HP D7171A - NetServer - LPr User manual

configuration
Evolving
a higher
level of
protection
NetServer Rack ConfigurationHP
April 1999
Expanding Possibilities

2
1
2
3
4
5
6
7
8
Using the EIA total,
determine the rack size(s)
and quantity needed
Make a complete list of all
equipment to be rackmounted
Total the EIA units required for
all equipment*
Calculate the power
requirements* Identify the PDU(s) and cord sets required
Identify the amount of
ballast recommended
Identify sizes and quantity
from chosen rack line
Identify additional items:
• Rack delivery services
• Front doors
• Tie kits
• Side panel kits
• Switchboxes
• Rackmount kits
• Accessories
Calculate the total
equipment weight*
Choose the /E or /U
rack line
Choose additional items to
complete your rack solution
Selection list is complete —
place order
* See Calculation Configuration Table — page 15
Fill in the selection list on
the following page with items
identified in this shaded area.
Product information is also available at:
NetServer Rack Configuration Guide
This configuration guide is
intended to allow you to:
■Calculate the power
requirements, weight and
stability of your rack solution
■Determine the number of
racks required to rackmount
your equipment
■Identify the key features of
racks and accessory products
■Generate a complete custom
list of rack and accessories
required
HP strongly recommends the
use of the HP NetServer Rack
Assistant configuration software
to configure your rack solution.
This free tool is available from
the world wide web at
http://www.hp.com/go/netserver
If, for any reason, you are not able to use the Rack Assistant software,
follow the steps below to create your custom rack solution. For details
of each step, see the Configuration Details on pages 12 and 13.
http://www.hp.com/go/enclosures

3
Rack System Selection List for NetServers
Description Product Number Quantity For details, see page
HP Rack System Model HP Rack System/E41 J1500A ______ 4
HP Rack System/E33 J1501A ______ 4
HP Rack System/E25 J1502A ______ 4
HP Rack System/U33 J1466A ______ 5
HP Rack System/U25 J1464A ______ 5
Delivery Services Inside delivery service J1543A ______ 4
Coordinated shipment service J1544A ______ 5
Front Doors Front door for /E41 J1509A ______ 6
Front door for /E33 or /U33 J1510A ______ 6
Front door for /E25 or /U25 J1511A ______ 6
Tie Kits Tie Kit for /E41 J1512A ______ 6
Tie Kit for /E33 or /U33 J1513A ______ 6
Side Panel Kits Side panel kit for /E41 J1506A ______ 6
Side panel kit for /E33 J1507A ______ 6
Side panel kit for /E25 J1508A ______ 6
Power Distribution
PDUs 100-240V, 10 amps E7670A ______ 7
100-240V, 16 amps E7671A ______ 7
Bundle (1 ea. E7670A, E7671A, E7742A) E7672A ______ 7
100-240V, 16 amps E7674A ______ 7
100-127V, 16 amps E7675A ______ 7
100-240V, 16 amps E7676A ______ 7
Cord Sets 100-127V NEMA (to wall), C19 to 5-20P E7802A ______ 7
200-240V IEC (to wall or UPS), C19 to L6-20P E7803A ______ 7
100-240V IEC (toserver,storageorUPS) , C19 to C20 E7804A ______ 7
200-240V IEC (to UPS), C19 to L6-30P E7805A ______ 7
100-240V (to wall or UPS), C19 to unterminated E7806A ______ 7
250V IEC for LX Pro/Lxe Pro E7807A ______ 7
(to server, storage or UPS), C14 to C15
240V IEC (to European wall), C19 to IEC309 E7808A ______ 7
240V IEC (to European wall), C19 to CEE7/7 E7809A ______ 7
240V IEC (to server, storage or UPS) , C13 to C14 E7742A ______ 7
127V NEMA (to server, storage or UPS) , E7743A ______ 7
C13 to 5-15P
240V IEC (to server, storage or UPS) E7798A ______ 7
Switchboxes 4-port switchbox, plus 4 cable sets J1493B ______ 9
8-port switchbox, plus 8 cable sets J1497B ______ 9
Rackmount Kits
Universal Keyboard rackmount kit J1518A ______ 8
Monitor rackmount kit J1519A ______ 8
Plain shelf rackmount kit J1520A ______ 8
Servers NetServer LXr Pro Conversion Kit* J1523A ______ 9
NetServer LX/LXe J1455B ______ 9
NetServer LCII J1456B ______ 9
NetServer E J1496C ______ 9
Rackmount kit included with product
NetServer LH 3r Included
NetServer LXr Pro and LXr Pro8 Included
Storage NetServer Storage System/6 J1492B ______ 9
Rackmount kit included with product
NetServer Storage System/8 Included or C2788B* ______ 9
HP SureStore DLT Library 4115r and 4215r Included
Accessories Computer rails C2788B ______ 9
Ballast C2790A ______ 10
Filler panels (qty 6) J1514A ______ 10
Cable guide (qty 2) E7723B ______ 10
Mounting hardware J1522A ______ 11
Lift hooks (qty 4) J1521A ______ 11
Rail spacers (qty 4) J1516A ______ 11
*Needed only to mount in Rack System/E or Rack System/U

4
HP Rack System/E
Advanced, full-featured rack for the most demanding rackmount
requirements. Electronic Industry Association (EIA) standard compliant.
HP Rack System/E
Product Numbers J1500A J1501A J1502A
EIA Units 41U 33U 25U
Caster rating 1000 lbs per caster 1000 lbs per caster 1000 lbs per caster
Color Top and rear door Quartz gray Quartz gray Quartz gray
Columns and base Slate gray Slate gray Slate gray
Weight Empty rack 73.5 kg (162 lbs) 69 kg (153 lbs) 65 kg (144 lbs)
Packaged 142.4 kg (314 lbs) 132.9 kg (293 lbs) 124.3 kg (274 lbs)
Rear door 13.2 kg (29 lbs) 12.7 kg (28 lbs) 8.6 kg (19 lbs)
Dimensions Rack ( w x d x h ) 23.5 in x 36.5 in x 77.5 in 23.5 in x 36.5 in x 63.5 in 23.5 in x 36.5 in x 49.5 in
Rack packaged 40 in x 48 in x 86.5 in 40 in x 48 in x 72.5 in 40 in x 48 in x 58.5 in
( w x d x h )
Delivery Services
J1543A Inside Delivery Service—Available in the US only
Provides for delivery of rack to the installation site at the specified shipping address and removal of
packaging materials upon customer’s request. Order one part number per rack. 1–2 week delivery time.
Key Features
■Extendible top allows for an
additional 8U of vertical space
to be added to an existing rack
■Optimum ventilation including
perforated rear door and fully
perforated top
■Ships and moves fully
integrated, up to 1800 lbs.
■Retractable anti-tip foot
extends from front or rear
■Numbered columns for easy
integration
■Available in three sizes:
41U, 33U, 25U
Use the Rack System/E when
you want:
■Maximum configuration
flexibility
■To mount equipment up to
2000 lbs.
■Optimum ventilation capacity
■Vertical extension capability
to an existing rack
■Optimum stability while
servicing slide-mounted
equipment
Features
1Fully perforated top
2Lockable perforated rear door,
63% airflow
3Numbered columns
(numbered from bottom to top)
4Bi-directional, retractable anti-tip foot
5Casters
6Leveling feet
7Solid base
Optional
8Modular side panels
9Lift hooks
10 Filler panels
11 Perforated front door, 63% airflow
12 Ballast

5
HP Rack System/U
HP Rack System/U
Utility rack for basic rackmounting needs.
Electronic Industry Association (EIA) standard compliant.
Key Features
■Ships and moves fully integrated, up to 1000 lbs.
■Numbered columns for easy integration
■Adequate ventilation for NetServer systems
■One-piece removable side panels
■Perforated rear door, solid top
■Bolt-on anti-tip foot
■Available in two sizes: 33U, 25U
Use the Rack System/U when you want:
■Basic rack features
■To mount equipment with no special
ventilation requirements
Features
1Solid top
2Lockable perforated rear door,
63% airflow
3Numbered columns
(numbered from bottom to top)
4Bolt-on anti-tip foot
5Side panels
6Casters
7Leveling feet
8Solid base
9Cable guide
Optional
10 Filler panels
11 Ballast
12 Perforated front door, 63% airflow
Product Numbers J1466A J1464A
EIA Units 33U 25U
Caster rating 225 lbs per caster 225 lbs per caster
Color Top cap, columns, side panels Quartz gray Quartz gray
and rear door
Weight Empty rack 101.2 kg (223 lbs ) 84.4 kg (186 lbs)
Packaged 116.6 kg (257 lbs) 108 kg (238 lbs)
Rear door 8.6 kg (19 lbs) 7.6 kg (16 lbs)
Side panels 17.2 kg (38 lbs) 12.7 kg (28 lbs)
Dimensions Rack ( w x d x h ) 23.4 in x 36.5 in x 63.2 in 23.4 in x 36.5 in x 49.2 in
Rack packaged ( w x d x h ) 40 in x 48 in x 72.5 in 40 in x 48 in x 58.5 in
J1544A Coordinated Shipment Delivery Service—Available in the US only
Provides for rack and accessories to arrive within a 3-day period of each other at the customer location.
Accessories will arrive boxed together in one shipment. Order one part number per order. 1–2 week delivery time.

6
Doors, Tie Kits and Side Panels
Front Doors
Key Features
■Perforated, 63% airflow
■Lockable latch for equipment
security
■All equipment is visible through
the perforations
■Mounting hardware included
Use a front door to:
■Secure equipment from
unwelcome access
■Provide a clean aesthetic finish
to the rack Product No. Use with
J1509A /E41
J1510A /E33 and /U33
J1511A /E25 and /U25
This tie kit can also be used to connect
the /E41 with either an /E33 or /U33.
Product No. Use with
J1512A /E41
J1513A /E33 and /U33
Tie Kits
Key Features
■Easily installed without
removing or turning off
rackmounted equipment
■Can connect racks of different
sizes together (41U and 33U)
■Can connect /E and /U racks
together
■Increases security of equipment
by reducing side access
■Mounting hardware included
Use a tie kit to:
■Connect two or more racks
together
Side Panels
Use only with the Rack System/E
Key Features
■Snap on/off design, requires no
tools for installation or removal
■Kits contain the panels needed
to cover both sides of the rack
■Only one side panel kit is
required for a tied together
rack configuration
Use side panels to:
■Gain easy side access just
where you need it. Security is
maintained if a front and rear
are installed
■Provide a finished clean look
to the rack solution
/E25 Side Panel Kit
Product No. Use with* Kit contains
J1506A /E41 Qty: 2 9U side panels, Qty: 8 8U side panels
J1507A /E33 Qty: 2 9U side panels, Qty: 6 8U side panels
J1508A /E25 Qty: 2 9U side panels, Qty: 4 8U side panels
* Side panels come standard with the Rack System/U
/E25 Side Panels Installed
Perforation Material
Tie Kit Contents
Front Doors

7
PDUs, Cords/Cables
Cords Sets
Modular Power
Distribution Units (PDUs)
Key Features
■Up to four PDUs per rack
■Mounting hardware included
■Can be mounted vertically
or horizontally on columns
Use a PDU to:
■Conveniently provide power
to rackmounted equipment
Product Voltage Max Outlets Inlets Certification
Number Current
E7670A 100-240 (Univ) 10 amps 10 IEC320 C13 1 IEC320 C14 UL, C-UL, TUV-R GS
E7671A 100-240 (Univ) 16 amps 6 IEC320 C13, 2 IEC320 C19 1 IEC320 C20 UL, C-UL, TUV-R GS
E7672A* 100-240 (Univ) 16 amps 16 IEC320 C13, 2 IEC320 C19 1 IEC320 C20 UL, C-UL, TUV-R GS
E7674A 100-240 (Univ) 16 amps 7 IEC320 C13, 1 IEC320 C19 1 IEC320 C20 UL, C-UL, TUV-R GS
E7675A†100-127 16 amps 9 NEMA 5-15R, 1 IEC320 C13 1 IEC320 C20 UL, C-UL
E7676A 100-240 (Univ) 16 amps 10 IEC320 C13 1 IEC320 C20 UL, C-UL, TUV-R GS
* E7672Aisabundledsetof1ea.E7670A,E7671AandE7742Ajumpercable.
†For110V environments, HPrecommendstheuseof theE7675APDUbecauseNetServersship with apowerjumpercablecompatiblewithE7675Areceptacles.
PDUs
E7672A ContentsE7675A Contents
5-15P L6-30P L6-20P C14 C20 No Plug
5-15R C14 C20C13 C19
Plugs
5-20P
Outlets Inlets
IEC309 CEE7/7
Product Type CordLength Plug Compatible
Number APCUPS **
E7802A 100-127V NEMA (to wall) 4.5m (177.2in) C19 to 5-20P NS2200RM3U
E7803A 200-240V IEC (to wall or UPS) 4.5m (177.2in) C19 to L6-20P NS3000RMT3U
E7804A 100-240V IEC (toserver, storage or UPS) 4.0m (157.5in) C19 to C20 NS2200RMI3U
E7805A 200-240V IEC (to UPS) 4.5m (177.2in) C19 to L6-30P —
E7806A 100-240V IEC (to wall or UPS) 4.5m (177.2in) C19 to unterminated —
E7807A 250V IEC for LX Pro/Lxe Pro (to server, storage or UPS) 0.76m (29.9in) C14 to C15 —
E7808A 240V IEC (to European wall) 4.5m (177.2in) C19 to IEC309 —
E7809A 240V IEC (to European wall) 4.5m (177.2in) C19 to CEE7/7 —
E7742A 240V IEC (to server, storage or UPS) 2.5m (98.4in) C13 to C14 —
E7743A 127V NEMA (to server, storage or UPS) 2.5m (98.4in) C13 to 5-15P —
E7798A 240V IEC (to server, storage or UPS) 2.5m (98.4in) C19 to C20 —
** APC UPS products are sold and supported by APC and APC resellers (not orderable from HP).

8
J1519A Installed in Rack
Monitor Rackmount Kit Contents
Product No. Use with Kit contains EIA Units
J1519A All HP Racks Monitor base, snap-in front bezel, 11
mounting hardware
Monitor Rackmount Kit
Key Features
■Snap-in design
■Easy installation
■Mounting hardware included
Use the monitor rackmount kit to:
■Mount a 14”–19”monitor within
a rack
Rackmount Kits
J1518A Installed in Rack Keyboard Rackmount Kit Contents
Product No. Use with Kit contains EIA Units
J1518A All HP Racks Keyboard kit assembly, 2
mounting hardware
Universal Rackmount Kits
Keyboard Rackmount Kit
Key Features
■Retracts into the rack when not
in use
■Easy installation
■Fits all standard keyboards
■Mounting hardware included
Use the keyboard kit to:
■Mount a keyboard and mouse
within a rack
Note: These kits do not include a
keyboard or mouse.
J1520A Installed in Rack Shelf Contents
Product No. Use with Kit contains EIA Units
J1520A All HP Racks Stationary shelf, 1
mounting hardware
Plain Shelf
Key Features
■Supports up to 68 kg (150 lbs)
■Easy installation
■Mounting hardware included
■Attractive quartz color
Use a shelf to:
■Provide a stationary surface in
a rack for products without
a custom rackmount kit.

9
Rackmount Kits, Switchboxes
J1493B Kit Contents
Product No. Description Use with Kit contains EIA Units
J1493B 4-port console All HP racks 4-port switchbox, 4 sets of mouse, keyboard, 1 unit – front mount;
switchbox and monitor cables and mounting hardware 0 unit – rear mount
J1497B 8-port console All HP racks 8-port switchbox, 8 sets of mouse, keyboard, 1 unit – front mount;
switchbox and monitor cables and mounting hardware 0 unit – rear mount
Switchboxes
Key Features
■Available in 4-port and 8-port
models
■Appropriate quantity of 3.66m
(12 ft) cable sets are included
■Software controlled
Use a switchbox to:
■Control multiple NetServers
from a single monitor,
keyboard and mouse
LH 3r Installed in Rack J1455B Rackmount Kit Contents
Product No. Use with Rackmounted server EIA Units
J1455B All HP Racks LX Pro/LXe Pro 14
J1456B All HP Racks LC II 14
J1496C All HP Racks E Series 11
J1523A Only for /E and /U line LXr Pro 7
Rackmount kit is bundled with server, no separate purchase necessary.
All HP Racks LH 3r 8
All HP Racks LXr Pro8 10
Server Rackmount Kits
Key Features
■Designed to custom fit the
server
■Mounting hardware included
■Easy installation
Use the server rackmount kit to:
■Mount a server in a rack
Storage Rackmount Kits
Key Features
■Designed to custom fit the
storage system
■Mounting hardware included
■Easy installation
Use the storage rackmount kit to:
■Mount a storage system in
a rack
Product No. Use with Rackmounted Storage System EIA Units
J1492B All HP Racks Storage System/6 11
C2788B Only for /E and /U line Storage System/8 3
Needed only to mount in Rack System /E or RackSystem /U
J1492B Contents
J1497B Kit Contents
C2788B Contents

10
Accessories
C2790A Installed in Rack
Product No. Use with Kit contains
C2790A All HP Racks 30 lb. steel ballast, mounting hardware
Ballast
Key Features
■Mounts easily to the rear
columns
■Mounting hardware included
Use ballast to:
■Provide an added measure
of stability for servicing
slide-mounted equipment.
Filler panels
Product No. Use with Kit contains EIA Units
J1514A /E and /U racks only 6 filler panels 1 EIA unit per filler panel
Filler Panels
Key Features
■Easy snap-in design
■Contemporary industrial design
■No mounting hardware required
Use filler panels to:
■Attractively cover unused rack
space.
Cable Guide
Product No. Use with Kit contains
E7723B All HP Racks 2 19” cable guides, mounting hardware
Cable Guide
Key Features
■Sturdy 16-gauge metal will
support heavy cables
■Mounts vertically or horizontally
on rear columns
■Quick and easy installation
Use a cable guide to:
■Organize routing of data and
power cables

11
Accessories (continued)
J1521A Installed on Rack
Product No. Use with Kit contains
J1521A Rack System/E only 4 lift hooks
Lift Hooks
Key Features
■Each hook can support 500 lbs.
■Easy installation
■No additional hardware required
Use lift hooks to:
■Lift a rack weighing up to
2000 lbs. for repositioning
Spacers
Product No. Use with Kit contains Use with old legacy products
J1516A Rack System /E 2 left spacers, J1496A NetServer E rackmount kit
and /U only 2 right spacers, J1492A NetServer SS/5 rackmount kit
mounting hardware J1456A NetServer LCII rackmount kit
Rail Spacers
The Rack System/E and /U design
includes a recess of 1/2 inch on
the inside mounting surface of
each column to support mounting
full-width products. Spacers are
used with old legacy rackmount
kits to fill the 1/2 inch recess gap.
Key Features
■Die-cast aluminum construction
■Mounting hardware included
Use spacers to:
■Accommodatelegacy rackmount
kitsin the HP Rack System/E and /U.
Product No. Use with Kit contains
J1522A All HP racks 10 Torx T25 decorative screws, 10 Torx T25
and rack non-decorative screws with lock washers, 20 U-type,
accessories sheet metal nuts
Hardware
Use extra hardware to:
■Keep extra mounting hardware
at hand
Lift Hooks
Hardware

12
4
1
2
3
5
Configuration Details
Generate a complete list of products to be rackmounted.
Don’t leave anything out. If you know you’ll be using more than 1 rack, list the items to be included in each rack.
Determine the EIA units required for all equipment.
Each rack has a specific amount of vertical mounting space which is measured in EIA units (1 EIA unit is equal to 1.75 inches or
45.44 mm). The rack title is indicative of this measurement (i.e., Rack System/E25 has 25 EIA units of vertical mounting space).
Using the Calculation Configuration table on page 15, list the EIA units required for each product listed in step 1.
If there is a product to be rackmounted not listed on page 15, rackmount it on a plain shelf. In this case, calculate the height of
the product into EIA units (1 = 1.75 in or 44.45 mm) and add 1 additional EIA unit for the height of the shelf. Add together the EIA
units required for your rack solution.
Determine the rack size(s) and quantity needed.
■Up to 25U: choose either the Rack System/E25 or the Rack System/U25
■26U to 33U: choose either the Rack System/E33 or Rack System/U33
■33U to 41U: choose the Rack System/E41
■More than 41U: any combination of the /E25, /E33, /E41 or /U25, /U33
(Note: You can mix and even tie-together, the /E and /U lines. However, these lines do not have the same look and the rack
solution aesthetics will be compromised.)
Note on multiple racks:
If multiple racks are required, you may want to connect them with a tie-together kit. Make sure to use the appropriate size
tie kit. A 33U tie kit can connect a 41U and a 33U together. No tie kit is available for a 25U rack.
Calculate the power requirements.
The PDU is a rackmounted power strip with multiple power receptacles. Rack components are plugged into PDU receptacles.
The number of components placed in a rack impacts the quantity of power distribution units required and is affected by:
■facility power voltage (100-120V or 200-240V)
■number of power receptacles needed
■mounted equipment current (Amperes)
1. Determine the facility power voltage that will be used.
2. Count the quantity of receptacles needed from the PDU(s). (The Rack Storage/8 and Rack Storage/12
requires 2 power receptacles)
3. Total the Amperes required for all components in each rack.
(use the Configuration Calculation table on page 15 for this information) The total amperes of devices plugged into a PDU
cannot exceed the 10A or 16A rating of the PDU. When the 10A PDU is plugged into the 16A PDU, the total current of the two
PDUs cannot exceed 16A. If the result is greater than the maximum PDU amperage, order an additional PDU. Amperage can
be determined using the following formula (For 110V current, use 104 as the adjusted voltage. For 208V current, use 180. For
230V current, use 198.)
Total Watts
Amps = ————————
Adjusted Voltage
See Configuration Calculation table on page 15 for watts.
4. Determine the PDU(s) and cord sets.
■Using the table on page 7, find the appropriate PDU which is determined by the voltage and number receptacles required for
the rack solution (per rack).
■A list of cord sets is also available on page 7. Choose the power cord with the appropriate plug attached (to choose the
correct plug, you must know the type of wall/UPS receptacle to be used).
■Jumper cables are not needed for rack-optimized products.
Note on multiple racks:
No power or calculations can be made between racks. Calculating total power requirements does not allow for cross
connecting power between racks. Cross connecting power between racks could pose a serious threat of injury to personnel
or damage to components.
Calculate the total equipment weight.
All racks come with an anti-tip foot for temporary servicing. Ballast offers additional security in case someone forgets to
use the anti-tip foot. The calculations below recommend the number of ballasts to buy to prevent tipping if all slide-mounted
products are extended at the same time.

13
6
7
8
A
B
C
D
a
b
c
d
1.25 ft
1 ft
M1M2
F
250 N or
56.25 lbs
@ max
height = 2 m
Center of Gravity
Configuration Details
Note: You may choose not to install ballast weights if only trained service personnel will perform service, if the anti-tip foot is
used during servicing or installation, and not more the one device is extended from the rack at any time.
If using ballast, fill in the selection list on page 3 with the calculated number of ballast required.
Stability: Weight is a consideration when stacking the rack. In general, place the heaviest devices near the bottom of the rack
for greatest stability and servicing. Put lighter devices and seldom accessed devices (such as monitors and rack-optimized
storage modules) near the top of the rack.
Choose between the /E or /U rack line.
Choose the Rack System/E if you answer ‘yes’ to any of the following questions:
■Will you need to ship rack integrated?
■Do you want the option to increase the rack space by 8U for future growth?
■Is the equipment to be mounted over 1000 lbs.?
■Do you want optimum stability while servicing slide-mounted equipment?
■Do you require between 33U and 41U of vertical mounting space in a single rack?
■Does your equipment require optimum ventilation?
If you did not answer ‘yes’ to ANY of the above questions, remember the /E line is a full-featured, premium line while the /U line
is a basic, utility rack line with limited configuration choices. See pages
4 and 5 for more differentiating details. Fill in the selection list on page 3 with the rack sizes and quantity.
Determine all additional items required.
When applicable, choose the appropriate size. (See the appropriate page for features.)
Fill in the Selection list on page 3 with the quantity of all additional items:
■Delivery services — pages 4 and 5 ■Cord sets — page 7
■Front doors — page 6 ■Switchboxes — page 7
■Tie kits — page 6 ■Rackmount kits — page 8
■Side panel kits (/E line only) — page 6 ■Accessories — pages 9–10
■PDUs — page 7
Double check your list.
Go back through your notes and make sure all quantities have been included into the selection list on page 3.
Congratulations! You’re now ready to place your order.
Weight and Balance Worksheet:
1. Total the weight of operator serviceable slide-mounted products:
M1 A =______lbs; B =______lbs; C =______lbs; D =______lbs; . . .
2. Totaltheweightofallfixedandtrainedservicepersonnelserviceableproducts:
M2 a =______lbs; b =______lbs; c =______lbs; d =______lbs; . . .
3. Calculate the moment for both totals (M1 and M2) from above:
Model M1 M2
1.25 m (A + B + C + D . . .) * 1.25 ft –45.4 ft-lbs + (a + b + c + d + . . .) * 1.00 ft
1.6 m (A + B + C + D . . .) * 1.25 ft –92.1 ft-lbs + (a + b + c + d + . . .) * 1.00 ft
1.96m (A + B + C + D . . .) * 1.25 ft –136.4 ft-lbs + (a + b + c + d + . . .) * 1.00 ft
M1=
Momentonrackwithalloperatorserviceableslide-mountedproductsextended.
M2= Momentofallfixedandtrainedpersonnelserviceableslide-mountedproductsandrack.
M2 momentcalculations assume a 1.00 ft center of gravity for installed products
If M1 is less than or equal to M2, no additional counter weight is needed.
If M1 is greater than M2, use the formulas below to determine the required counter weight.
Force (in lbs) = (M1 – M2) ft-lbs ÷2.46 ft = amount of force required @ 2.46 ft
X = Force (lbs) ÷30 lbs = number of C2790A 30 lbs ballast kits to install,
where “X” is rounded up to the next highest integer, e.g., 1.2 = 2 ballast kits.

14
B
C
Side Panels Side Panels
A
Rear Door
596.2 mm
(23.5 in)
521.0 mm
(20.5 in)
452.1 mm
(17.8 in)
465.1 mm
(18.3 in)
996.2 mm
(39.2 in)
609.6 mm
(24 in)
735.1 mm
(28.9 in)
595.6 mm
(23.4 in)
69.7 mm 145.2 mm
Top Cap
Top Frame
60.5 mm
B
C
Side Panel Side Panel
A
Rear Door
596.2 mm
(23.5 in)
521.0 mm
(20.5 in)
452.1 mm
(17.8 in)
465.1 mm
(18.3 in)
996.2 mm
(39.2 in)
609.6 mm
(24 in)
735.1 mm
(28.9 in)
595.6 mm
(23.4 in)
83.5 mm 145.2 mm
Top Cap
Top Frame
Rack System/E
Rack System/U
Rack Specifications
Front Rack View Side Rack View
Front Rack View Side Rack View
J1500A
A1961.1 mm (77.2 in)
B1824.7 mm (71.8 in)
C111.2 mm (4.4 in)
J1501A
A1605.5 mm (63.2 in)
B1469.1 mm (57.8 in)
C111.2 mm (4.4 in)
J1502A
A1249.9 mm (49.2 in)
B1113.5 mm (43.8 in)
C111.2 mm (4.4 in)
J1464A
A1250 mm (49.2 in)
B1140.5 mm (44.9 in)
C108.9 mm (4.3 in)
J1466A
A1605.3 mm (63.2 in)
B1496.1 mm (58.9 in)
C108.9 mm (4.3 in)

15
(1) Needed only when rackmounting in the Rack System/E or /U
NetServer Configuration Calculation Table
Product Description EIA Wt VA Watts Rackmount Kit
Number Units (lbs) Required*
Servers HP NetServer LH 3r 8 150 632 638 Included
HP NetServer LXr Pro8 10 170 980 989 Included
HP NetServer LXr Pro 7 90 450 446 J1523A(1)
HP NetServer LX Pro/LXe Pro 14 187 1455 1225 J1455B
HP NetServer LHII/LH Pro/LD Pro 11 70 715 735 J1491B
HP NetServer LCII 14 55 505 301 J1456B
HP NetServer E 11 32 245 172 J1496C
Storage D4902A Storage System/8 3 80.5 211 Included or C2788B(1)
D3604B Storage System/6 11 36 480 J1492B
C1556A, C1559A HP SureStore DAT24e, 24GB 3 4.8 6 —
C6280F HP SureStore Autoloader 418 5 41 214 —
HP SureStore DLT Mechanism (40e/70e) 3 14.6 50 C6287J
HP SureStore DLT Library 8 97 257 Included
UPS NS2200RM3U APC Smart-UPS 2200NS, 3 102 N/A 1600 Included
120V (Available only through APC)
NS2200RMI3U APC Smart-UPS 2200NS, 3 102 N/A 1600 Included
230V (Available only through APC)
NS3000RMI3U APC Smart-UPS 3000NS, 3 112 N/A 2250 Included
230V (Available only through APC)
NS3000RMT3U APC Smart-UPS 3000NS, 3 112 N/A 2250 Included
208V (Available only through APC)
Accessories Up to 19" Monitor 11 30 125 J1519A
Any Keyboard 2 10 — — J1518A
J1493A Switchbox 4-port 0 or 1 12 100 Included
J1497A Switchbox 8-port 0 or 1 12 100 Included
Hubs & Routers 28673A HP 10:10 LAN Bridge 1 6 96 48 Included
28682A HP Fiber-Optic Hub Plus 1 6 96 48 Included
28688B HP EtherTwist Hub Plus 1 6 96 48 Included
J2413A HP AdvanceStack 100VG Hub-7m 2 10 144 86 Included
J2415A HP AdvanceStack 100VG Hub-14 2 10 144 86 Included
J2601B HP AdvanceStack 10Base-T Hub-24 2 9 144 86 Included
J2611B HP AdvanceStack 10Base-T Hub-16U 1 5 48 24 Included
J2962A HP AdvanceStack Power Supply 3 22 1200 720 Included
J3100B HP AdvanceStack Switch 2000 7 20 360 216 Included
J3125A HP AdvanceStack Switch 200 1 10 96 48 Included
J3135A HP AdvanceStack 10Base-T Hub-16U Bundle 1 5 48 24 Included
J3175A HP AdvanceStack Switch 208 with 100BaseTX 2 6 192 115 Included
J3177A HP AdvanceStack Switch 224 with 100BaseTX 2 9 192 115 Included
J3200A HP AdvanceStack 10BT S Hub-12R 2 9 144 86 Included
J3201A HP AdvanceStack S Hub-12R w/Mgmt 2 9 144 86 Included
J3202A HP AdvanceStack 10BT S Hub-24R 2 9 144 86 Included
J3203A HP AdvanceStack S Hub-24R w/Mgmt 2 9 144 86 Included
J3204A HP AdvanceStack S Hub-24T 2 9 144 86 Included
J3205A HP AdvanceStack S Hub-24T 2 9 144 86 Included
J3231A HP Remote 2C and Internet Router Bundle 2 10 180 90 Included
J3245A HP AdvanceStack Switch 800T 2 10 190 101 Included
* Included = Rackmount kit is included with the equipment purchase;
— = no custom rackmount kit available, use a plain shelf (J1520A)

Expanding Possibilities
Technical information in this document
is subject to change without notice.
© Copyright Hewlett-Packard Company
1998. All Rights Reserved. Reproduction,
adaptation, or translation without prior
written permission is prohibited, except
as allowed under the copyright laws.
Update Information
Last Electronic Update —4/99
Last Printed Update —4/99
5968-0156E
Printed on recycled paper