Hyundai H-HT5115-N User manual

ДОМАШНИЙ КИНОТЕАТРHOME THEATREРуководство по эксплуатации Instruction manualH-HT5115-N

23Table of contentsBefore you startDear customer!Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.999999910101010121313141414141415151616171717171819Table of contents Before you start Utilization of the product Important safeguardsSupported formatsConnectionVideo/audio system connectionOperationFront panelRear panelRemote controllerChanging the batteryButton functionsStandby Open/CloseUSB/DiscCopy/Title Subtitle Angle Menu/RipPlay/PauseCursor buttonsNumber buttons EnterStopStepFast forwardRewindPrevious/nextProgSelect sourceSetup GotoRepeatV-ModeA-BAudioMute23334556667788888888888888888999999999Volume+/- OSDZoomA-ModeS-Effect ToneKey+/-Ch-LevelSystem setupGeneral setupAudio setupDolby digital setupVideo setupPreference setupOther functionsRadio tuner operationsKaraoke operationUSB operationMP3/Compressed video playbackJpeg playbackRippingCopying dataDeleting data from USBGeneral informationHandling compact discsCleaning discsAccessoriesTroubleshootingSpecification

23Table of contentsBefore you startIf you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.Please contact your local authorities for the correct method of disposal. By doing so, you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.Utilization of the productImportant safeguards Alerts the user to the presence of dangerous voltage within the product’s enclosure. Alerts the user to the presence of important operating instructions. To reduce the risk of electric shock or fire, do not open the cover. Refer servicing to qualified service personnel. This mark indicates this unit belongs to class 1 laser product.• To prevent the risk of fire or electric shock, don’t allow water to come into contact with the device and don’t use the device in high humidity conditions.• The device is equipped with high voltage components and a laser system, hence you shall not open the device and repair it by yourself. The laser beam is dangerous to eyes when the housing is removed. Don’t look at it.• When the device is moved from cold premises to the warm room or vice versa, condensate may form on the laser head and the device may not operate properly. In this case please turn the device on for 1-2 hours without disc before playback to heat it to a proper operation temperature.• Don’t try to manually open or close the disc tray to load discs.• Disconnect the receiver only when there is no disc therein.• If you are not going to use the device for a long time disconnect it from the wall outlet.• Before turning the device on, please make sure that you have connected it properly, adjust the volume of speakers and amplifiers of your radio system to the minimum. Adjust the volume as necessary only after normal playback has started to avoid damage of your audio system.• Use supply sources of rated voltage, otherwise the unit may not function or may be damaged.• Place the unit on a horizontal surface. Keep the unit ventilated. Don’t block the heat hole. Overheat may cause malfunction.• Do not place any objects on the player’s cover, this may make it function improperly (incorrect playback).• Please place the device in a dry and well-aired area. Do not place it near heating units or expose it to direct sunlight, mechanical vibration, humidity or excessive dust.• If using power plug and appliance coupler as a cutting-connecting device, it should be operated easily.• Never use liquid detergents, abrasives or organic compounds (alcohol, gasoline, etc) to clean the unit body.W a rning
RISK OF ELECTRIC SHOCK
DO NOT OPEN

4Before you start• All repairs and technical service should be made by qualified specialist from service centers.All images provided herein are schematic drawings of real objects and may differ from their real images.Supported formatsDisc typesSymbolContentsDVDCompressed digital audio - videoHDCDCompressed digital audioMPEG4 (DivX)Compressed digital audio - videoVideo-CD (VCD)Compressed digital audio - videoCDDADigital audioMP3Compressed digital audioKodak Picture CDCompressed digital static imageJPEGCompressed digital static image

5ConnectionVideo/audio system connection Before you start connection of external devices, ensure that power of the unit is switched off.Following outputs are available in this unit.Composite videoUse the yellow plug of an AV cable to connect the composite video output of this unit to the video input of a TV/monitor.Component videoUse a 3-core AV cable to connect the component outputs of this unit to the corresponding inputs of a TV/monitor.S-videoUse an S-Video cable to connect the S-Video output of this unit to the S-Video input of a TV/monitor.Stereo audioUse a pair of AV cables (red for right/white for left) to connect the stereo audio outputs of this unit to the TV or a stereo input of power amplifier.SCARTUse a 21-pin SCART cable to connect the SCART output of this unit to the TV/monitor SCART input.Coaxial digital audioUse a special coaxial cable to connect the coaxial output of this unit to the coaxial input of an external device.Speaker connectionUse a special cables to connect the speaker output terminals of this unit to the corresponding speakers.Line in connectionThis unit has an extra group of audio input terminals. You can input the analogue stereo audio signals from extra devices such as DVD, VCD, CD, VCR player, etc. Use the audio cable (red for right, white for left) to connect the stereo audio output terminals of an extra device to the stereo input terminals (LINE IN) of this unit. Its corresponding signal source is LINE, which can be available by pressing SOURCE SELECT button. • The connection you should make depends on the TV/monitor input terminals. Don’t make all the connections at the same time; otherwise the produced picture will be affected.• The physical connection should accord to the audio/video output setup of this unit.

6OperationControl elementsFront panel1234568791. STANDBY button2. Disc tray3. OPEN/CLOSE button4. Display5. Microphone socket6. button7. USB port8. button9. VOLUME knobRear panel12345678910 1. Power switch2. Speaker output3. Line input4. Composite video output5. Component video output6. S-Video output7. Stereo audio output8. Coaxial digital audio output9. FM antenna jack10. SCART connector

7OperationRemote controller (RC) 1. STANDBY button2. PROG button3. V-MODE button4. A-MODE button5. GOTO button6. SETUP button7. AUDIO/MEMORY button8. MENU/RIP/MO/ST button9. TITLE/COPY/FM buttons10. ENTER button/Cursor buttons11. SOURCE SELECT button12. button13. //RADIO+/- buttons14. button15. CH-LEVEL button16. USB/DISC button17. KEY+/- buttons18. OSD button19. OPEN/CLOSE button20. Number buttons21. SUBTITLE/AUTO button22. ANGLE button23. button24. VOLUME+/- button25. //SEARCH+/- button26. TONE button27. S.EFFECT button28. REPEAT button 30. ZOOM button29. A-B button 31. STEP buttonChanging the battery1. Remove the battery compartment cover on the back of the RC.2. Insert the batteries into the battery compartment making sure that the correct polarity is observed.3. Install the cover back.• Use two AAA/1.5V batteries for the RC. The RC should be pointed at remote sensor within 8 meters and within 30 degrees at the left or the right side.• Take the battery out of the RC if it is not used for a long time.• Do not mix new and used batteries or different types of batteries. Weak batteries can leak and severely damage the RC.12312345678910192021222324252627282930311112131415161718/RIP
COPY

89OperationOperationButton functionsSTANDBYPress this button to put the unit to standby mode; press the button again, to turn on the unit. To turn off the unit completely, press the Power switch on the rear panel of the unit.OPEN/CLOSEPress this button when power is on, the disc tray is pushed out. Put the disc on the tray with the title faced up. Press OPEN/CLOSE button again to close the disc tray.USB/DISCPress this button to select a signal source (USB/DVD).COPY/TITLE• When playing a DVD disc, press COPY/TITLE button to return to the main title menu of the disc.• When playing an MP3 disc, press COPY/TITLE button to enable Copy function menu.SUBTITLEWhen playing a disc with multi-language subtitle, press SUBTITLE button continually, the subtitle languages are changed in a circle, and you can select the needed one.ANGLEWhen playing the disc with multi-angle, press ANGLE button to select the view angle.MENU/RIP• When playing DVD disc, press this button once to return to the main menu of the disc.• When playing SVCD, VCD2.0, after the disc is loaded, the unit will display the chapter menu (if PBC is on). Also, you can display this menu by pressing this button.• When a USB is inserted, press this button to enter Ripping menu.() PLAY/PAUSEWhen playing the disc, press button once to pause; press button again to return to normal playback.Cursor buttonsPress cursor buttons to navigate in various menus.Number buttonsPress number buttons to input digits and numbers (e.g. track/chapter number, playback time etc.).ENTERPress ENTER button for confirmation of chosen options.() STOPWhen playing DVD, VCD, CD disc, press button once, the unit will memorize the previous ending point; when afterwards you play the same disc, playback will start from the memorized point. Press button two times, playback will stop without memorizing the stop point. (This function is only active when ON is set for Last Memory item in General setup page.)STEPWhen playing DVD, VCD disc, press STEP repeatedly to play video frame by frame. Press button to resume normal playback. (FAST FORWARD)Press this button for quick forward search. (REWIND)Press this button for quick rewind search./ (PREVIOUS/NEXT)• When playing DVD disc, press button to go to the previous chapter.• When playing VCD, CD disc, press button to go to the previous track.• When playing DVD disc, press button to go to the next chapter.• When playing VCD, CD disc, press button to go to the next track.

89OperationOperationPROG• If the disc contains 2 or more tracks, chapters or titles, set up the playing order to your preference. Press PROG button to enter program menu.• Press number buttons to input the number of the track, title or chapter. Use cursor buttons to move the cursor to START item. Press ENTER button to start program playback. Press PROG button to cancel programming. For MP3 disc, this function is not available.SELECT SOURCEPress this button repeatedly to switch between modes: TUNER => LINE=> DVD.SETUPPress SETUP button to enter or exit the system setup menu.GOTOPress GOTO button to enter goto menu where you can input chapter/title number or disc time. Select an item with cursor buttons, the use digit buttons to input data. Playback will start in accordance with the input data when you press ENTER button.REPEATPress REPEAT button to repeat a title, chapter, track or the whole disc. Available repeat modes vary depending on the disc type being used.V-MODEPress this button to select a video output mode.A - B• Press A-B button at the start point (A) and the ending point (B) to select the repeat fragment.• Press A-B button the third time to cancel fragment repeat and return to normal play.AUDIO• When playing DVD with more than one audio stream, press this button to select the needed language.• When playing a VCD disc, press this button repeatedly to select available audio channels (Left mono/Right mono/Mix mono/Stereo). (MUTE)Press this button, the sound will be turned off. Press the button again, the sound will resume.VOLUME+/-Press VOLUME+ button to adjust volume up. Press VOLUME- button to adjust volume down.OSDPress this button to display various info on the current playback: title/chapter time elapsed/remaining, etc.ZOOMWhen playing DVD, VCD disc, press ZOOM button to zoom in our out the picture. In zoom in mode, press cursor buttons to move the picture for viewing.A-MODEPress this button to switch between 5.1 channel output and stereo output of the sound.S-EFFECTPress this button repeatedly to switch between the available sound effects. You are recommended to switch off the sound effect when playing a Dolby 5.1 channel disc so that to obtain the real 5.1 effect.TONEPress to select BASS or TREBLE, then use VOLUME+/- buttons to control the level of bass or treble.KEY+/-Press these buttons to change the key of the sound.

10OperationCH-LEVELPress this button repeatedly to select a channel or the overall volume, then press VOLUME+/- buttons to adjust its level.System setup1. Press SETUP button to enter the setup menu. In Setup menu, press SETUP button again to quit the setup page.2. Use / buttons to choose a setup page: General setup page, Audio setup page, Dolby setup page, Video setup page, Preference page.3. Press button to enter the setup page selected.4. Use / buttons to select the option you want to adjust.5. Press button to enter the adjustment list. Use / buttons to select the adjustment and press ENTER button to confirm and button to return to options list.6. To return to setup page list press button when in the option list. The items in gray can’t be set up. The setup is memorized and kept after power is off.General setupGeneralGeneral setup pageTV displayAngle markOSD languageClosed captionsScreen saverLast memoryAudioDolbyVideoPreference• TV DISPLAY4:3 PanScan: When the unit connects to the normal TV set, the wide-screen image shows on the full screen, but some part is cut off.4:3 LetterBox: When the unit connects to the normal TV set, the wide-screen image shows and black bars appear on the top and bottom of screen.16:9: Use this item when the unit is connected with the wide screen TV set.• ANGLE MARKIt will show the angle mark when playing DVD disc with multi-angle view if selecting On.• OSD LANGUAGESelect on-screen display language: English, Russian.• CLOSED CAPTIONSThis function doesn’t work with discs without captions. If Caption is Off, press SUBTITLE button on the RC to set Caption on. The default setup is On.• SCREEN SAVERIf Screen saver is set ON and the unit is switched on without a disc playing for several minutes, a moving picture appears on the screen, and the unit will go to standby mode after several minutes. Press POWER button on the RC to wake it up.• LAST MEMORYWhen this function is on, the unit can memorize the time elapsed from the last time you played the disc. Then at the next playing, it will resume playing from the memorized point.Audio setupGeneralAudio setup pageAnalog audioDigital audioChannel delayEqualizer3D processingHDCDKaraoke setupAudioDolbyVideoPreference