Philips HTS5200/12 User manual

1 - 1
HTS5200/12/98/51
©Copyright 2010 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
Published by RY1014 Service Audio Printed in The Netherlands Subject to modification
DVD Home Theater System
Version1.1
TABLE OF CONTENTS
Location of PCB Boards ............................................ 1-2
Versions Variation ...................................................... 1-2
Measurement Setup .................................................. 1-4
Specifications ............................................................ 1-3
Service Aids .............................................................. 1-5
ESD & Safety Instruction .......................................... 1-6
Lead-free soldering Information ................................ 1-7
Setting procedure & Repair Instructions........................ 2
Disassembly Instructions & Service positions .............. 3
Block & Wiring Diagram ................................................ 4
VFD+USB+AUX Board .................................................. 5
Main+LED Board............................................................ 6
Power Board .................................................................. 7
Service Manual
Service
Tfswjdf
Service
Tfswjdf
Service
AMP Board .................................................................... 8
Touch Board .................................................................. 9
Mechanical Exploded view .......................................... 10
Revision List ................................................................ 11
GB
Chapter
3139 785 35301

1 - 2
LOCATION OF PCB BOARDS
VERSION VARIATION:
Type/Versions
Features
HTS5200
Output Power - 400W
Voltage (110~127V)
Voltage (220~240V)
Main+Led Board
VFD+USB+UAX Board
AMP Board
Type/Versions
Board in used
HTS5200
C
C
C
/12
REPAIR SCENARIO MATRIX:
/12
x
x
*C = Component Level Repair
Power Board
C
Touch Board C
C
C
C
/98
C
C
/98
x
x
x
TOUCH PCB
VFD PCB
MAIN PCB
POWER PCB
DOOR LED PCB
LED PCB
MAIN PCB
AUX PCB
AMP PCB
POWER PCB
USB PCB
TOP VIEW BOTTOM VIEW
/51
x
x
C
C
C
/51
C
C

1 - 3
SPECIFICATIONS
Playback media
DVD-Video, DVD+R/+RW, DVD-R/-RW, DVD+R DL,CD-R/CD-
RW, Audio CD, Video CD/SVCD, Picture CD, MP3-CD, WMA-
CD, DivX-CD, USB storage device (for /12/98)
AVCHD, BD-RE, BD-Video, DVD-Video, DVD+R/+RW, DVD-
R/-RW, DVD+R/-RDL, CD-R/CD-RW, Audio CD, Video CD/
SVCD, Picture CD, MP3-CD, WMA-CD, DivX (Ultra)-CD, USB
storage device (for /51)
File Format
Audio ................................................... .mp3, .wma (for /12/98)
Audio ................................................. .mp3, .wma.wav (for /51)
Video ....... .divx, .divx ultra, .mpeg, .mpg, .wmv (simple prole)
..................................................................................(for /12/98)
Video .................... .avi, .divx, .mp4, .mkv, .mov, .wmv (for /51)
Picture .................................................... .jpeg, .jpg (for /12/98)
Picture ................................................... .jpg, .gif, .png (for /51)
Amplifier
Total output power.............................. 400 W RMS (for /12/98)
Total output power............... 1000 W RMS (30%THD) (for /51)
Frequency response................................ 20 Hz-20 kHz / ±3dB
Signal-to-noise ratio.................. > 65 dB (CCIR) / (A-weighted)
Input sensitivity..........................................................................
AUX ....................................................... 1000 mV (for /12/98)
AUX .............................................................. 900 mV (for /51)
MP3 LINK ................................................ 550 mV (for /12/98)
MP3 LINK ..................................................... 500 mV (for /51)
Video
Signal system ........................................................ PAL / NTSC
Component video output ...........................................................
............................... 480i/576i, 480p/576p, 720p, 1080i (for /51)
HDMI output ..............................................................................
.............. 480i/576i, 480p/576p, 720p, 1080i, 1080p (for /12/98)
HDMI output ..............................................................................
.... 480i/576i, 480p/576p, 720p,1080i, 1080p, 1080p24 (for /51)
Audio
S/PDIF Digital audio input .........................................................
Coaxial................................................................ IEC 60958-3
Sampling frequency...................................................................
MP3 ................................................ 32 kHz, 44.1 kHz, 48 kHz
WMA............................................................ 44.1 kHz, 48 kHz
Constant bit rate ........................................................................
MP3 ........................................................ 112 kbps - 320 kbps
WMA......................................................... 48 kbps - 192 kbps
Radio
Tuning range ................... FM 87.5-108 MHz (50 kHz) (for /12)
Tuning range ....... FM 87.5-108 MHz (50/100 kHz) (for /98/51)
Signal-to-noise ratio................................................... FM 50 dB
Frequency respose ..................... FM 180 Hz~12.5 kHz / ±3dB
USB
Compatibility.............................................. Hi-Speed USB (2.0)
Class support........................ UMS (USB Mass Storage Class)
File system ........................................................ FAT16, FAT32
Maximum memory support........................................ < 160GB.
Main Unit
Power supply.............................................................................
Russia/China/India .................................... 220-240V; ~50 Hz
Asia Pacic/Latin America.......................................................
................................110-127V/220-240V; ~50-60Hz switchable
Power consumption..................................... 100 W (for /12/98)
Power consumption.......................................... 135 W (for /51)
Standby power consumption ..................... ≤ 0.3 W (for /12/98)
Standby power consumption .......................... < 0.9 W (for /51)
Dimensions (WxHxD) .......... 434 x 253 x 129 (mm) (for /12/98)
Dimensions (WxHxD) ................. 435 x 58 x 358 (mm) (for /51)
Weight .......................................................... 3.6 kg (for /12/98)
Weight ............................................................. 3.87 kg (for /51)
Speakers
System.......................................................... full range satellite
Speaker impedance...................................... 6 ohm (for /12/98)
Speaker impedance...................................................................
..............................3 ohm (center), 5 ohm (Front/Rear) (for /51)
Speaker drivers ........... 1 x 3” full range + 1” twitter (for /12/98)
Speaker drivers .................................. 2 x 3” full range (for /51)
Frequency response.......................................... 150 Hz-20 kHz
Dimension (WxHxD)..................................................................
..............................................114 x 316 x 114 (mm) (for /12/98)
Center..........................................280 x 95 x 92 (mm) (for /51)
Speaker ...................................100 x 280 x 115 (mm) (for /51)
Tall speaker...........................260 x 1101 x 260 (mm) (for /51)
Weight .......................................................................................
.................................................................... 1.03 kg (for /12/98)
Center............................................................ 1.40 kg (for /51)
Speaker ....................................... 0.98~1.05 kg/each (for /51)
Tall speaker................................. 3.73~3.81 kg/each (for /51)
Cable length ..............................................................................
.......................................................................... 2 m (for /12/98)
Center.................................................................. 3 m (for /51)
Front .................................................................... 4 m (for /51)
Rear................................................................... 10 m (for /51)
Subwoofer
Impedance...................................................................... 3 ohm
Speaker drivers ................... 165 mm (6.5”) woofer (for /12/98)
Speaker drivers ........................... 203 mm (8”) woofer (for /51)
Frequency response........................................... 40 Hz-150 Hz
Dimensions (WxHxD) ............................ 196 x 395 x 342 (mm)
Weight .......................................................... 4.7 kg (for /12/98)
Weight ............................................................. 5.37 kg (for /51)
Cable length ....................................................................... 4 m
Laser specification
Type................. Semiconductor laser GaAIAs (CD) (for /12/98)
Laser Type (Diode)....................................................................
.....InGaN/AIGaN (BD), InGaAIP (DVD), A IGaAs (CD) (for /51)
Wave length...............................................................................
.................650 - 660 nm (DVD), 784 - 796 nm (CD) (for /12/98)
Wave length...............................................................................
....................... 405 +5nm/-5nm (BD), 650+13nm/-10nm (DVD),
................................................ 790 +15nm/-15nm (CD) (for /51)
Output power......... 6 mW (DVD), 7 mW (VCD/CD) (for /12/98)
Output power (Max. ratings)......................................................
....................................... 20mW (BD), 7mW (DVD/CD) (for /51)
Beam divergence................................. 60 degrees. (for /12/98)
Specications subject to change without prior notice.

1 - 4
LEVEL METER
e.g. Sennheiser UPM550
with FF-filter
S/N and distortion meter
e.g. Sound Technology ST1700B
L
R
DUT
CD
Use Audio Signal Disc
(replaces test disc 3)
SBC429 4822 397 30184
Bandpass
250Hz-15kHz
e.g. 7122 707 48001
LF Voltmeter
e.g. PM2534
DUT
RF Generator
e.g. PM5326
S/N and distortion meter
e.g. Sound Technology ST1700B
Use a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz).
Ri=50
Tuner FM
MEASUREMENT SETUP

1 - 5
Service Tools:
Universal Torx driver holder .................................4822 395 91019
Torx bit T10 150mm ...........................................4822 395 50456
Torx driver set T6-T20 .........................................4822 395 50145
Torx driver T10 extended .....................................4822 395 50423
Compact Disc:
SBC426/426A Test disc 5 + 5A ...........................4822 397 30096
SBC442 Audio Burn-in test disc 1kHz .................4822 397 30155
SBC429 Audio Signals disc .................................4822 397 30184
Dolby Pro-logic Test Disc ....................................4822 395 10216
SERVICE AIDS
HANDLING CHIP COMPONENTS

1 - 6
NL
WAARSCHUWING
Alle IC’s en vele andere halfgeleiders zijn
gevoelig voor electrostatische ontladingen
(ESD).
Onzorgvuldig behandelen tijdens reparatie kan
de levensduur drastisch doen verminderen.
Zorg ervoor dat u tijdens reparatie via een
polsband met weerstand verbonden bent met
hetzelfde potentiaal als de massa van het
apparaat.
Houd componenten en hulpmiddelen ook op
ditzelfde potentiaal.
I
AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono
sensibili alle scariche statiche (ESD).
La loro longevità potrebbe essere fortemente
ridatta in caso di non osservazione della più
grande cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere
collegato allo stesso potenziale che quello della
massa dell’apparecchio tramite un braccialetto
a resistenza.
Assicurarsi che i componenti e anche gli utensili
con quali si lavora siano anche a questo
potenziale.
GB
Safety regulations require that the set be restored to its original
condition and that parts which are identical with those specified,
be used.
Safety components are marked by the symbol
!
.
NL
Veiligheidsbepalingen vereisen, dat het apparaat bij reparatie in
zijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen,
identiek aan de gespecificeerde, worden toegepast.
De Veiligheidsonderdelen zijn aangeduid met het symbol
!
.
F
Les normes de sécurité exigent que l’appareil soit remis à l’état
d’origine et que soient utiliséés les piéces de rechange identiques
à celles spécifiées.
Less composants de sécurité sont marqués
!
.
D
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu
beachten. Der Original zustand des Geräts darf nicht verändert werden;
für Reparaturen sind Original-Ersatzteile zu verwenden.
Sicherheitsbauteile sind durch das Symbol
!
markiert.
I
Le norme di sicurezza esigono che l’apparecchio venga rimesso
nelle condizioni originali e che siano utilizzati i pezzi di ricambio
identici a quelli specificati.
Componenty di sicurezza sono marcati con
!
.
GB
After servicing and before returning set to customer perform a leakage
current measurement test from all exposed metal parts to earth ground
to assure no shock hazard exist, The leakage current must not
exceed 0.5mA.
CLASS 1
LASER PRODUCT
3122 110 03420
GB
Warning !
Invisible laser radiation when open.
Avoid direct exposure to beam.
S
Varning !
Osynlig laserstrålning när apparaten är öppnad och spärren
är urkopplad. Betrakta ej strålen.
SF
Varoitus !
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina
näkymättömälle laserisäteilylle. Älä katso säteeseen!
GB
WARNING
A
ll ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
F
ATTENTION
Tous les IC et beaucoup d’autres
semi-conducteurs sont sensibles aux
décharges statiques (ESD).
Leur longévité pourrait être considérablement
écourtée par le fait qu’aucune précaution n’est
prise à leur manipulation.
Lors de réparations, s’assurer de bien être relié
au même potentiel que la masse de l’appareil et
enfiler le bracelet serti d’une résistance de
sécurité.
Veiller à ce que les composants ainsi que les
outils que l’on utilise soient également à ce
potentiel.
ESD
D
WARNUNG
Alle ICs und viele andere Halbleiter sind
empfindlich gegenüber elektrostatischen
Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kan
die Lebensdauer drastisch reduzieren.
Veranlassen Sie, dass Sie im Reparaturfall über
ein Pulsarmband mit Widerstand verbunden
sind mit dem gleichen Potential wie die Masse
des Gerätes.
Bauteile und Hilfsmittel auch auf dieses gleiche
Potential halten.
DK Advarse !
Usynlig laserstråling ved åbning når sikkerhedsafbrydere er
ude af funktion. Undgå udsaettelse for stråling.
F
"Pour votre sécurité, ces documents doivent être utilisés par
des spécialistes agréés, seuls habilités à réparer votre
appareil en panne".
GB
ESD PROTECTION EQUIPMENT
Complete Kit ESD3 (small tablemat, wristband,
connection box, estention cable and earth cable ....... 4822 310 10671
Wristband tester ................................................................. 4822 344 13999

1 - 7
Pb(Lead) Free Solder
When soldering , be sure to use the pb free solder.
INDENTIFICATION:
Regardless of special logo (not always indicated)
one must treat all sets from 1 Jan 2005 onwards,according
next rules:
Important note: In fact also products of year 2004 must
be treated in this way as long as you avoid mixing solder-
alloys (leaded/ lead-free). So best to always use SAC305
and the higher temperatures belong to this.
Due to lead-free technology some rules have to be
respected by the workshop during a repair:
•Use only lead-free solder alloy Philips SAC305 with
order code 0622 149 00106. If lead-free solder-paste
is required, please contact the manufacturer of your
solder-equipment. In general use of solder-paste
within workshops should be avoided because paste is
not easy to store and to handle.
•Use only adequate solder tools applicable for lead-
free solder alloy. The solder tool must be able
– To reach at least a solder-temperature of 400@C,
– To stabilize the adjusted temperature at the solder-
tip
– To exchange solder-tips for different applications.
•Adjust your solder tool so that a temperature around
360@C – 380@C is reached and stabilized at the solder
joint. Heating-time of the solder-joint should not exceed
~ 4 sec. Avoid temperatures above 400@C otherwise
wear-out of tips will rise drastically and flux-fluid will
be destroyed. To avoid wear-out of tips switch off un-
used equipment, or reduce heat.
•Mix of lead-free solder alloy / parts with leaded solder
alloy / parts is possible but PHILIPS recommends
strongly to avoid mixed solder alloy types (leaded and
lead-free).
If one cannot avoid or does not know whether product
is lead-free, clean carefully the solder-joint from old
solder alloy and re-solder with new solder alloy
(SAC305).
•Use only original spare-parts listed in the Service-
Manuals. Not listed standard-material (commodities)
has to be purchased at external companies.
•Special information for BGA-ICs:
–Always use the 12nc-recognizable soldering
temperature profile of the specific BGA (for de-
soldering always use the lead-free temperature profile,
in case of doubt)
–Lead free BGA-ICs will be delivered in so-called ‘dry-
packaging’ (sealed pack including a silica gel pack) to
protect the IC against moisture. After opening,
dependent of MSL-level seen on indicator-label in the
bag, the BGA-IC possibly still has to be baked dry.
(MSL=Moisture Sensitivity Level). This will be
communicated via AYS-website.
Do not re-use BGAs at all.
•For sets produced before 1.1.2005 (except products
of 2004), containing leaded solder-alloy and
components, all needed spare-parts will be available
till the end of the service-period. For repair of such
sets nothing changes.
•On our website www.atyourservice.ce.Philips.com
you find more information to:
• BGA-de-/soldering (+ baking instructions)
• Heating-profiles of BGAs and other ICs used in
Philips-sets
You will find this and more technical information
within the “magazine”, chapter “workshop news”.
For additional questions please contact your local
repair-helpdesk.

2 - 12 - 1
System , Region Code , etc. Setting Produre
6) Upgrading new software
a) Copy the latest upgrading software onto a CD-R or USB storage
device
b) Insert the CD-R program disc or connect the USB storage device
to the home theater
c) TV will show message as follow
d) Select <OK>,the home theater will start to upgrading
automatically
Note: when upgrade in progress, please do not unplug or switch off
the device.
when the updated is complete ,the home theater automatically
switch to standby.
7) Produce to change Tuner grid (for /98)
Only applicable for certain regions, in some countries, the
frequency step between adjancent channels in the FM hand is
50KHZ(100KHZ in some areas)
a) Press<radio> on R/C to select “FM”
b) In “FM” playbak mode,press & hold< play/pause> button until
“grid 9” or “grid 10” appears
Note: repeaing the same action will toggle back to it previous
tunning grid setting.
* “grid 10” is default for /55/98 version.
8)How to replace the defective DVD Loader
a) Remove the defective DVD Loader (see chapter 3).
b) Accordingly connect DVD Loader and “CN802”, “CN803”,
“CN801” on the top of main board as shown below:
CN802
CN801
CN803
CAUTION!
This information is confidential and may not be
distributed.Onlyaqualifiedservicepersonshould
reprogram the Region Code.
Upgrade file detected
Do you wish to continue with
the software upgrade?
OK Cancel
Current model: 5200-12/98/51
Version:00.08.00_1 Release:2009.12.16
Region: 2 Servo:D1.72.01.00
8032: 05.00.04.06 Risc: BB.00.00.00
MCU: 06.01 Touch: 0044 Dock: Error
if current model doesnot match your set,
use down arrow key on the remote to change
OK
c) Remove solder joint on the ESD protection point.
The ESD protection point
on the top side view of OPU
The Top side view of OPU
Note: The ESD protection point on any one side must be soldered if
- the DVD Loader is OK and needs to be disconnected from
connector CN802, CN803 and CN801 of the main board.
- the defective DVD Loader is needed to be send back to supplier
for failure analysis and to support back charging evidence.
1)Restore factory setting
a) Press <SETUP> button on R/C
b) Select <preference setup> ,then press < OK >
c) Select <default>,then press <OK> to conrm
2)Region code change
a) Open the Door,then,press “1” “5” “9” on RC
b) Press <OK> button on RC
c) TV will show message as follow:
d) If current model doesnot match your set, use down arrow key on
the remote to change.
3)Password change
a) Press <SETUP> button on R/C
b) Select <preference setup> ,then press <OK>
c) Select <password> <change>,then press <OK> to conrm
“0000” is default password supplied.
4)Trade model
a) Press <Open/Close>button on R/C
b) Press “2” “5” “9” on R/C,VFD will display “TRA ON “ or “TRA
OFF“
5)Check on software version
a) Press <SETUP> button on R/C
b) Select <preference setup> ,then press <OK>
c) Select <version info>,then press <OK>
d) TV will show message as follow:
Preference setup
Version Info.
Current model: 5200-12/98/51
Version :00.08.00_1 Release: 2009.12.16
Region: 2 Servo: D1 .72.01.00
8032:05.00.04.06 Resc: BB.00.00.00
MCU: 06.01 Touch: 0044
OK
Press SETUP to exit menu

2 - 22 - 2
REPAIR INSTRUCTIONS (One)

2 - 32 - 3
REPAIR INSTRUCTIONS (Two)

2 - 42 - 4
REPAIR INSTRUCTIONS (Three)

3 - 1 3 - 1
DISASSEMBLY INSTRUCTIONS
Dismantling of Rear Panel
1) Using hands to push the cable door to remove it as shown in gure 1.
2) Loosen 2 screws “A” to remove footstand ass’y as shown in gure 2.
3) Loosen 9 screws “B” to remove rear panel as shown in gure 3.
Dismantling of the Main PCB
1) Loosen 8 screws “C” to remove main PCB bracket as shown in gure 4.
2) Loosen 3 screws “D” and loosen 7 screws “E” at the main PCB bracket as shown in gure 5&6 to remove main PCB.
Figure 2
A
PUSH
Figure 1
B
Figure 3
Figure 4
C
Figure 5
D
Figure 6
E

3 - 2 3 - 2
Dismantling of the USB+AUX PCB
1) Loosen 2 screws “F” at the main PCB bracket to remove AUX PCB as shown in gure 7.
2) Loosen 9 screws “G” to remove DVD fan bracket&fan&USB bracket as shown in gure 8.
3) Loosen 2 screws “H” on the USB PCB to remove it as shown in gure 9.
Figure 7
F
H
Figure 9
G
Figure 8
Dismantling of the Power PCB
1) Loosen 6 screws “I” at the power PCB bracket as shown in gure 10.
2) Loosen 4 screws “J” on the power PCB bottom to remove power PCB as shown in gure 11.
I
Figure 10
J
Figure 11
Dismantling of the AMP PCB
1) Loosen 4 screws “K” on the AMP PCB bottom to remove AMP PCB as shown in gure 12.
K
Figure 12

3 - 3 3 - 3
SERVICE POSITIONS
Note:In some service positions the components or copper patterns of one board may risk touching its neighbouring pc boards or
metallic parts. To prevent such short-circuit use a piece of hard paper or other insulating material between them.
Dismantling of the DVD Module
1) Loosen 3 screws “L” at the power PCB bracket bottom to remove DVD module as shown in gure 13.
L
Figure 13
Dismantling of the VFD+LED+DVD LED PCB
1) Loosen 3 screws “M” on the VFD PCB to remove it as shown in gure 14.
2) Loosen 2 screws “N” on the LED PCB to remove it as shown in gure 15.
3) Loosen 2 screws “O” on the door LED PCB to remove it as shown in gure 16.
4) Loosen 2 screws “P” at the DVD door lens ass’y to remove it as shown in gure 17.
5) Loosen 4 screws “Q” at the touch PCB bracket as shown in gure 18
M
Figure 14
N
O
P
Figure 15
Figure 16
Figure 17
Q
Figure 18

4 - 1 4 - 1
BLOCK DIAGRAM

4 - 2 4 - 2
WIRING DIAGRAM
V3
V4
V1
V2

5 - 1 5 - 1
VFD+USB+AUX BOARD
TABLE OF CONTENTS
FTD Display Pin Assignment.............................................................5-1
Circuit Diagram ................................................................................. 5-2
PCB Layout Top & Bottom View........................................................ 5-3
FTD DISPLAY PIN ASSIGNMENT
PIN CONNECTION

5 - 2 5 - 2
CIRCUIT DIAGRAM
C300 A1
C302 A1
C303 A1
C500 B1
C501 B1
C502 B1
C503 B1
C504 B1
C505 B1
C506 B1
C507 B1
C508 B1
C509 B1
C510 B1
C512 B1
C513 B2
C514 C2
C515 C1
C516 C1
C517 C1
C518 C1
C519 C1
C520 C2
C521 C2
C522 C2
C523 A2
C524 A2
C525 A2
C526 A2
C527 A1
C528 A1
CN2 A1
D500 C2
D501 C2
DP500 B1
FB300 A1
FB301 A1
IC500 B1
IC500 B1
JK2 A2
JK300 A1
LD502 B2
Q501 C2
Q502 C2
Q503 C2
Q504 C2
R500 B1
R501 B1
R502 B1
R503 B2
R504 B1
R505 B1
R506 B1
R507 B1
R509 C2
R510 C2
R511 C1
R512 C1
R513 C1
R514 C1
R515 C1
R516 C1
R518 C2
R519 C2
R520 C1
R521 C1
R522 C1
R523 C1
R524 C1
R525 C1
R526 C2
R527 C2
R528 C2
R529 C2
R530 C2
R533 B2
R534 C1
R536 A1
RB3 A2
RB300 A1
RB301 A1
RB503 B2
RB506 C1
RB507 C1
SN500 B1
USB300 A1
ZD500 B1
ZD501 C1
12
12
A
B
C
A
B
C

5 - 3 5 - 3
PCB LAYOUT - TOP VIEW
PCB LAYOUT - BOTTOM VIEW
1 2
1 2
A
B
A
B
12
12
A
B
A
B
C502 A1
C503 A1
C504 A2
C519 A2
C520 A2
C521 A2
DP500 A2
J500 A1
J501 A2
J502 A1
J503 A1
J504 B1
J505 A2
J506 A2
JK1 A1
JK2 B1
JK300 B2
LD502 B2
Q501 A2
Q503 A2
R507 B2
R510 B1
R534 B1
RB3 A1
RB300 B2
RB301 B2
RB503 B1
RB506 A1
RB507 A1
SN500 A1
USB300 B2
C300 B2
C302 B2
C303 B2
C500 A1
C501 A1
C505 A1
C506 B2
C507 A2
C508 A1
C509 A2
C510 A2
C512 A2
C513 A1
C514 A2
C515 B1
C516 B1
C517 A2
C518 A2
C522 A1
C523 A1
C524 A1
C525 A1
C526 A1
C527 A1
C528 A1
CN2 A1
D500 B2
D501 B2
FB300 B2
FB301 B2
IC500 A2
IC500 A2
Q502 A1
Q504 B2
R500 A1
R501 A1
R502 A2
R503 A1
R504 B1
R505 B1
R506 B1
R509 B2
R511 A1
R512 A2
R513 A2
R514 A2
R515 A2
R516 A2
R518 B2
R519 B2
R520 A2
R521 A2
R522 A2
R523 A2
R524 A2
R525 A2
R526 A2
R527 A2
R528 A2
R529 A1
R530 A1
R533 B2
R536 B2
ZD500A1
ZD501A2

6 - 1 6 - 1
MAIN+LED BOARD
TABLE OF CONTENTS
Internal IC Diagram ...........................................................................6-1
Circuit Diagram(part one) .................................................................. 6-2
Circuit Diagram(part two)................................................................... 6-3
PCB Layout Top View .......................................................................6-4
PCB Layout Bottom View .................................................................. 6-5
INTERNAL IC DIAGRAM - MT1389FEX/SN
INTERNAL IC DIAGRAM - A641604L
DVD
PUH
Module
FLASH
Front-panel
Remote DRAM USB2.0/3 in 1 card
reader
MT1389S
HDMI1.2Tx
RGB video
CVBS
8ch Audio
SPDIF
DVB-T