Hunter M3633-01 User manual

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
PAGE
16
PAGE
5
PAGE
6
30 inches
7 feet
PAGE
2
What to Expect with
Your Installation Ceiling Bracket
Ladder
PAGE
3
Tools Needed
Maintenance
& Cleaning
Blades Troubleshooting
PAGE
9
PAGE
12
WiringDownrod
Bulbs & Globe
Blade Irons
Table of Contents
Canopy
PAGE
14
PAGE
15
PAGE
4
Mounting Options
PAGE
20
?
?
?
PAGE
21
Congratulations on purchasing your new
Hunter® ceiling fan! It will provide comfort and
performance in your home or ofce for many
years. This installation and operation manual
contains complete instructions for installing
and operating your fan.
We are proud of our work and appreciate the
opportunity to supply you with the best ceiling
fan available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
PAGE
7
Light Kit
PAGE
17
Remote & Cradle
1
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

2
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company
Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
What to Expect with Your Installation
Know your wiring
If you are unfamiliar
with wiring, use a
qualied electrician.
You may need a
friend to help you.
Check box to see
fan weight
Assess location
76.2 cm /
30 in.
from blade tip
to nearest wall
or obstruction
2.1 m /
7 ft.
from bottom
edge of blade
to the oor
Select a downrod length
Assess ceiling angle
Must be able to
secure the fan to
building structure or
fan-rated outlet box
1
2
3
Standard Downrod
(included, pre-assembled)
for ceilings 2.4–3 meters /
8–10 feet high
Shorter Downrod
(included)
for fans installed close to ceiling
Longer Downrod
(sold separately)
for ceilings 3 meters / 10 feet or
higher
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
w.1 - To reduce the risk of re, electrical shock, or personal injury, mount
fan directly from building structure and/or an outlet box marked
acceptable for fan support of 70 lbs (31.8 kg) and use the mounting
screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your
fan, disconnect the power by turning off the circuit breakers to the outlet
box and associated wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent warning device,
such as a tag, to the service panel.
w.3 - To reduce the risk of re, electrical shock, or motor damage, use only
Hunter Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade brackets
when installing the blade brackets, balancing the blades, or cleaning the
fan. Do not insert foreign objects in between rotating fan blades.
c.1 - All wiring must be in accordance with national and local electrical
codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualied
electrician.
c.2 - Use only Hunter replacement parts.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: modications not approved by the party responsible for
compliance could void user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
CAUTIONS

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Tools Needed
Ladder
Power Drill
(optional)
9/64” Drill Bit
(optional)
Screwdrivers
Pliers Wire Strippers
If mounting to a support structure, you will also need these tools.
Do not discard the hardware bags or mix
parts from different bags. Make note of
the symbol printed on each hardware
bag. The symbols can be used to identify
the appropriate hardware for each step.
3
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

4
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company
Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
If you have an angled ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Guide Touches
BOTH Ceiling & Wall
S
I
T
U
A
T
I
O
N
1
Guide Touches Wall
but NOT Ceiling
S
I
T
U
A
T
I
O
N
2
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
You need ONLY
a Longer
Downrod
*most common
If you have a at ceiling:
Hang your fan by a standard downrod (included).
Mounting Options
Use Standard Mounting
or Low-Prole Mounting
to hang the fan from a at ceiling.
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
34OCEILING
WALL
OPTION
1
Standard
Mounting
OPTION 2
Angled
Mounting
2 3
SLIDE
toward ceiling
PLACE
against wall
1
FOLD
on dotted line
34°
Use the three steps below to determine if your ceiling angle is greater than 34°
Support
Structure
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
Standard
Mounting
Style
Support
Structure
Ceiling
Outlet Box
(required)

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Ceiling Bracket
Refer to warning w.1 on pg. 2
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
For angled ceilings, point
opening toward peak.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Make sure all four bumpers are
still attached.
Use wood screws
(included) when securing
to support structure with
approved electrical outlet
box. Drill 9/64” pilot holes
in support structure to aid
in securing ceiling bracket
with hardware found in
the hardware bag.
Use machine screws
(provided with outlet
box) when securing to
existing ceiling fan-rated
outlet box. Make sure
it is securely installed
and is acceptable for fan
support of 31.8 kg (70 lbs)
or less.
OFF
Turn Power
5
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Blade Irons
Turn the motor assembly upside down and
place it in one of the holes in the packaging.
Install a blade iron to the blade iron mounting
plate using two blade iron assembly screws,
found in the hardware bag. Repeat this
process to install all ve blade irons.
6
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Feed the 9-pin plug connector coming from
the bottom of the motor housing through
the center hole in the light kit assembly.
Connect it to the plug connector found
in the switch housing area of the light kit
assembly. Make sure to line up the colored
markings on the connectors.
Partially install two light kit assembly
screws, found in the hardware bag,
halfway into the motor housing as
shown. It does not matter which two
screw holes you choose.
Align the keyhole slots in the top of
the light kit assembly with the partially
installed assembly screws. Wrap the
keyhole slots around the screws and
twist counterclockwise.
Light Kit
Light Kit
Assembly
Screw
7
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Light Kit (continued)
Make sure the light kit assembly is securely attached to the
motor housing. Failure to properly secure all three assembly
screws could result in the light xture falling.
Insert a third light kit assembly screw,
found in the hardware bag, into place
and tighten all three screws securely.
Carefully push all switch housing
components into the switch housing,
then install the switch housing plate
using two light kit assembly screws,
found in the hardware bag.
8
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Downrod
Slide
Slide
1 2 3 4 5
678910
Sold Separately
Included
Shorter
Downrod
for fans installed
close to ceiling
Option 1Option 2
Option 3
skip to next page
If you need a different downrod length follow these steps:
Steps 1–5 to remove standard downrod pipe
Steps 6–10 to reassemble with new pipe
Included (pre-assembled)
Longer
Downrod
for angled ceilings
or ceilings 3 m /
10 ft. or higher
Standard
Downrod
for ceilings 2.4–3 m /
8–10 ft. high
9
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
KEEP!
Remove the pre-installed
setscrew so that the downrod
can be inserted.
Hand tighten the downrod (at
least 4–5 full turns) until it stops.
Downrod (continued)
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
If the setscrew is not tightened
securely, the fan may fall.
K
E
E
P
!
The wires can be cut, but
leave at least 20 cm / 8 in.
extending from the top of
the downrod.
8 in.
3/8 in.
C
U
T
&
S
T
R
I
P
(not to scale)
.95 cm
3/8 in.
20 cm
8 in.
20 cm / 8 in. .95 cm
3/8 in.
1010
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Downrod (continued)
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
11
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Wiring
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
F
R
O
M
C
E
I
L
I
N
G
F
R
O
M
C
E
I
L
I
N
G
B
R
A
C
K
E
T
green/yellow stripe (grounding)
green/yellow stripe
green/yellow stripe
Note: To connect the wires, hold
the bare metal leads together and
place a wire connector over them,
then twist clockwise until tight.
Using an orange wire connector
from the hardware bag:
Connect the 3 grounding wires
(green, green/yellow stripe, or bare
copper) coming from the ceiling,
downrod, and ceiling bracket.
F
R
O
M
F
A
N
Receiver
Place the receiver on top of the
downrod assembly as shown.
12
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Wiring (continued)
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
Note: If you have a dual switch,
please cap the secondary power
wire from the ceiling. This will
result in one unused switch.
Note: The Avia ceiling fan is
designed to be operated by the
included remote. Keep your
switches in the “On” position to
ensure proper functionality.
Using the orange wire connectors
from the hardware bag:
• Connect the black (ungrounded)
wire from the ceiling to the black
wire from the receiver.
• Connect the white (grounded)
wire from the ceiling to both the
white wire from the receiver and
the white wire from the fan.
F
R
O
M
R
E
C
E
I
V
E
R
black blue
yellow blue
Using the orange wire connectors
from the remote control hardware bag:
• Connect the yellow wire from
the receiver to the black wire
from the fan.
• Connect the blue wire from the
receiver to the blue wire (or
possibly black with white stripe
wire) from the fan.
F
R
O
M
F
A
N
F
R
O
M
R
E
C
E
I
V
E
R
F
R
O
M
C
E
I
L
I
N
G
black (ungrounded) white (grounded)
black white
F
R
O
M
F
A
N
white
13
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Canopy
Lift the canopy into place so that
the screw holes are aligned.
Position the canopy so that, when
lifted into place, the canopy ts into
the hanging bracket as shown.
Screw
Holes
Insert the two canopy screws
found in the hardware bag.
14
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Blades
Put each blade washer, found in
the hardware bag, onto a blade screw,
found in the hardware bag. Then secure
each blade to a blade iron using the blade
screws and washers.
15
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Bulbs & Globe
Carefully lift the globe up inside
the light xture as far as it will go.
Rotate the globe in a clockwise
direction until it is held tightly in
place by the three tabs.
Position the notches in the
outer rim of the globe so they
line up with the tabs on the
light kit assembly.
Install a bulb into each of the
sockets. When necessary, replace
with bulbs of the same wattage.
Notch
Tab
CONGRATULATIONS!
YOU’RE DONE!
See next page for fan
operation instructions.
16
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Remote & Cradle
ON
Turn Power
CAUTION:
• Always purchase the correct
size and grade of battery most
suitable for the intended use.
• Replace all batteries of a set at
the same time.
• Clean the battery contacts and
also those of the device prior to
battery installation.
• Ensure the batteries are
installed correctly with regard to
polarity (+ and -).
• Remove batteries from equipment
which is not to be used for an
extended period of time.
• Remove used batteries promptly.
17
To access the battery compartment,
remove the small Phillips head screw
that secures the battery door to the
transmitter assembly.
Phillips
Head
Screw
Battery
Door
Install two AAA batteries, found in the
remote control hardware bag, into the
transmitter. Clean the battery contacts prior
to installing the batteries. Please contact
your local battery recycling center for proper
battery disposal information.
17
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Remote & Cradle (continued)
Quickly press the Light button to turn
the lights off and on. Hold the Light
button to raise and dim the light level.
Dimming Mode: To enable dimming,
your remote must be set to Dimming
Mode. To toggle Dimming Mode on
or off, long press the “Fan Speed Up”
button and “Fan Speed Down” button.
The Fan On/Off button turns the fan
on or off. Adjust the fan speed using
the “Fan Speed Up” or “Fan Speed
Down” directional buttons.
Fan Speed Up
Fan Speed
Down
Fan On/Off
Light On/Off
The remote transmitter is already paired to the
receiver and ready to use.
Note: If your need to pair your remote, turn fan
power off and back on at the wall switch. Within 3
minutes, press and hold both the Fan Off button
and the High button for 4 seconds to pair the
remote. To prevent faulty operation, please
ensure all other ceiling fans within range are
turned off at the wall switch while pairing.
18
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Option 1: Using Screws
Option 2: Using Adhesive Strip
Install the cradle bracket to the wall with
the included screws.
You have two options to install the included remote control cradle
to the wall. Choose which path works best for you.
Choose your cradle installation location.
If you are installing into drywall, drill two
9/64 width holes using the cradle bracket
as a guide. Gently hammer the included
drywall anchors into the pre-drilled holes. Press the cradle bracket
against the wall and hold
rmly for 30 seconds.
Slide the cradle onto the
mounted bracket.
Remove the cradle from
the cradle bracket.
Apply the adhesive sticker
to the back of cradle
bracket per the instructions
on the adhesive sticker.
Remote & Cradle (continued)
19
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company

Monday - Friday 8am - 6pm CST
Saturday 11am - 4pm CST
(English or Español) 1.888.830.1326
www.HunterFan.com
Operation, Maintenance, & Cleaning
For cleaning the fan, use soft brushes or
cloths to prevent scratching. Cleaning
products may damage the nishes.
Reverse
Switch
To switch the direction of air ow, move
the reverse switch to the opposite
position. You will need to remove the
light kit glass to do so.
Slide the remote into the cradle
when not in use.
20
M3633-01 • 01/03/17 • © 2017 Hunter Fan Company