HW Group Damocles MINI How to use

Damocles MINI –starting guide
HW group
www.HW-group.com
Starting Guide –Damocles MINI
First steps for I/O control with Damocles
1) Connecting the Damocles MINI
Green POWER LED on the RJ45 socket lights up –power supply is OK
Yellow LED on the RJ45 socket flashes –connection to 10 Mbit network is OK
2) Configuring the IP address –UDP Config
The UDP Config executable is located in the root of the
supplied CD (Windows and Linux version), or it can be
downloaded at www.HW-group.com, Software -> UDP
Config.
Click the icon to run UDP Config. The program
automatically starts searching for connected
devices.
Click the Find Devices button to start searching
for devices.
The program looks for devices on your local network. To
identify a particular Poseidon unit, look at its MAC address (printed on the label
at the bottom of the unit). Double click a MAC address to open a dialog window
with basic device settings.
Click the Apply Changes button to save the settings.
Note: Contact your network administrator if you are unsure about these
settings.
Damocles MINI
1.5) Connect Damocles to the Ethernet (patch cable to switch, or cross-over cable to
PC)
1.2) Output (double-throw relay contact) to turn on/off
external devices (fans, A/C, heating, horn, etc.)
1.1) Check the DIP switches. For installation, set them as shown
in the picture (DIP1=Off, DIP2=Off).
1.3) Connect the power adapter to an outlet (230 /
110V) and to the 12V power supply connector.
1.4) Dry contact inputs to connect sensors with Dry
Contact outputs (buttons, relay contacts, door contacts).

Damocles MINI –starting guide
HW group
www.HW-group.com
3) WWW pages of the device
Enter the IP address of the device to the address field in your web
browser, or run UDP Config and click the IP address in the list of
devices.
Click on the link „Graphic Flash SETUP“ to open graphic Setup interface
(Flash Setup).
Retrieving current readings
XML –/values.xml file, format described using XSD –for download on the main page, detailed
comments on XML structure are available in the manual.
SNMP –the poseidon.mib description file can be downloaded from the main page. The SNMP
ports (defaults are 161 and 162) can be changed in Flash setup.
Modbus/TCP –structure description is available in the manual, or in application examples.
Standard port 502 is open for reading.
•Reset to factory defaults
Toggle DIP1 several times within 5 seconds after powering up. Default settings
contains none passwords.
DIP1
•Disable any configuration changes (online demo mode)
While DIP2=On any configuration change disabled.
Note: Set Dip2=Off to be able change IP address configuration
DIP2
Adjustable link to
service organization
Current state of
inputs
Click to open Flash
SETUP –graphical
interface
Statement of the
setting of ALARM for
each input
Name of the particular
unit of Damocles
Current state of
outputs
IP address of Damocles unit

Damocles MINI –starting guide
HW group
www.HW-group.com
4) Flash SETUP of device
To open the FLASH page, support of FLASH
application has to be installed in your PC. If PC is
connected to Internet, necessary Plug-in is
downloaded automatically, if the computer isn´t
connected, it is necessary to install Plug-in from
supplied CD -
\Damocles\install_flash_player_7.msi.
For detailed description of Flash SETUP, see product
manual.
5) We test the inputs and outputs
To prove state of inputs and control outputs, use WEB >> Flash Setup >> bookmark Status
Outputs
oSet „Reload values every 1 [s]” below on the right and press “Start”
oIn the category Outputs, change the value of one of the outputs and press „Apply
Changes“. You will hear a click of relay in Damocles unit and signal indicator LED of
output will signal the state of output relay.
oThe outputs are labelled NO (Normally Open) and NC (Normally Close), middle pin
is common. Interconnection of inner contact relay corresponds with the states on the
picture.
Inputs
oTo prove the inputs, it´s enough to connect the inputs by wire or clip.
oSwitch the function „Counter“ on, from Flash Setup interface you can find the number
of pulses.
NO NC
Output On
NO NC
Output Off
Input On
Input Off
Output 1

Damocles MINI –starting guide
HW group
www.HW-group.com
6) Alarms and Alarm Alert via Email
Damocles supports warning of state change on one input –„Single Alarm“, and at same time
warning of presence of certain combination of inputs „Group Alarm“.
For each input, you can set Alarm state (at value On or Off) and you´ll be informed about state
change by sending Email or SNMP Trap. >> Bookmark Inputs, green column „Single Alarm“.
You need to activate each Alarm >> Bookmark Alarms, column „Enable“.
For each Alarm, you need to set where it´ll be sent. Four destinations for SNMP Traps (labelled
A,B,C,D) and two destinations for Email (labelled E,F) are available >> Bookmark Alarms,
column „SNMP“ or „E-mail“.
It´s necessary set and permit the destinations A up to D for SNMP and E,F for Email.
Test sending Email
For sending Email directly from device, check the setting of these variables
IP address GateWay >> Bookmarker Setup, group „Network Settings“ item „Gateway“.
DNS server Settings >> Bookmarker Setup, group „Network Settings“ item „DNS“.
SMTP server Settings >> Bookmarker Email & SNM Setup, group „Email Settings“
Use sending test Email for function test
>> Bookmarker Email & SNM Setup, group „Email Settings“
Group Alarm
An adjustable combination of states of some inputs can cause Alarm state which can locally connect
output up. Description of these conditions setting and examples, you can find in detailed manual.
7) Output setting from your SW
Your own SW can use protocols SNMP, XML or Modbus/TCP for outputs setting
For simple output setting from command line, you can use program DamPosIO. This program
records XML file with required outputs state on defined IP address. Program is available for
Windows, for Linux in source codes, included in supplied SDK. >> find on supplied CD.
For outputs control, you can use program PD Hawk, which is able to answer to coming alert
state of Alarm, for example, connect relay up over network. >> find on supplied CD.
You can protect the change of outputs state by password, range of IP addresses or you can completely
prohibit it by setting of DIP 2 to ON position. After put DIP 2 on, it´s impossible change the outputs state.
Others information about setting, you can find in the manual or on the pages: www.HW-group.com.