Press the Menu button.
Scroll to Mirror using or .
Select Mirror by hitting the Enter button.
Toggle using or to highlight F in red.
Select F by hitting the Enter button.
To revert back to the Mirror-i age view, repeat above steps but select M instead of F.
Brightness
The brightness of the unit can easily be decreased or increased.
To Adjust Brightness
Press to decrease brightness.
Press to increase brightness.
To Power Off your Hyndsight Syste
Hold Ca era Power button for 2-3 seconds until i age disappears fro Monitor. Monitor screen will be white and will display Signal Lost
along the top of the screen.
Hold Monitor Power button for 3 seconds until screen goes black.
Note: To place Monitor in power save ode at any ti e, press Monitor Power button for 1 second to display a di i age. Press the Monitor Power
button again for 1 second to restore full color display. Your Monitor is not fully Powered Off until both the Monitor Green Indicator Light is off and the
screen is dark black. Power save ode is ideal for conserving Monitor battery life without having to fully turn off the syste when not in i ediate use.
FLUSH BRACKET MOUNTING
To attach the Ca era or Monitor to the desired s ooth, clean, flat, non-porous surface, follow the instructions below. Note: The ounting surface and
the Suction Cup should be clean and dry. Wipe with a clean, da p cloth and let dry co pletely. The Flush Mount should be installed at roo
te perature (avoid extre e heat or cold). Do not oisten the Suction Cup.
Thoroughly clean the s ooth, flat, non-porous surface, aking sure the surface is dry and free of scratches.
Twist the Ca era or Monitor onto the flush ount's threaded ounting stud. Do not re ove the Rubber Washer.
Hold the Ca era in place and fir ly tighten the Lock Ring.
Position the Suction Cup Lever in the "down" position.
Position the Suction Cup on your ounting area. In order to re ove the Flush ount easily, HVS reco ends that the Suction cup Release
Tab be at the botto of the installation area.
Push the Suction Cup fir ly against the ounting surface (the Suction Cup Lever should be in the "down" position). Press the Suction Cup
Button and pull the Suction Cup Lever up and over the Button. You will feel the Button ove out during this procedure; this action locks the
Suction Cup into place.
Loosen the Flush Mount Adjusting Knob, position the Ca era or Monitor, and then retighten the Adjusting Knob.
Check the Ca era's position as necessary by loosening the Adjusting Knob. Tighten securely when in position.
To release the Suction Cup, ove the Suction Cup Lever back into its "down" position. Lift the Suction Cup Release Tab to help break the
hold.
INTENDED USE
Hyndsight Vision Systems wireless cameras and monitors are to be used as an aid for visualizing blind spot conditions or for monitoring locations not always in clear sight. Use of your own common sense
and judgment is always indicated before and during use of this product. Hyndsight is not responsible for accidents of actions that result under use of this product.
IMPORTANT SAFETY NOTICE
Program you settings before you operate any vehicle.
Do not program product while driving or while in motion. hen adjusting settings, stop in a safe and legal manner before doing such operations.
Hyndsight Vision Systems, Inc. products are designed for use in outdoor activities. hile using your Hyndsight product, safety rules must be followed to prevent accidents that can result in injury or death
to yourself and/or others.
Distractions can be dangerous and result in an accident in which you or others could be injured. Please do not solely rely on screen image alone. No technology is a replacement for your attentiveness.
Do not disassemble the Camera or Monitor.
Do not attempt to remove the internal, non-replaceable battery in the Camera or the Monitor. Do not expose the product to abnormal conditions such as extreme heat or humidity or prolonged sun
exposure.
hen disposing of the unit, have the batteries removed and recycled by a professional waste electronics treatment provider.
Do not use paint thinner or rubbing alcohol to clean unit.
Do not subject unit to strong impact. Do prevent the Camera and Monitor from falling.
Do not submerge the Camera or Monitor in water. Do not subject unit to prolonged exposure to rain, snow, and other outside environments.
Sunglasses with polarized lenses may impair the visibility of the display.
Do charge the units indoors in dry conditions. Do not charge the units around water or during rain when unit is installed outdoors. Doing so may cause electrical shock and/or injury to you or the device.
CAUTION
In order to prevent improper operation of the AC Adaptor, please read the user manual carefully. For your safety, please use only the AC Adaptor provided. The manufacturer will not be responsible for
any losses caused by converters and chargers not provided by the manufacturer. IMPORTANT Please use only the socket match with the AC Adaptor. Use of improper socket may cause electrical and
fire damage. Only charge the Camera and Monitor in dry environments. Charging the Camera and/or Monitor in the rain or in a wet environment may cause electrical shock, fire, personal injury and/or
product destruction. Improper use of the Camera and/or Monitor and accessories will void the warranty.
