SPECIFICATON
Model No.
Image Sensor
Effective Pixel
Cell Size
Resolution
TV Type
Sync. Type
Scanning System
Video Output
Min. Illumination
S/N Ratio
LENS
Operation Temp.
Dimension
Weight
Day & Night
Shutter
Power Supply
G1
60 6
NTSC / PAL
Internal
2 : 1 Interlace
1.0Vp-p(Sync, Negative) Termination 75Ω
γ= 0.45 Typ.(Adjustable)
Electronic D&N
48dB over(AGC OFF)
Average test illuminance by front view
1/50(1/60) ~ 1/100,000 sec
Regulated 12V DC
Max. 105mA(at 12V DC)
Non-polarity
CS Mount
-10℃ ~ 50℃
-20℃ ~ 60℃
x x 51
Approx. 100g
SK-B260/
Color : 0 TV-Line, B/W : 80 TV-Line
0.1 Lux(at F/1.2)
36.5mm(W) 36.5mm(H) mm(L)
Gamma
Characteristic
Test Illuminance
Area
Current
Consumption
Reverse Polarity
Protection
1/3" COLOR SONY SUPER HAD CCDⅡ
768(H) 494(V)Pixel(NTSC)
752(H) 582(V)Pixel(PAL)
x
x
6.35㎛(H) 7.4㎛(V)(NTSC)
6.5㎛(H) 6.25㎛(V)(PAL)
x
x
Preservation Temp.
Fixed focal lens or Vari-focal auto iris lens
In case of manual lens selection, adjust the
brightness
Shutter speed auto adjustable
Select shutter speed manually
Determines that use the AGC function or not
and AGC level selectable(You can not use the
Auto D&N change mode when AGC is off)
Digital Wide Dynamic Range
BLC function
High Light Mask function
In case of AUTO mode, the function will off in
daytime and on at night
According to the threshold value, the camera
will recognize as High light or not.
Color temperature 2500 ~ 9500°K
Adjust the Red or Blue values to shift the color
of the object
Move the camera lens toward to white paper
then press the enter button to find the optimal
white balance for current environment
Auto day&night switching mode
Fixed at color
Fixed at B/W
Determines whether to transmit the burst signal
or not in B/W mode
You can select brightness of illumination about
changing the day ↔ night mode
You can select the duration time about chainging
the day ↔ night mode
Set a horizontal image inversion
Sharpness adjustable
Gamma adjustable
Determines whether to use the brightness
compensation of four lens' corners(LSC) or not
The LSC level selectable
Adjust Red tone of the image
Adjust Blue tone of the image
MANUAL, DC
0 ~ 100
AUTO
1/60(1/50) ~
1/100,000
OFF, LOW,
MIDDLE, HIGH
OFF, LOW,
MIDDLE, HIGH
OFF, ON
OFF, ON,
AUTO
0 ~ 100
ATW
MANUAL
AWC↓
AUTO
COLOR
B&W
OFF, ON
75 ~ 170
40 ~ 135
3 ~ 15
OFF, ON
0 ~ 50
0.45, 0.6, 1,
USER
OFF, ON
0 ~ 50
0 ~ 200
0 ~ 200
LENS
E.SHUTTER
AGC
DWDR
BLC
HLC
AWB MODE
D&N MODE
MIRROR
SHARPNESS
GAMMA
LSC
R-Y GAIN
B-Y GAIN
PATTERN
GENERATOR
BRIGHT
HLC THR
BURST
COLOR→BW
BW→COLOR
DELAY TIME
LSC LEVEL
OSD MENU
OFF, ON
NONE
MESSAGE
MASK
0 ~ 255
1 ~ 15
OFF, ON
BLACK,
GRAY …
ENGLISH,
KOREA …
OFF, ON
Determines whether to use the motion detection
function or not
No display on the screen though movement is
detected
The words 'MOTION' appear on the screen
when movement is detected
Motion detection area appear on the screen
when movement is detected
Motion detection sensitivity
Set the duration of outside alarm. If the way of
display is message, it means display time of
message
Display each privacy mask or not. Press the
enter button to move into the privacy mask
setting section, whenever you press the enter
button, the mask color is changed. When the
mask color is red you can adjust the size by
up, down, left and right button. When the mask
color is blue you can set the position of mask
by up, down, left and right button. Press the
enter button for a few second to escape
Select mask color
Select language
Display the camera ID on the screen
MOTION
MASK
1, 2, 3, 4
MASK
COLOR
LANGUAGE
NAME
DISPLAY
DISPLAY
SET
WINDOW
ALL SET↓
ALL
CLEAR↓
SENSITIVITY
HOLD TIME
EDIT
POSITION
Function
setting menu Select menu ContentsSub menu
1. EXPOSURE
3. DAY&NIGHT
2. WHITE
BALANCE
4. IMAGE
ADJUST
6. PRIVACY
MASK
5. MOTION
10. EXIT
8. SPECIAL
9. FACTORY
SET
Test signal. Press the enter button, color bar appeared on the
screen and press any key to return to menu
Press the enter button to move into the motion detection area
section to set the 64 areas.
Press the enter button for a few second to move out.
Press the enter button to select all area
Press the enter button to remove all area
Press the enter button to move into the name setting section.
You can choose the letter by using up and down button and
move next letter by using left and right button. Press the enter
button for a few second to move out.
Press the enter button to move into the position setting section.
You can move the camera ID to your wanted position by using
up, down, left and right button.
To reset your camera to factory default condition.
Notice : Lens and language is not changed.
Save the value and then restart.
3B15808A
※All specification is subject to change without notice to improve the quality.
