HUBER+SUHNER EDR User manual

INSTALLATION
MANUAL
HUBER+SUHNER AG
Fiber Optics
Fiber Management Systems
DOC-0000772690 Rev A
Date: 20/12/2016
Page 1 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
EDR Flat Pack Assembly Instructions
Table of contents
•FITTING JACKING FEET AND CASTORS............................................................ 1
•MAIN FRAME ASSEMBLY (CENTRE POST ARRANGEMENT)........................... 3
•MAIN FRAME ASSEMBLY (4 POST ARRANGEMENT)........................................ 4
•MAIN FRAME ASSEMBLY (OFFSET POST ARRANGEMENT)........................... 5
•19″VERTICAL MOUNTING RAIL FITTING (600 WIDE CABINETS) .................... 6
•19″VERTICAL MOUNTING RAIL FITTING (800 WIDE CABINETS) .................... 7
•SIDE PANEL HINGE BUSH FITTING .................................................................... 8
•SIDE PANEL FITTING ............................................................................................ 9
•DOOR HINGE FITTING (ON CABINET) ..............................................................11
•DOOR FITTING.....................................................................................................11
•DOOR HANDING CHANGE PART 1.................................................................... 12
•DOOR HANDING CHANGE PART 2.................................................................... 13
•DOOR HANDING CHANGE PART 3.................................................................... 15
•DOOR HANDING CHANGE PART 4.................................................................... 16
•TOP PANEL FITTING ...........................................................................................17
•EARTH BONDING ................................................................................................18
•VERTICAL BAFFLES............................................................................................ 19
•TOP AND BOTTOM BAFFLES............................................................................. 21
FITTING JACKING FEET AND CASTORS
Step 1
If Jacking feet and Castors are required it is advised that
they are fitted prior to assembling the frame.
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 2 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
Step 2
Fit the 2 stiffening blocks.
The 10mm block on the bottom (orange arrow) and the
5mm block on the top (blue arrow) secure using 2x M6
universal screws
Next screw in the jacking foot so that it is below the castor
level allowing the castor to roll freely when the cabinet is
assembled.
Step 3
Push the castor bolt through the hole in the mounting plate
and secure using the M12 nut and washer.
Repeat for all remaining castors.
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 3 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
MAIN FRAME ASSEMBLY (CENTRE POST ARRANGEMENT)
Step 4
Base Frame
Fit the pre-assembled base frame to the 4
Vertical aluminium extrusions (Posts) using
4 off M8X95mm Taptite Screws supplied.
Butt 2 of the posts together and position
them centrally with the dual groove inner-
most.
Step 5
Top Frame
Fit the pre-assembled top frame to the 4
Vertical aluminium extrusions (Posts) using
4 off M8X95mm Taptite Screws supplied.
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 4 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
MAIN FRAME ASSEMBLY (4 POST ARRANGEMENT)
Step 6
Base Frame
Fit the pre-assembled base frame to the 4
Vertical aluminium extrusions (Posts) using 4
off M8X95mm Taptite Screws supplied. Ar-
ranging the posts in each corner with the dual
groove innermost.
Step 7
Top Frame
Fit the pre-assembled top frame to the 4
Vertical aluminium extrusions (Posts) using 4
off M8X95mm Taptite Screws supplied
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 5 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
MAIN FRAME ASSEMBLY (OFFSET POST ARRANGEMENT)
Step 8
Base Frame
Fit the pre-assembled base frame to the 4
Vertical aluminium extrusions (Posts) using 4
off M8X95mm Taptite Screws supplied. Fit 2
posts in either corner (These will form the rear
of the cabinet upon completion see red ar-
row). Fit 2 posts in the mid position using the
hole furthest away from the previously fitted
rear posts (blue arrow).
Note adapter channels removed for clarity
Step 9
Top Frame
Fit the pre-assembled top frame to the 4
Vertical aluminium extrusions (Posts) using 4
off M8X95mm Taptite Screws supplied.
Note adapter channels removed for clarity
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 6 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
19″VERTICAL MOUNTING RAIL FITTING (600 WIDE CABINETS)
Step 10
When fitting the Vertical Mounting Rails
(VMR) within a 600 wide cabinet it is neces-
sary to bolt them straight to the side extru-
sions which is fitted with graduated tapes.
Fit 1xM6 Slide nut into groove nearest gradu-
ated tape (Slide nuts can be fitted without the
need to remove the end cover’s)
Step 11
Position the VMR distance notch so that that it
reads approx.128mm on the graduated tape.
Now take one of the adjustable handles +
2xM6 washers and screw into place (Note
that it is necessary to push in the red button
or pull back the handle to disengage the in-
ternal spline thus allowing free rotation of the
handle which will allow the thread to be
screwed in.
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 7 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
19″VERTICAL MOUNTING RAIL FITTING (800 WIDE CABINETS)
Step 12
When fitting the Vertical Mounting Rails
(VMR) within a 800 wide cabinet it may be
necessary (if not already fitted) to first fit 4 x
VMR support channels 2 on the top frame 2
on the bottom frame by bolting them straight
to the side extrusions which is fitted with
graduated tapes fitted.
Step 13
Fit 1xM6 Slide nut into groove nearest gradu-
ated tape (Slide nuts can be fitted without the
need to remove the end cover’s).
Offer up the VMR support channel making
sure that the position notch is pointing at the
desired distance from the front and rear
(128mm approx.) Note the Channel support
has 2 slots these need to be facing outwards
(see arrows).
Now take one of the adjustable handles +
2xM6 washers and screw into place (note that
it is necessary to push in the red button or pull
back the handle to disengage the internal
spline thus allowing free rotation of the handle
which will allow the thread to be screwed in.
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 8 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
Step 14
Now fit the 4 x VMR’s using 2x M6 universal
screws + 2x serrated flange nuts (top and
bottom)
NOTE Position of front screw shown on the
left rail this will set the rails up in the 19” con-
figuration
SIDE PANEL HINGE BUSH FITTING
Step 15
Should the side panel bushes need to be
Fitted they will need arranging as shown and
screwed down with M5x10 Pozi drive screws
Step 16
For centre post arrangements the single hole
bush indicated with the blue arrow is orientat-
ed with the slotted hole facing outermost as
indicated by the yellow arrows with leading
edge touching the extrusion cap
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 9 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
Step 17
For four post arrangements the single hole
bushes indicated by the blue arrow are fitted
in the centre of the side extrusion equi-distant
from the ends with the slotted holes facing
innermost.
Step 18
For the offset post arrangement the bushes
follow an alternating pattern as shown by the
arrows. With the single hole bushes facing
forward as indicated by the yellow arrow.
SIDE PANEL FITTING
Step 19
When fitting the side panels it is necessary to
first pull the hinge pins back and lock them off
on the notch provided
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 10 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
Step 20
Now offer up the panel so that the pins line up
with the side panel bush holes and release
the pin. The pins should slide into the hole
allowing it to swing
Step 21
Swing the panel into its final location with the
remaining pins over the holes in the side pan-
el bushes and release the pins.
The panel should now be fixed in place
Step 22
Repeat for all remaining side panels
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 11 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
DOOR HINGE FITTING (ON CABINET)
Step 23
Should the hinges need fitting this can be
easily done by removing the snap off section
of the extrusion cover to expose the screw
thread locations in the extrusion end cover
shown
Step 24
Once this has been done the hinge can be
offered up to the extrusion and screwed into
place as shown
Repeat steps above to fit lower hinge.
Note:
Doors are usually assembled with the hinge
on the lefthand side (when facing the cabinet)
DOOR FITTING
Step 25
The door is easily fitted to the cabinet using
the two retracted hinge pins at each Hinge.
Simply pull the upper and lower pin out on the
hinge Upper hinge shown.
Repeat for lower hinge.
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 12 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
Step 26
Offer up the door to the cabinet, locating the
hinge pins over the opposite part of the hinge
which is fitted to the cabinet.
Once in place push on the hinge pins until
they snap into their closed position.
The door should now hang correctly.
DOOR HANDING CHANGE PART 1
Step 27
To change the door handing.
Simply support the weight of the door, pull the
upper and lower pin out on the hinge.
Repeat for lower hinge
The door can now be removed and placed to
one side till later.
Step 28
Now remove the hinges on the cabinets by
undoing the 2 screws. (Upper & Lower)
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 13 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
Step 29
On the opposite corner extrusions it will be
necessary to remove the snap off section of
the extrusion cover to expose the screw
thread locations in the extrusion (top cover
shown).
Step 30
Once this has been done the hinge can be
offered up to the extrusion and screwed into
place as shown.
Repeat steps above to fit lower hinge
DOOR HANDING CHANGE PART 2
Step 31
The door can now be hung on the opposite side by rotating it through 180°.
Note:
The door handle will be upside down and will need to be removed and reinstalled.
To remove the door handle first release the upper lock rod:
Depress the 2 levers on the lock rod guides pulling the lock rod in the direction shown by the blue arrow
(Starting with the upper block and then the lower block)
Once the lock rod has been released pull the lock rod forward to align the square head of the fixing pin
with the hole in the lock rod now uncouple the lock rod.
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 14 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 15 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
DOOR HANDING CHANGE PART 3
Step 32
Now unscrew the 3 screws on the back of the locking gearbox.
Drop the gearbox forward to align the square head of the fixing pin with the hole in the lower lock rod.
Now uncouple from the lock rod.
The handle will now release by tipping forward from the top.
Rotate the handle through 180° so that it will function correctly with the door in the opposite handing.
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 16 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
DOOR HANDING CHANGE PART 4
Step 33
Now couple the lower lock rod by aligning the square head of the fixing pin of the gearbox with the hole in
the lower lock rod.
Drop the gearbox forward to connect the handle to the gearbox and screw the 3 screws on the back of the
locking gearbox to secure the gearbox to the handle.
Now couple the upper lock rod by aligning the square head of the fixing pin of the gearbox with the hole in
the upper lock rod.
Swing the upper lock rod forward so that it depresses the tabs on the lock rod guides and push the upper
lock rod in the direction of the blue arrow till the tabs click back holding the rod in place.
The door can now be fitted as described.
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 17 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
TOP PANEL FITTING
Step 34
To fit the top panels place the first panel in the
aperture at the top of the cabinet and slide it
to the front or rear of the top frame.
Step 35
Now fit the second panel behind the first.
Step 36
And finally fit the last panel in the remaining
space.
Secure all the panels using the M6X12
screws.
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 18 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
EARTH BONDING
Step 37
Fit 2 x M6 slide nuts to the slots in the side
extrusion
Step 38
Then screw the bracket to the side extrusion
using 2 x M6x12 screws
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 19 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
Step 39
Connect the side panels, doors and vertical
mounting rails to the earth bracket
Using the earth points indicated and the burst
outs on the lower end of the vertical mounts
VERTICAL BAFFLES
Step 40
To fit vertical baffles to the cabinet first fit 2 x slide nuts into the grove in the top and bottom side extru-
sions.
Now offer up the baffle plate so that the fixing holes line up with those in the slide nuts
Take one of the adjustable handles + 2xM6 washers and screw into place (note that it is necessary to
push in the red button or pull back the handle to disengage the internal spline thus allowing free rotation of
the handle which will allow the thread to be screwed in.
Fully compliant
Slide the baffle towards the 19” vertical mounting rail until the brush is touching then fully tighten the ad-
justable handle to secure.
Repeat for the upper fixing.
Repeat all steps above to fit other vertical baffle.
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.

INSTALLATION MANUAL
EDR Flat Pack Assembly Instructions
Page 20 of 21
HUBER+SUHNER disclaims any liability resulting from incorrect installation and use, including any damages resulting from the use of tools and
accessories other than the ones recommended herein. Any installation performed by unqualified personnel voids the product warranty provided by
HUBER+SUHNER. All due care and attention must be exercised when performing the installation of these products. For advice concerning the
general handling of these products please contact HUBER+SUHNER.
This document is downloaded via www.farbin.ir as an authorized distributer in IRAN.