important that the operator understands the interrelated
functions of the SAFETY SWITCH, MAGNET SWITCH, AND MOTOR SWITCHES.
READ SAFETY SWITCH INDICATOR LIGHT INSTRUCTIONS PREVIOUS PAGE.
SAFETY SWITCH
— Located in base of drill. Enables motor operation only when magnet is
properly seated on a clean and fl at work surface. Turns motor off if switch
detects lift of unit.
MAGNET ON/OFF SWITCH
— Energizes and De-Energizes the magnetic base and activates the
safety switch. Motor can now be started by pushing the motor START switch.
MOTOR START/STOP SWITCHES
— Starts and Stops the motor (See instructions previous page).
POWER/MANUAL FEED SWITCH
— Enables or disables Power Feed Mode.
1. Place Magnetic Drill on clean, fl at steel plate that is at least 3/8” thick.
2. Plug unit into proper AC power source.
DO NOT use with DC Power.
3. Locate the Magnet
ON
and
OFF switches
and the motor
STOP
and
START
switches.
4.
NOTE: A loss of power will de-energize the magnetic base and deactivate the motor.
When power is restored, the magnet will reenergize, however, the motor START switch
must be depressed before the motor will start.
1. Make sure workpiece and bottom of magnet are free of chips, oil, etc.
2. Position drill by sliding it and gently feeding Arbor so that pilot point is
touching center of hole to be drilled.
3. Secure unit to workpiece with safety chain.
4. On the Control Panel, fl ip Power/Manual Feed Switch to
Power Feed
.
5. Turn Magnet ON with the Magnet Rocker Switch.
6. Turn On Cutting Fluid and check for proper fl ow by slightly depressing
pilot on work surface.
7. Make certain that cutter is clear of workpiece by 3mm and turn
motor ON by pressing the motor START switch.
8. In center of feed handles
Flip Power Feed Handle
out to engage
Power Feed Motor. The unit will feed itself into and through
the workpiece.
9. At conclusion of cut, motor will automatically turn OFF.
CAUTION: Slug can eject with force and distance.
Disengage Power Feed Handle then turn Feed Handles to raise Arbor
and make sure slug has fallen free.
10. Turn magnet OFF by pressing the magnet OFF switch.
11.
Disconnect from power source.
12. If necessary, remove chips from cutter and magnet, preferably wearing
leather work gloves and/or with pliers.
13. Disconnect safety chain and you are ready to move unit to new drilling
position.
OPERATING INSTRUCTIONS
Power Feed Mod
e
Manual
Feed Mod
e
Always remember that the magnet’s holding power is directly related to the workpiece thickness and surface
condition. Since magnetic attraction diminishes with thinner material or rough surfaces, mechanical clamping
of drill unit to the workpiece should be used when cutting thin material (9.5mm or less) or material with uneven
surfaces.
1. Make sure workpiece and bottom of magnet are free of chips, oil, etc.
2. Position drill by sliding it and gently feeding Arbor so that pilot point is
touching center of hole to be drilled.
3. Secure unit to workpiece with safety chain.
4. On Control Panel Flip Power/Manual Feed Switch to
Manual
.
5. Turn magnet ON by pressing the magnet ON switch.
6. Turn Feed Handle, raising the cutter until the pilot is above the work
surface.
7. Turn on coolant bottle.
8. Make certain that cutter is clear of workpiece and turn motor ON by
pressing the motor START switch.
9. Feed Cutter slowly into workpiece. Only after cutting path is established
to a depth of about 2mm can full force be applied to feed handles.
10.
Ease up on feed pressure
Ease up on feed pressure
as cutter starts breaking through.
11. At conclusion of cut, turn motor OFF by pressing motor STOP switch.
CAUTION: Slug can eject with force and distance.
Turn Feed Handles to raise Arbor checking to make sure the slug has
fallen free.
12. Turn magnet OFF by pressing the magnet OFF switch.
13.
Disconnect from power source.
14. If necessary, remove chips from cutter and magnet, preferably wearing
leather work gloves and/or with pliers. Disconnect safety chain and you
are ready to move unit to new drilling position.
Power Feed
Manual Feed
7
Power Feed
Engagement Handle
Step 5
Step 8
INSTALLING HOUGEN CUTTER IN ARBOR
1. Disconnect from power source.
2. Lay drill on its side with feed handles up or be sure Arbor clears table
if unit is in normal operating position.
3. Turn Feed Handles until cutter mounting set screws are exposed
and completely remove the set screw.
4. Insert proper pilot in shank end of Hougen Cutter.
5. Insert Hougen Cutter until fl at on cutter shank is aligned with set
screw holes and is exactly perpendicular to axis of set screw holes.
6. Insert set screws and tighten.
OPERATION OF CUTTING FLUID RESERVOIR
1. With Drill in operating position, turn the feed handles
so that cutter and pilot are above the work surface.
2. Fill reservoir by removing cap on bottle.
3.
Turn on coolant bottle.
4. Test metering capabilities of Arbor/Cutter/Pilot assembly
(magnet ON-motor OFF) by feeding the Arbor gently
toward work surface until pilot is pushed up into Cutter,
thus allowing fl uid to fi lter down onto work surface
through a groove in the pilot.
5. Fluid output can be adjusted by position of On/Off Valve.
8
On/Off Valve
Adjust Gibs before adjusting front support bracket.
1. Loosen Arbor Support Bracket Bolts.
3. Be sure top of arbor is fl ush with the shoulder on motor output shaft. Also make certain arbor is securely
fastened.
4. Turn feed handle until motor and spindle are at the bottom of their travel.
5. Tighten Arbor Support Bolts.
6. Feed slide up and down a few times, checking for free and uniform movement.
NOTE: Check Arbor support bolts regularly to make certain they are tight. Tighten as required.
ADJUSTMENT OF GIBS
1. Loosen all Gib Screws.
2. Feed the drill in and out a few times and then, with top of motor slide fl ush with top of housing, tighten the Gib
Screws until you feel them touch the Steel Gib.
3. Feed the drill in and out again.
4. Adjust Gib Screws so that there is uniform pressure from top to bottom. (Top of motor slide fl ush with top of
housing.)
5. Turn each Gib Screw in about 1/8 to 1/4 turn, depending upon your preference.
6. Gibs should be tight enough so that slide moves up and down smoothly with no wobble or shaking.
(Looseness will cause cutter breakage.)
NOTE: Gibs should be lubricated regularly.
ARBOR ADJUSTMENT
9
Removal
1. Loosen arbor support bracket bolts.
2. Remove coolant bottle.
3. Loosen set screws holding arbor onto motor output shaft.
4. Remove arbor.
Installation
1. Hand tighten front support bracket bolts. Do not tighten all the way.
2. Slide arbor to full up position and hold arbor in position over hex drive motor output shaft.
3. Tighten two set screws to hold arbor onto motor output shaft.
4. Turn feed handle until motor and arbor are at the bottom of their travel.
5. Tighten front support bracket bolts to 400 in/lbs.
6. Run motor for 10 seconds. (If visual movement of arbor is noticed, restart at step 1)
7. Re-check for tightness of arbor set screws.
8. Install coolant bottle.
ARBOR & FRONT SUPPORT BRACKET
REMOVAL AND INSTALLATION
To Loosen the Swivel Plate Assembly
1. Lift the Clamp Handle Assembly,
rotated counter-clockwise and release .
This will reposition the lever
for more movement.
With this being a left handed thread this will loosen this assembly.
3. If more travel is needed lift the Clamp Handle Assembly, rotate counter clockwise
and release.
4. Pull the Clamp Handle Assembly clockwise again.
This amount of movement should be adequate to reposition the Drill Assembly.
More movement than this may cause the Magnet Assembly to disengage from the drill base.
To Tighten the Swivel Plate Assembly.
1. Lift the Clamp Handle Assembly,
rotated clockwise and release .
This will reposition the lever
for more movement.
With this being a left handed thread this will tighten this assembly.
3. If more travel is needed lift the Clamp Handle Assembly, rotate clockwise and release.
4. Push the Clamp Handle Assembly counter clockwise again.
Continue this process until the Swivel Assembly is tight.
�WARNING :�
�
2. With the Clamp Handle Assembly now down,
pull the Clamp Handle Assembly clockwise.
2. With the Clamp Handle Assembly now down,
push the Clamp Handle Assembly counter clockwise.
CLAM
P
HANDLE MUST BE TIGHT PRIOR
T
O CUTTING HOLES -
EQUIPMENT DAMAGE OR PERSONA
L
INJU
R
Y
RYR
COULD OCCUR
Y COULD OCCUR Y
ATTENTION
The threads on the Clamp Handle Assembly are a Left Handed thread meaning,
Turning Clockwise would loosen the assembly
Turning Counter Clockwise would tighten the assembly.
Also, the Clamp Handle Assembly is spring loaded so you will need to lift & turn the entire
Clamp Handle Assembly when repositioning as if to be a ratchet device.
SWIVEL BASE OPERATION
10
11
1. Keep inside of Hougen Cutter clear of chips. Chips will interfere with cutting
to maximum depth and may impede
the free oil fl ow and can cause cutter breakage.
2. Keep work, machine, arbor and Hougen Cutter free of chips and dirt.
3. Tighten all bolts and fasteners regularly.
4. We highly recommend using a light viscosity cutting fl uid (preferably
Hougen Cutting Fluid - Part No. 11742-4)
5. Occasionally check metering of cutting fl uid fl ow. Lack of cutting fl uid may
cause Hougen Cutter to freeze in cut, slug to stick and may result in poor
cutter life.
6. Always start cut with light feed pressure and then increase suffi ciently to
achieve maximum cutting rate.
7. Ease off on pressure as cutter begins to break through at the end of the cut.
8. Keep slide dovetails, brass gibs and feed rack lubricated and free of chips and dirt.
9. When slug hangs up in cutter, turn off motor and bring cutter down on a fl at surface. This will normally straighten a
cocked slug, allowing it to be ejected.
10. When cutting large diameter or deep holes it may be necessary to stop in the middle of the cut to add cutting
fl uid and remove the chips from around the arbor. (When doing this DO NOT raise the cutter out of the hole.
Doing so can allow chips to get under the teeth of the cutter and make it diffi cult to restart the cut.)
* ”Babying” the cutter through the cut will only decrease tool life.
HINTS FOR SMOOTHER OPERATION
#1 cause of cutter
breakage and
prematurely dull
teeth is too little
feed pressure*
HMD968
90960
05538
10538
05537
19033
05817
05526
MOTOR PARTS LIST
MOTOR ASSEMBLY 05818
12
Part # Description Qty
90960
Cable Tie 4”
1
05538
Screw M10 x 1.5 X 16 mm
1
10538
Washer #8 Ext. Tooth
1
05537
Screw M4 x .7 x 6 mm
1
19033
Motor Cord Assy.
1
05817
Label, Motor HMD968
1
05526
Motor. 230 Volt
1
CONTROL PANEL PARTS LIST
Panel Assembly P/N: 19043
13
1
2
3
4
5,6
7
8910
11
12
13
14
15
16
17
18
19
20, 21
22
Feed Motor
Slide Safety
Switch
Magnet Wires
Magnet Safety Switch
Ground from Power Cord Ground to Housing
White or Blue from Power Cord
Black or Brown from Power Cord
Connect
Black Drill Motor White Drill Motor
19043
230v Control Panel Assembly
Item Part # Description Qty
1
05831
Faceplate
1
2
05868
Power Feed Circuit Board
1
3
05827
Circuit Board
1
4
04664
Rocker Switch
1
5
01334
Motor ON Switch
1
6
02409
Green Switch Cover
1
7
05335
Mini Toggle Switch
1
8
04877
Wire Harness
1
9
04878
L.E.D Spacer
1
10
04881
L.E.D. Bulb
1
11
04879
L.E.D Lens
1
12
05336
Toggle Switch Boot
1
13
05331
Jumper Wire J5-J3
1
14
05332
Jumper Wire J6-J5
1
15
05355
Screw #4-40 X 1/4
5
16
04891
3/8 lg. Standoff
5
17
05832
Nylon Standoff
3
18
05320
Screw #4-40 x 1
3
19
05319
Nylon Nut
3
20
01335
Motor OFF Switch
1
21
01228
Red Switch Cover
1
22
01226
Switch Guard
1
CONTROL PANEL HOOKUP
14
Black Power Wire
Motor White Wire
Feed Motor to (P1)
located at the edge of
the Power Feed Board.
Slide Safety Switch
to (J3)
M
agnet Wires to
(J1) & (J2)
Magnet Safety Switch
Green Ground Wires
From Motor.
White Power Wire
Motor Black Wire
Note: Only the 240 V
uses jumper wires 19051
in JP1 & JP2
P3 Together
(J4)
Power Cord Ground
15
NOTES
*05532
05391
*05533
*05050
*05054
*10517
05055
40234
04375
10506*
40234
40398
02429
02422
05528
10560
40038
02430
02431 40077
90028
40237
90028
02428
10553
05534
04721
19033
40398
40302
40301
40300
40300
40295
40301
40302
40303
40332
05988
HOOKS TO
COOLANT
INDUCER
05060
02549
05529
40038 10560
05058
*04986
05061
05059
10983
05357
05187
05203
19042
19018
02411
05628
05358*
**04391
INCLUDED
**
05530
40038
07299
16
*05532
05391
*05533
*05050
*05054
*10517
05055
40234
04375
10506*
40234
40398
02429
02422
05528
10560
40038
02430
02431 40077
90028
40237
90028
02428
10553
05534
04721
19033
40398
05988
HOOKS TO
COOLANT
INDUCER
05060
02549
05529
40038 10560
05058
*04986
05061
05059
10983
05357
05187
05203
19042
19018
02411
05628
05358*
**04391
INCLUDED
**
05530
40038
07299
17
0968402
Exploded View
*05532
*05533
*05050
*05054
*10517
05055
40234
04375
10506*
40234
40398
02429
05899
10560
40038
02430
02431
40237
90028
10553
05534
04721
19033
40398
40302
40301
40300
40300
40295
40301
40302
40303
40332
05988
HOOKS TO
COOLANT
INDUCER
05060
05734
05529
40038 10560
05058
*04986
05061
05059
05357
05187
05203
19042
19018
02411
05628
05358*
**04391
INCLUDED
**
05530
40038
05825
07015
05896
05652
05653
05743
05657
05658
07215
05670
05656
05659
02898
41044
90237
07216
07230
18
*05532
*05533
*05050
*05054
*10517
05055
40234
04375
10506*
40234
40398
02429
05899
10560
40038
02430
02431
40237
90028
10553
05534
04721
19033
40398
05988
HOOKS TO
COOLANT
INDUCER
05060
05734
05529
40038 10560
05058
*04986
05061
05059
05357
05187
05203
19042
19018
02411
05628
05358*
**04391
INCLUDED
**
05530
40038
05825
07015
05896
05652
05653
05743
05657
05658
07215
05670
05656
05659
02898
41044
90237
07216
07230
0968404 Swivel
Exploded View
19
Part # Description Qty Part # Description Qty
01165
Retaining Ring
3
05534
SCR-SHC M5 x .8 x 25mm
4
02217
SCR-SOC #8-32
1
05628
Set Screw 1/4 - 28 x 3/8
2
02411
Strain Relief-Motor Cord
1
05652
Safety Switch Assembly
1
02423
Motor Cord Protector
1
05653
Plunger
1
02428
Rack Gear
1
05656
Swivel Plate
1
02429
Gib-Brass Right
1
05657
Slide Plate
1
02430
Gib-Brass Left
1
05658
Pivot Rod
1
02431
Gib-Steel
1
05659
Clamp Handle Assembly
1
02549
Bolt Assy
1
05670
Retaining Ring
1
02898
Dowel pin
1
05734
Front Support Bracket Assembly
1
02902
Roll Pin
1
05743
SCR-FHSC 1/4-20 x 3/4
1
04375
Front Support Bracket Assy
1
05818
Motor Assy
1
04391
O-Ring for Hex Spindle
1
05825
Rack Gear
1
04532
Knob
3
05896
Magnet Assembly
1
04558
Feed Handle
3
05899
Dove Tail Slide
1
04721
Split Washer
2
05967
Motor Slide Assembly
1
04885
Safety Switch
1
05988
SCR-FHSC #10-32 x 1/2
4
04909
Bracket- Safety Switch
1
07215
Bushing Flange
1
04910
Plunger
1
07216
Locking Hole Plug
4
04986
Rubber Washer
1
07230
Swivel Warning Label
1
05050
Spring
1
07299
Power Cord Assembly
1
05054
Spring Seat
1
10506
SCR-Set 3/8-24
2
05055
Collar
1
10517
Retaining Ring
2
05058
Bracket-coolant inducer
1
10538
Washer #8
1
05059
Holder For Coolant Bottle
1
10553
SCR-SHC 1/4-20
2
05060
Coolant Bottle
1
10560
Washer
6
05061
Knob
1
10836
Retaining Ring
1
05107
Bearing
1
10971
SCR-SHC 1/4-20
2
05114
Spring
1
10972
SCR-BHC #6-32
2
05115
Washer
1
10983
Shield
1
05185
Dowel Pin
1
11053
Screw BHS #8-32
1
05187
Screw SHCS #2-56
2
17271
Spring
1
05203
SCR-SHC #8-32
2
19004
Gear Box Cap
1
05357
1/4 - 28 X 7/8 Set Screw
1
19005
Drive Clutch
1
05358
Washer Shim
1
19006
Shaft Drive Clutch
1
05391
Magnet
1
19008
Gear
1
05528
Slide
1
19010
Hub Plate
1
05529
Coolant Bottle Bracket
1
19013
Spline Shaft
1
05530
Spacer
1
19014
Gear
1
05532
Arbor Assembly
1
19015
Gear & Shaft
1
05533
Arbor Body
1
19016
Gear
2
HMD968 PARTS LIST
20
20
Table of contents
Other Hougen Drill manuals
Hougen
Hougen HMD904 SERIES User manual
Hougen
Hougen HMD150 SERIES User manual
Hougen
Hougen HMD920 Series User manual
Hougen
Hougen HMD115 Series User manual
Hougen
Hougen HMD914 series User manual
Hougen
Hougen HMD927 Series User manual
Hougen
Hougen HMD904 SERIES User manual
Hougen
Hougen 10914S User manual
Hougen
Hougen HMD505 SERIES User manual
Hougen
Hougen HMD904 SERIES User manual
Hougen
Hougen 10925 User manual
Hougen
Hougen HMD150 SERIES User manual
Hougen
Hougen HMD505 SERIES User manual
Hougen
Hougen HMD500 User manual
Hougen
Hougen HMD904 User manual
Hougen
Hougen HMD904C User manual
Hougen
Hougen Rotabroach HMD100 User manual
Hougen
Hougen HMD505 SERIES User manual
Hougen
Hougen HMD115 Series User manual
Hougen
Hougen HMD501 User manual
Popular Drill manuals by other brands
Matco Tools
Matco Tools MT1885 Operating instructions, warning information, parts breakdown
Makita
Makita BHR241 instruction manual
Craftsman
Craftsman 315.115760 Operator's manual
DeWalt
DeWalt DW124 instruction manual
Makita
Makita DHP458 instruction manual
Sparky Group
Sparky Group BR2 7.2Li HD Original instructions
