Husky EZ WIRE User manual

EZ WIRE INSTALLATION INSTRUCTIONS
1

INSTALLATION RECOMMENDATIONS
Tools Recommended:
•Safety ladder (most jobs too tall to rea h from floor)
•Carpenter Level
•Chalk line
Tools Required
•1/2” Masonry bit (drill holes in floor for post)
•1/2” wren h or so ket (s rews for door to the post)
•¾” wren h or so ket (for an hor bolts)
•Small hammer (to insert drive pins)
Parts Recommended:
•
Floor An hors (part #H5814 in post kit. ½” x 4
-
1/4”) Post Shims (Part #H5820 in post kit) INCLUDED
2
•
Floor An hors (part #H5814 in post kit. ½” x 4
-
1/4”) Post Shims (Part #H5820 in post kit) INCLUDED
•Drill Bits (various)
•Tape measure
•Safety Items (hardhat, gloves, safety glasses & steel toe work shoes); remove jewelry
Prior to installation:
•Prior to beginning installation please he k bill of lading to make sure that you have all the parts required for the assembly
•Make sure that the installation area is lear of all obstru tions
•Read thoroughly all the instru tions pertinent to your installation
•The following installation instru tions should be used as a guide for installing Husky Ra k & Wire EZ WIRE produ ts. Good ommon
sense and appropriate safety pre autions must be used during installations. The produ t may be unstable during installation;
temporary bra ing should be used until all hardware is tightened and the produ t is properly an hored to the floor. Permanent field
bra ing (NOT SUPPLIED) may be installed. Call Fa tory if installation help is needed. Installation problems arising from job site
onditions should be referred to a professional installer. Refer produ t assembly questions to Husky Ra k & Wire. 800-438-5629.
•DO NOT CLIMB FENCE DURING OR FTER INST LL TION

PANEL/POST ARRANGEMENTS
•Use a halk-line to mark the partition
runs on the floor.
•Starting with a Line Post, lag the post
to the floor using two floor an hors.
(the line post is 2 ½” square tube
with 2 ½” x 7 ½” footplate welded to
it). Make sure the slots are fa ing
inside of the age.
inside of the age.
•Stand up another Line post at a
distan e of width of the panel to be
installed. (Distan e between in the
post = Nominal width of the Panel – 2
3/8”). For 8’ panel, distan e between
the post is 96”-2 3/8” = 93 5/8”
•Pi k up the panel and install the
hooks in the slots of the line post.
Install bottom panel first.
•Install top panel and fasten to the
post using drive pins.
3
•EZ Wire panels are installed from the inside of the cage.

PANEL/POST ARRANGEMENTS
•Install one drive pin per
hook for maximum
se urity.
•
Put drive pin into the
Put drive pin into the
hole
•Tap on the extended pin
using hammer until it is
flush with the ap part
of the drive pin.
DRIVE
PIN
Inside of
the age
4

CORNER POST APPLICATION
•Corner post are used for
turning orner at 90
degrees.
•
Corner post an be
Corner post an be
installed as an Inside
Corner or Outside
Corner.
Inside
Corner 5

SINGLE SWING DOOR
•Swing doors an be installed Left/Right Hand,
Swing In or Swing Out.
•The Pi ture shows Hinge right Swing Out
(HRSO) door looking from outside of the
age.
•The opening between the posts for a swing
door installation is equal to Nominal Width –
2 3/8”. (For example for 3’ door the opening
between the post is 36-2 3/8” = 33 5/8”)
•
Install Transom panel first and an hor the
Transom Panel
Strike
•
Install Transom panel first and an hor the
line posts to the floor ensuring the opening
width at the floor equals the transom width.
•Using 5/16” x 3” Carriage Bolts (3), atta h
door and strike bar to the posts.
•Install Cylinder Lo k (see page…).
Strike
Bar
6

DOUBLE SWING DOOR
•First install header bar on top
using 5/16” x 3” long arriage
bolts.
•Install door panels to the post
using 5/16” x 3” long arriage
bolts. Make sure the ane bolt
is inside of the age
HEADER BAR
is inside of the age
OPERATION: Close the door panel
with the ane bolt first against
the header bar and then turn
the ane bolt handle. The rod
will go behind the header bar
and will se ure the door in
pla e. Close the door panel
with lo k plate against the
other door panel.
7

SINGLE SLIDE DOOR
•Slide doors an be installed inside or outside .
•The inside distan e between the posts is measuring
width of the door – 2 ½”. (If a panel is installed
above the door, the opening between the posts will
be the width of the panel)
•Install lo k in the door first.
•Atta h two 4-wheel trolley per door in the ½”
diameter holes provided.
•Using 5/16” x 3” arriage bolts and nuts, install
Lat h Re eiver and Bottom Slam.
•
Install the Tra k Bra ket to the post on either side of
TRACK
BRACKET
OVERHEAD
TRACK
•
Install the Tra k Bra ket to the post on either side of
the door opening using 5/16” x 3 ½” arriage bolts
and nuts. A third Tra k bra ket an be installed on
the post or to the panel using Panel Kit Plate.
•Install the Door Tra k in the Tra k Bra kets. Se ure
the Tra k by tightening ¼” s rew provided.
•Slide the door trolleys into the overhead Tra k.
•Install a tra k bumper as a keeper for the door
Trolleys.
•Atta h the Bottom Guide as shown.
LATCH
RECEIVER
BOTTOM SLAM
BOTTOM
GUIDE
8

SINGLE SLIDE DOOR
SLIDE LOCK BOTTOM SLAM BOTTOM GUIDE
LATCH RECEIVER TRACK BRACKET 4-WHEEL TROLLEY
9

SINGLE SLIDE DOOR
•If the tra k is not long
enough to rea h the
next post, Panel Kit
Plate with Hardware is
supplied to atta h tra k
Tra k
hanger
supplied to atta h tra k
hanger to the panel.
10
Panel Kit
Plate with
Hardware