Huvema HU 50 GC-4 TOPLINE User manual

HU 50 GC4 TOPLINE
INDUSTRIAL DRILLING MILLING MACHINE

2
Table of conTenTs
1. General safety rules for all machines 3
2. Additional safety rules 4
3. Safety rules for all tools 4
3.1 User 4
3.2 Use of machine 4
3.3 Adjustment 4
3.4 D. Working environment 4
3.5 Maintenance 5
4. Specifications 5
4.1 Tools selection & proper material range 5
5. Features 5
6. Delivery & installation 6
6.1 Unpacking 6
6.2 Installation 6
6.3 Minimum room space for machine operation 6
7. Use of machine 7
7.1 Control panel 7
7.2 Main machine parts 7
8. Precaution for operation 8
8.1 Before operation 8
8.2 After operation 8
9. Adjusting table slack and compensate for wear (fig 6) 8
10. Clamping, table base, and machine base 8
11. Speed changing and adjust belt 8
12. To change tools 9
13. Extra tooling and accessories 9
14. Tapping equipment 9
15. Specification of t-solt 9
16. Maintaining 10
17. Cleaning & lubricating 10
17.1 Cleaning 10
17.2 Lubrication 10
17.3 Changing the gear box oil 10
18. Troubleshooting 11
19. Circuit diagram 13
20. Exploded drawing A 14
21. Exploded trawing B 15
22. Exploded Drawing C 16
23. Parts List 17

3
HU 50 GC-4 Topline
1. General safeTy rules for all machines
N.B.: Read the instructions carefully in order to avoid any problems.
As with all machinery there are certain hazards involved with operation and use of this machine. Using the
machine with respect and caution will considerably lessen the possibility op personal injury. However, if normal
safety precautions are overlooked or ignored, personal injury to the operator may occur. Observe these rules
insofar as they are applicable to this particular machine.
This machine was designed for certain applications only. We strongly recommend that this machine NOT be
modified in any way and/or used for any application other than for which it was designed.
If you have any questions relative to its application DO NOT use the machine until you have contacted your
dealer.
1. For your own safety read the instruction manual before operating the tool.
2. Keep all guards in place and in working order.
3. Ground all tools.
4. Remove adjusting keys and wrenches. Make a habit of checking the machine before turning it on.
5. Keep the work area clean. Cluttered areas and benches invite accidents.
6. Do not use in a dangerous environment, such as damp or wet locations or expose to rain. Always keep the
work area well-lit.
7. Keep children and visitors away. They must be kept at a safe distance from the machine at all times.
8. Make sure that the work area is not accessible to unauthorised persons. Use padlocks, master switches,
remove starter keys etc.
9. Never overload the machine. The capacity of the machine is at its largest when properly loaded.
10. Do not force the machine or attachment to do a job for which it was not designed.
11. Wear proper apparel. No loose clothing, gloves, neckties, rings, necklaces, bracelets or jewellery: they may
get caught in moving parts. No slip footwear is recommended. Wear a hairnet to contain long hair.
12. Always wear safety glasses and work according to safety regulations. Use a face or dust mask if operation is
dusty.
13. Always secure workpiece tightly using a vise or clamping device. This will keep both hands free to operate
the machine.
14. Do not overreach. Keep your proper footing and balance at all times.
15. Maintain tools in top condition. Keep them sharp and clean. Read the instructions carefully and follow the
instructions for cleaning, lubrication and tool replacement.
16. Lubricate the machine and fill all oil reservoirs before operation.
17. Disconnect tools before servicing and when changing accessories such as blades, bits, cutters etc.
18. Use only recommended accessories. Consult the owner’s manual for recommended accessories. The use of
improper accessories may cause hazards.
19. Avoid accidental starting. Make sure the on/off switch is in the “OFF”position before plugging in the power
cord.
20. Never stand on the machine or tools. Serious injury could occur if the machine is tipped or if the cutting tool
is accidentally touched.
21. Check damaged parts. Replace or repair damaged parts immediately. Check machine for alignment of
moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may
affect its operation.
22. Direction of feed. Feed work into a blade or cutter against the direction of rotation of the blade or cutter
only.
23. Never leave tool running unattended. Do not turn power off until it has come to a complete stop.
24. Alcohol, medication, drugs. Never us the machine while under the influence of alcohol, medication or drugs.
25. Make sure the tool is disconnected from the power supply, before servicing, repairing etc.
26. Keep the original packing for future transport or relocation of the machine.

4
2. addiTional safeTy rules
Always keep in mind that:
• the machine must be switched off and disconnected from the power supply during maintenance and repairs,
• clamped workpieces may only be measured when the machine is switched off.
Never lean over the machine, mind loose clothing, ties, jewellery etc. and wear a cap.
Do not remove safety devices or guards. Never use the machine while a guard is open.
Always use safety glasses for machining rough materials.
Burrs and chips should only be removed using a sweeper or other aid, never with your bare hands!
Never leave the machine running unattended.
Always wear safety glasses!
Warning: failure to follow these rules may result in serious personal injury
Thank you for purchasing the heavy duty drilling machine. If properly cared for and operated, this machine
can provide you with years of accurate service. Please read this manual carefully before using your machine
As with all machinery there are certain hazards involved with operation and use of the machine. Using the
machine with respect and caution will considerably lessen the possibility of personal injury. However, if normal
safety precautions are overlooked or ignored, personal injury to the operator may result. This machine was
designed for certain applications only. We strongly recommends that this machine NOT be modified and/or used
for any application other than for which it was designed. If you have any questions relative to its application DO
NOT use the machine until you contact with us and we have advised you. Your machine might not come with a
power socket or plug. Before using this machine, please Do ask your local dealer to install the socket or plug on
the power cable end.
3. safeTy rules for all Tools
3.1 user
1. Wear proper apparel. No loose clothing, gloves, rings, bracelets, or other jewelry to get caught in moving
parts. Non-slip foot wear is recommended. Wear protective hair covering to contain long hair.
2. Always wear eye protection. Refer to anslz87.1 Standard for appropriate recommendations. Also use face or
dust mask if cutting operation is dusty.
3. Don’t overreach. Keep proper footing and balance at all times.
4. Never stand on tool. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally
contacted.
5. Never leave tool running unattended. Turn power off. Don’t leave tool until it comes to a complete stop.
6. Drugs, alcohol, medication. Do not operate tool while under the influence of drug, alcohol or any
medication.
3.2 use of machine
1. Don’t force tool. It will do the job better and be safer at the rate for which it was designed.
2. Use right tool. Don’t force tool or attachment to do a job for which it was not designed.
3. Secure work. Use clamps or a vise to hold work when practical. It’s safer than using your hand frees both
4. Hands to operate tool.
5. Use recommended accessories. Consult the owner’s manual for recommended accessories. The use of
6. Improper accessories may cause hazards.
7. Avoid accidental starting. Make sure switch is in “OFF”position before plugging in power cord.
3.3 adjusTmenT
Make all adjustments with the power off. In order to obtain the machine. Precision and correct ways of
adjustment
while assembling, the user should read the detailed instruction in this manual.
3.4 d. WorkinG environmenT
1. Keep work area clean. Cluttered areas and benches invite accidents.
2. Don’t use in dangerous environment. Don’t use power tools in damp or wet locations, or expose

5
3. Them to rain. Keep work area well-lighted.
4. Keep chileren and visitiors away. All children and visitors should be kept a safe distance from work area.
5. Don’t install & use this machine in explosive, dangerous environment.
3.5 mainTenance
1. Disconnect machine from power source when making repairs.
2. Check damaged parts. To read every details of trouble shooting, repair it very carefully and make sure The
operator won’t get injure and damage the machine.
4. specificaTions
Drilling capacity 50 mm
Drilling depth 200 mm
Tapping capacity 33 mm
Spindle taper MT4
Spindle speed range 50-1510 omw/min (6)
Feed range 0.1-0.2-0.3-0.4 mm/omw
Number of feeds 4
Column diameter 180 mm
Distance spindle column 340 mm
T-slots 4
Table dimensions l x w 820x240 mm
Base dimensions l x w 550x1000 mm
Motorvermogen 3 kW
Packaging dimensions l x w x h 1130x740x2210 mm
Weight 750 kg
Voltage 400 V
4.1 Tools selecTion & proper maTerial ranGe
Tool type Tool material Work piece material
End mill HSS Non-iron material steel iron
TUNGSTEN CARBIDE Cast iron non-iron material
Face mill TUNGSTEN CARBIDE Non-iron material steel iron
Light material
Drilling HSS Non-iron material steel iron
Tapping HSS Non-iron material steel iron
Light material
5. feaTures
1. This machine has, several uses, such as drilling and also can be equipped with an electric switch for tapping.
2. This machine is of fine quality, can be operated easily, and it is not limited to skilled operators.
3. The drilling operation can be performed by two methods:
4. Hand operation, which makes quick drilling.
5. Worm gear feed operation, which makes slow milling.
6. Bronze adjustable nuts, which adjust the thread clearance and reduce the wear. They also make screws rotated
smoothlyand increase the thread accuracy.
7. Whole column which makes this machine strong, stable, and also keep the high accuracy.
8. Head of tough cast ensures its accuracy lasting and enduring through the treatment of precise boring cylinder,
grinding,and internal stress relief

6
6. delivery & insTallaTion
6.1 unpackinG
1. Transportation to desired location before unpacking, please use lifting jack.(Fig. 2)
1.2. Transportation after unpacking, please use heavy duty fiber belt to lift up the machine.
Always keep proper footing & balance while moving this machine.
Fig.2
Installation:
(1) ALWAYS Keep proper footing & balance while moving this 750kgs machine.
And only use heavy duty fiber belt to lift the machine.
Fig. 3
(2) KEEP machine always out from sun, dust, wet, raining area.
(3) POSITION & tighten 4 bolts into base holes properly after machine in balance.
(4) TURN OFF the power before wiring & be sure machine in proper grounding.
Overload & circuit breaker is recommended for safety wiring.
(5) CHECK carefully if main shaft in clockwise direction while running test. If not,
reverse the wiring then, repeat the test till spindle direction is correct.
(6) Finish removing this wooden case/crate from the machine. Unbolt the machine
from the crate bottom.
(7) Bolt the stand legs to the floor, while using a sturdy stand.
7
Fig.2
Installation:
(1) ALWAYS Keep proper footing & balance while moving this 750kgs machine.
And only use heavy duty fiber belt to lift the machine.
Fig. 3
(2) KEEP machine always out from sun, dust, wet, raining area.
(3) POSITION & tighten 4 bolts into base holes properly after machine in balance.
(4) TURN OFF the power before wiring & be sure machine in proper grounding.
Overload & circuit breaker is recommended for safety wiring.
(5) CHECK carefully if main shaft in clockwise direction while running test. If not,
reverse the wiring then, repeat the test till spindle direction is correct.
(6) Finish removing this wooden case/crate from the machine. Unbolt the machine
from the crate bottom.
(7) Bolt the stand legs to the floor, while using a sturdy stand.
7
6.2 insTallaTion
1. Always keep proper footing & balance while moving this 750kgs machine. And only use heavy duty fiber belt
to lift the machine. (Fig. 3)
2. Keep machine always out from sun, dust, wet, raining area.
3. Position & tighten 4 bolts into base holes properly after machine in balance.
4. Turn off the power before wiring & be sure machine in proper grounding.
5. Overload & circuit breaker is recommended for safety wiring.
6. Check carefully if main shaft in clockwise direction while running test. If not,
7. Reverse the wiring then, repeat the test till spindle direction is correct.
8. Finish removing this wooden case/crate from the machine. Unbolt the machine from the crate bottom.
9. Bolt the stand legs to the floor, while using a sturdy stand.
6.3 minimum room space for machine operaTion
4. MINIMUM ROOM SPACE FOR MACHINE OPERATION
Fig 4
8
4. MINIMUM ROOM SPACE FOR MACHINE OPERATION
Fig 4
8

7
7. use of machine
7.1 conTrol panel
A Start D Tensionindicator
B Stop E Coolant pump switch
C Emergency stop F Manual spindle reverse button
• Press A to turn ON the spindle
• Press B to turn OFF the spindle
• In case of emergency, press the button C.
• D will lighten, when the machine is ON.
• Turn E to the right to turn on the coolant pump, and turn to the left to turn off the coolant pump.
• Turn F to the right to turn the spindle to the left; Turn F to the left to turn the spindle to the right.
7.2 main machine parTs

8
8. precauTion for operaTion
Check all parts for proper condition before operation; if normal safety precautions are notice carefully, this
machine. Can provide you withstanding of accurate service.
8.1 before operaTion
1. Fill the lubricant.
2. In order to keep the accurate precision, the table must be free from dust and oil deposits.
3. Check to see that the tools are correctly set and the work-piece is set firmly.
4. Be sure the speed is not set too fast.
5. Be sure everything is ready before use.
8.2 afTer operaTion
1. Turn off the electric switch.
2. Turn down the tools.
3. Clean the machine and coat it with lubricant.
4. Cover the machine with cloth to keep out the dust.
9. adjusTinG Table slack and compensaTe for Wear (fiG 6)
1. Your machine is equipped with jib strip adjustment to compensate for wear and excess slack on cross and
Llongitudinal travel.
2. Clockwise rotation the job strip bolt with a big screw for excess slack otherwise a little counter clockwise if too
tight.
3. Adjust the jib strip bolt until feel a slight drag when shifting the table.
6
7. ADJUSTING TABLE SLACK AND COMPENSATE FOR WEAR (see Fig. 6)
(1) Your machine is equipped with Jib strip adjustment to compensate for wear and excess slack on cross and
longitudinal travel.
(2) Clockwise rotation the job strip bolt with a big screw for excess slack otherwise a little counter clockwise if too
tight.
(3) Adjust the jib strip bolt until feel a slight drag when shifting the table.
8. CLAMPING, TABLE BASE, AND MACHINE BASE (see Fig 6)
(1) When milling longitudinal feed, it is advisable to lock the cross feed table travel to insure the accuracy of your
work. To do this, tighten the small leaf screw located on the right side of the table base.
(2) To tighten the longitudinal feed travel of the table for cross feed milling, tighten the two small leaf screw on the
front of the table base
(3) Adjustable travel stops are provided on the front of the table for control of cross travel and the desired milling
length.
9. SPEED CHANGING AND ADJUST BELT (Step See Fig 7)
A
B
(1) Turn power off.
(2) Select the suitable R.P.M. from speed charts of table 1.
Fig 7
Fig 6
(3) Turn the speed lever A and B to correct position.
(4) Turn on the power.
11
Fig 6
10. clampinG, Table base, and machine base
1. When milling longitudinal feed, it is advisable to lock the cross feed table travel to insure the accuracy of your
work. To do this, tighten the small leaf screw located on the right side of the table base.
2. To tighten the longitudinal feed travel of the table for cross feed milling, tighten the two small leaf screw on the
front of the table base
3. Adjustable travel stops are provided on the front of the table for control of cross travel and the desired milling
length.
11. speed chanGinG and adjusT belT
1. Turn power off.
2. Select the suitable R.P.M. from speed charts of table 1.
3. Turn the speed lever A and B to correct position. (fig. 7)
4. Turn on the power
Warning: change speed only whenmachine is stopped
Fig 7

9
RPM 500C/500S 550C/550S
Levers 50HZ 60HZ 50/HZ/60HZ
L1 50 60 100
L2 105 125 205
L3 205 250 410
H1 375 450 740
H2 760 915 1500
H3 1510 1810 3000
12. TochanGe Tools
1. Removing Face Mill or Drill Chuck Arbor
Loosen the arbor bolt (see fig 7) at the top of the spindle shaft approximately 2 turns with a wrench. Rap the
top of the arbor bolt with a mallet. After taper has been broken loose, holding chuck arbor on hand and turn
detach the arbor bolt with the other hand.
2. To Install Face Mill or Cutter Arbor
Insert cutter and cutter arbor into the taper of spindle. Tighten arbor bolt detach securely, but do not over-
tighten.
3. Removing Taper Drills
- Turn down the arbor bolt and insert the taper drill into the spindle shaft.
- Turn the rapid down handle rod down until the oblong hole in the rack sleeve appears.
Line up this hole with the hole in the spindle. Insert key punch key through holes and strike lightly with a
mallet. This will force the taper drill out.
13. exTra ToolinG and accessories
Each of machines is equipped with a MT4 spindle taper Contact your local distributor or a major cutting tool
distributor to obtain any of these accessories.
1. Taper Drills
2. Reamers
3. End Mills
4. Cutter Arbor
5. Taps
6. Collets
7. Adapters and Sleeves
14. TappinG equipmenT
This machine can be equipped with an electric switch for tapping operation clockwise or counter-clockwise, and
the working depth also can be adjusted by the limit switch. (Electric switch will be installed according to your
requirement, and you must pay the cost only.)
15. specificaTion of T-solT
The size of T-Solt on table as Fig 8:
Fig 8
14. SPECIFICATION OF T-SOLT
The size of T-Solt on table as Fig 8:
Fig 8
15. MAINTAINING
That's easier to keep machine in good condition or best performance by means of maintaining it at any time than
remedy it after it is out of order.
(1) Daily Maintenance (by operator)
(a) Fill the lubricant before starting machine everyday.
(b) If the temperature of spindle caused over-heating or strange noise, stop machine immediately to cheek it for
keeping accurate performance.
(c) Keep work area clean; release vise, cutter, work-piece from table; switch off power source; take chip or dust
away from machine and follow instructions lubrication or coating rust proof oil before leaving.
(2) Weekly Maintenance
(a) Clean and coat the cross leading screw with oil.
(b) Check to see if sliding surface and turning parts lack of lubricant. If the lubricant is insufficant, fill it.
(3) Monthly Maintenance
(a) Adjust the accurate gap of slide both on cross and longitudinal feed.
(b) Lubricate bearing, worm, and worm shaft to avoid wear.
(4) Yearly Maintenance
(a) Adjust table to horizontal position for maintenance of accuracy.
(b) Check electric cord, plugs, switches at least once a year to avoid loosening or wearing.
16. CLEANING & LUBRICATING
CLEANING
(1) Your machine has been coated with a heavy grease to protect it in shipping. This coating should be completely
removed before operating the machine. Commercial degreaser, kerosene or similar
14

10
16. mainTaininG
That’s easier to keep machine in good condition or best performance by means of maintaining it at any time than
remedy it after it is out of order.
1. Daily Maintenance (by operator)
- Fill the lubricant before starting machine everyday.
- If the temperature of spindle caused over-heating or strange noise, stop machine immediately to cheek it
for keeping accurate performance.
- Keep work area clean; release vise, cutter, work-piece from table; switch off power source; take chip or dust
away from machine and follow instructions lubrication or coating rust proof oil before leaving.
2. Weekly Maintenance
- Clean and coat the cross leading screw with oil.
- Check to see if sliding surface and turning parts lack of lubricant. If the lubricant is insufficant, fill it.
3. Monthly Maintenance
- Adjust the accurate gap of slide both on cross and longitudinal feed.
- Lubricate bearing, worm, and worm shaft to avoid wear.
4. Yearly Maintenance
- Adjust table to horizontal position for maintenance of accuracy.
- Check electric cord, plugs, switches at least once a year to avoid loosening or wearing.
17. cleaninG & lubricaTinG
17.1 cleaninG
1. Your machine has been coated with a heavy grease to protect it in shipping. This coating should be
completelyremoved before operating the machine. Commercial degreaser, kerosene or similar solvent may
be used to remove the grease from the machine, but avoid getting solvent on belts or other rubber parts.
2. After cleaning, coat all possible rusted surface with a light lubricant. Lubricate all points with a medium
consistency machine oil.
17.2 lubricaTion
All ball bearings in your mill/drill are sealed for life, requiring no lubrication. Points requiring
lubrication are:
1. Internal spline drive assembly. Keep this area well lubricated with a good grade non-hardeninggrease, such as
Fiske Company “Lubriplate”. Insert grease in the hole at the top of spindle pulley spline driver. Lube twice
yearly.
2. A light film of oil applied to the quill and column will reduce wear. prevent rust, and assure ease of operation.
3. ) Quill return spring should receive oil (SAE 20) once yearly. Remove cover plate and apply oil withsquirt can or
small brush.
4. IMPORTANT: The gear box should be oiled with a lubricant such as SAE 68 oil in level. Change oil every one
year.
5. Apply Lubriplate to quill pinion every 90 days.
Note. Use extreme care when performing this operation and keep hands clear of pinch points. When using
parafin bar, do this only by turning the sheaves by hand. Do not apply with motor running.
17.3 chanGinG The Gear box oil
Tilt the hard stock over as shown in Fig.1. Open the oil drain plug to allow the oil to drain from the opening
completely. Then lock the oil drain plug and turn the head to be upright position. Remove the oil filler plug fill the
oil to the gear box until the oil lever reach the middle of oil fluid lever indicator. Then lock the plug.

11
18. TroubleshooTinG
Trouble Possible cause Solution
No running after
switch on
Main switch interruption while volts
irregula
Adjust input voltage and draw back the main
switch
Break down of fuse in switch box Replace with new one
In case of too much current,
the overload relay jumps away
automatically
Press the overload relay, and it will
return to the correct position
Motor Overheat
and no power
Overload Decrease the load of feed
Lower voltage Adjust to accurate voltage
Spoiled contact point of magnetic
switch
Replace with new one
Breakdown of overload relay Connect it or replace with new one
Motor is poor Replace with new one
Break down of fuse or poor contact
with wire (it is easily, to spoil motor
while short circuit)
Switch off power
source at once and replace fuse with new one
The temperature of
spindle bearing is
too hot
Grease is insufficient Fill the grease
The spindle beating is fixed too tight turning with no speed and feel the tightness
with hand.
Turning with high speed for a long time Turn it to lightly cutting
Lack of power
with main spindle
revolving
Motor has burned out Change a new motor
Fuse has burned out Replace with new one
Table travel has not
balanced
The gap of spindle taper too wide Adjust bolt in proper
Loosening of leaf bolt Turn and fasten in place
Feed too deep Decrease depth of feed
Shake of spindle
and roughness of
working surface has
taken place during
performance
The gap of spindle bearing too wide Adjust the gap in proper or replace bearing
with new one
Spindle loosening up and down Make two of inner bearing covers on the top
tight each other. Do not over-tighten two inner
bearing covers with the taper bearing; it is ok as
long as no gap between them
The gap of taper sliding locate too wide Adjust the tension of bolt in proper
Loosening of chuck Fasten chuck
Cutter is dull Re-sharpen it
Work-piece has not hold firmly Be sure to tighten work-piece
Micro feed does not
work smoothly
Loosening of clutch Be sure to tighten it
Worm and worm shaft has worried out Replace with new one
Loosening of hand-wheel fixed screw Be sure to tighten it.
Without accuracy in
performance
The balance of the work piece must be considerated as the principle balance
while holdingwork-piece
Often use of hammer to strike work
piece
Forbidden to use hammer to strike work-piece
Unaccurate horizontal table Cheek and maintain table for keeping accurate
horizontal after a period of use
Excessive vibration Motor out-of-balance Balance or replace problem motor
Bad motor Replace motor

12
Motor stalls
Over feeding Reduce feed rate
Dull drill Sharpen drill and keep sharp
Motor not building up to running
speed.
Replace or repair motor. Check fuses in all three
legs on three
phase motors and replace if necessary.
Noisy operation:
Excessive vibration Check remedy under excessive vibration
Improper quill adjustment Adjust quill
Noisy spindle Lubricate spindle
Noisy motor Check motor bearings or for loose motor fan.
Drill or tool heats
up or burns work
Excessive speed Reduce speed
Chips not clearing Use pecking operation to clear chips
Dull tool Sharpen tool or replace
Feed rate too slow. Increase feed enough to clear chips
Rotation of frill incorrect. Reverse motor rotation.
Failure to use cutting oil or coolant (on
steel).
Use cutting oil or coolant on steel.
Drill leads off
No drill spot Center punch or center drill work-piece.
Cutting lips on drill off center. Regrind drill.
Quill loose in head Tighten quill.
Bearing play Check bearings and reseat or replace if
necessary.
Excessive drill
run-out or wobble
Bent drill Replace drill. Do not attempt to straighten
Bearing play Replace or reseat bearings.
Drill not seated properly in chucks. Loosen, reseat and tighten chuck.
Work or fixture
comes loose or
spins
Failure to clamp work-piece or work
holding device to table
Clamp work-piece or work holding device to
table surface

13
19. circuiT diaGram

14
20. exploded draWinG a
33

15
34
21. exploded TraWinG b

16
35
22. exploded draWinG c

17
1 250001A Head Body 1
2 250002A Head Body Cover 1
3 HP304 Miter Pin 2L05x7#
4H S261 Hex. Socket Head Screw M10x35L 6
5 HK094 Key 1L86x7x8
7 250007 Gear 1T42
9 250009 Gear 1T24
11 HCR20 C-Retaniner Ring 174R
12 CA6005-2RS Bearing 6005-2RS1
13 HCS13 C-Retaniner Ring 752S
14 250014AS 3 Speed Change Spindle Asbly 1
15 290089 Spring 2
16 HB001 Steel Ball
17 257334 Chuck Arbor MT4 - JT6 1
17 257334A Chuck Arbor MT4 - B16 1
17 257334B Chuck Arbor MT4 - JT41
18 HP218 Spring Pin 2L51x5
24 250024 Speed Change Bracket 1
25 250025 3 Speed Handle 1
26 HP221 Spring Pin 1L03x5
27 250027 Long Speed Change Handle 1
28 HCS04 C-Retaniner Ring 451S
29 HG010 Oil Seal 2t7x52x51
30 CA6004ZZ Bearing 8ZZ4006
31 CA6004 Bearing 14006
32 HS281 Hex. Socket Head Screw M12x35L4
33 Motor 1
34 250034 Locknut 2
35 HS422 Hex. Socker Headless Screw 01L8x6M
36 HP214 L02x4niPgnirpS 1
37 S629 Hex. Socker Headless Screw PT1/4"X11L1
38 2401001-2 Main Shaft Cover 1
39 HB202 Fluid Lever Indicator 203M
40 HCR05 C-Retaniner Ring 424R
41 250041 Driven Spindle 1
42 250151B Name Plate 1S005
43 250043 Gear 1T83
44 HK037 Key 1L08x6x6
45 250045 Gear 1T62
46 250046 Gear 1T05
49 250049 Handle Support 1
50 HS230 Hex. Socket Head Screw 8L02x6M
51 250051 Cover 2
52 250052AS High - Low Speed Spindle 1
54 HO030 O-Retainer Ring 2
56 250056 Speed Change Bracket 1
57 250057 High - Low Speed Handle 1
58 250058 Short Speed Change Handle 1
59 250059 Outer Bearing Plate 1
60 HT003 Hex. Socket Head Screw 41L01x6M
61 HCR16 C-Retaniner Ring 2001R
62 250062 Oil Seal Ring 2
63 HG016 Oil Seal
55x75x10 2
CCOODDEE NNOO PPAARRTT NNOO DDEESSCCRRIIPPTTIIOONN SSPPEECCIIFFIICCAATTIIOONN QQTTYY
~
~
~
~
23. parTs lisT
1
1
4
1
2
H

18
CCOODDEE NNOO PPAARRTT NNOO DDEESSCCRRIIPPTTIIOONN SSPPEECCIIFFIICCAATTIIOONN QQTTYY
64 CA6211-2RS Bearing 6211-2RS2
65 250065 Spindle Taper Sleeve 1
66 HCS29 C-Retaniner Ring 256S
67 HK056 Key 1L54x8x8
68 250068 Gear 1T87
69 250069 Gear 1T84
70 250070 Chuck Arbor Bolt MT4 M16x560L1
71 250071 Spindle Shaft 14TM
72 HCS23 C-Retaniner Ring 104S
73 CA6008ZZ Bearing 2ZZ8006
74 HW209 Washer 101WA
75 HN102 Nut 201NA
77 250077 Bushing 1
78 250078 Rack Sleeve 14TM
79 6127 Screw Key 1"8/3
80 N005 Hex. Nut 1"8/3
81 250081 Bearing Cap 1
82 250082 Rubber Flange
83 250083 Head Lock (Front) 1
84 250084 Head Lock (Back) 1
85 6124 Handle Rod 1
86 HW006 Washer 121M
87 250087 Speed Change Handle 2
88 250088 Speed Lever 2
89 HS413 Hex. Socker Headless Screw 1L5x5M
90 HS430H ex. Socker Headless Screw 6L01x8M
91 250091 PF Driven Spindle 1
93 250093 Gear 1T43
94 250094 Gear 1T81
95 HK014 Key 1L05x5x5
96 250096 Bushing 3
97 GHCS09 C-Retaniner Ring 402S
98 250098 PF Transmission Spindle 1
99 HK007 Key 1L51x5x5
100 250100 Gear 1T24
101 HG011 Oil Seal 1t8x24x52
102H K006 Key 1L01x5x5
103 291050 Clutch Block 1
104 250104S Gear Set 1T03
105 250105 Bushing 1
107 2450057 Bushing 1
108 250108 Spring
112 250127S Oil Feeding Tube Asbly 1
115 250128 Oil Returning Tube 1
116 CA7010AW Bearing 2WA0107
117 250124 Motor Plate 1
118 250125 Gear Box Gasket 1
120 250231S Spring&Spring Cover Set 1
121 250232S Spring Base Set 1
123H S519 Cross Round Head Screw 2L01x5M
124 HW005 Washer 18M
~
~
~
~
2
1
H

19
CCOODDEE NNOO PPAARRTT NNOO DDEESSCCRRIIPPTTIIOONN SSPPEECCIIFFIICCAATTIIOONN QQTTYY
126H B603 Oil Hole Plug M16xP1.5x8L1
127H B702 Vent Plug 1"8/1TP
128 250123 Bottom Plate 1
129 HS241 Hex. Socket Head Screw 1L51x8M
130 62276 Nozzle Cock Support 1
131 250250 Valve 1'4/1
132 250251 Nozzle 1"4/1
133H S422 Hex. Socker Headless Screw 1L8x6M
134H S241 Hex. Socket Head Screw 1L61x8M
136H I403 Flying Rings 221M
137H I404 Flying Rings 161M
138 257327AS Switch Set(For CE Only) 1
139 257328S Limit Switch Support Set 1
143 257345S Chuck Guard Asbly(For CE Only) 1
401 250401 Gear Box 1
402 2450020 Release Block 1
403 2450051 Pin 3L31x4
404 CA6004ZZ Bearing 4ZZ4006
405 250402 Transmission Worm Shaft 1
406H K013 Key 1L54x5x5
407 250403 Gear 1T02
408 250404 Gear 1T42
409 250405 Gear 1T03
410 250406 Gear 1T04
411H CS09 C-Retaniner Ring 102S
412 250407S Change Gear Lever Set 1
416 250408 Shaft 1
417H K009 Key 1L52x5x5
418 250409 Worm Shaft 1
419 HS422 Hex. Socker Headless Screw 6L8x6M
420 2450074A Bushing 5
421 250410 Gear 1T02
422 250411 Gear 1T03
423 250412 Gear 1T63
424 250413 Gear 1T04
425 2450089A Bushing Bracket 1
426H CR05 C-Retaniner Ring 324R
427 250414 Cover 1
428 250415 Gear Shaft 1
429 HB001 Steel Ball
4302 90089 Spring 2
431 2450079 Speed Lever 2
432 250416 Clutch Spindle 1
433 250417 Clutch Worm Shaft Spindle 1
434 250205 Gear 1T53
435H S220 Hex. Socket Head Screw 2L02x5M
436H K010 Key 1L03x5x5
1hctulCesreveR814052734
1tfahSmroW914052834
1gnirpS4500542934
~
~
1
H
H
H
H
H
H
H
H
H
H
H
H

20
1gnihsuB7500542044
4
51SgniRreninateR-C40SCH14
4
2
ZZ2026gniraeBZZ2026AC24
4
1
53RgniRreninateR-C40RCH34
4
1
ydoBeldnaH02405244
4
1
teSesaBelacSSA12405254
4
1
wercSteSesaBelacS330054284
4
1
teSgnihsuBhctulCS22405294
4
2
doReldnaH32405225
4
2
niPdoReldnaH42405235
4
1
pirGdexiFesaBdetaudarG360054245
4
1
"61/5tuN.xeH700N55
4
1
wercST890054265
4
1
teSesaByeKhctulCS420054275
4
1
tfahSnoiniP52405206
4
1
raeGmroW320054216
4
2
yeK220054226
4
2
52SgniRreninateR-C31SCH36
4
2
yeKhctulC620054246
4
2
gnirpS820054256
4
1
teSwercShtulCS690054276
4
2
5EgniRgniniateRE800EH86
4
2
bonK01007617
4
1
L01x6MwercSdaeHssorCtalF416SH27
4
480
HS320Hexagon scre M8x100
4
1
revoCmroW72405218
4
2
L52x5MwercSdaeHdnuoRssorC225SH28
4
1
cirteMrotacidnIgnitsujdAorciMB82405238
4
1
lairepmIrotacidnIgnitsujdAorciMA82405238
4
1
L21x"4/1wercSkniL3-206658
4
1
leehWSB241668
4
1
L01x8MwercSsseldaeHrekcoS.xeH034SH78
4
1
8MrehsaW500WH88
4
1
L51x8MwercsnogaxeH142SH98
4
3
elacS060054209
4
6
L4x2teviR100HH19
4
1
cirteM)cirteM(lebaLdeepSgnideeFB03405229
4
1
lairepmI)lairepmI(lebaLdeepSgnideeFA03405229
4
1
lebaLhctulC23405249
4
1
"8/1TPelppiNesaerG105BH59
4
1
t5.1rehsaWB001054269
4
1revoCA334052794
CCOODDEE NNOO PPAARRTT NNOO DDEESSCCRRIIPPTTIIOONN SSPPEECCIIFFIICCAATTIIOONN QQTTYY
1L13elbaT1-8266106
2kcolBdexiF9226206
2gniRdexiFelbavoM0326306
604 S402H ex. Socket Head Screw1 /4"x1/2"L2
5"61/3llaBliO011BH506
3teSleehWeldnaHelbaTSB6066606
3bonK533752706
3L01x6MwercSdaeHtekcoS.xeH712SH806
171
hctulCelbaT0266906
21
~
~