I-bus/Phoenix stingray ii+ User manual

Stingray II+ User's Guide # 095-20079-00 Rev. A

Stingray II+ User's Guide
2
ECopyright 2000
All Rights Reserved
095-20079-00 Rev. A
The information in this document is su ject to change without prior notice in order to improve relia ility,
design and function and does not represent commitment on the part of the manufacturer. In no event will
the manufacturer e lia le for direct, indirect, special, incidental, or consequential damages, or the posĆ
si ility of such damages, arising out of the use of this information.
This document contains proprietary information protected y copyright. All rights are reserved. No part
of this manual may e reproduced y any mechanical, electronic, or other means in any form without
prior written permission of the manufacturer.
Trademarks
IBM PC is a registered trademark of International Business Machines Corporation. Intel and Pentium
are registered trademarks of Intel Corporation. Award is a registered trademark of Award Software, Inc.
Other product names mentioned herein are used for identification purposes only and may e trademarks
and/or registered trademarks of their respective companies.
Customer Service
Headquarters: I-Bus/Phoenix, A Maxwell Technologies Company
9174 Sky Park Court
San Diego, CA 92123
Telephone: [phone] [phone] (in the U.S.)
Direct Sales: [phone]
Tech. Support: (877) 777-IBUS (4287)
FAX: [phone]
E-Mail: [email protected]
sales@i us.com
manuals@i us.com
WEB: www.i us.com
European Headquarters, Israel:
I-Bus/Phoenix
Units 2-3 Kingscroft Court
Ridgway, Havant
Hampshire PO9 1LS, UK
Telephone: [phone]
FAX: [phone]
E-Mail: sales@i us.co.uk
support@i us.co.uk
France, Ital : I-Bus/Phoenix France
B.P. 45 Val onne
06901 Sophia Antipolis CEDEX
France
Telephone: [phone]
FAX: [phone]
E-Mail: ventes.fr@i us.com
support.fr@i us.com
German , Switzerland, Austria
I-Bus/Phoenix Germany
Peter-Henlein-Strasse 4
D-82140 Olching
Germany
Telephone: [phone]
FAX: [phone]
E-Mail: sales@i us-deutschland.de

Stingray II+ User's Guide 3

Stingray II+ User's Guide
4
Dear Customer,
Thank you for purchasing an I-Bus/Phoenix product. We hope
that this product exceeds your expectations. It is our desire to
provide you with accurate, up-to-date information a out the
product(s) you have purchased. We welcome your comments and
suggestions a out our manuals.
You may email those comments and suggestions to
manuals@i us.com. Please e sure to include your name, the
name of your company, the product you purchased, and the manual
num er/revision (i.e. 00-00000-00 Rev. *). This num er is located
on the title page.
At I-Bus/Phoenix, we value our customers and partners, and you
can continue to count on I-Bus/Phoenix to e customer focused
and to provide you a large range of solutions -- from cost-effective
to fully customized industrial computer solutions.
Again, thank you for your committment to I-Bus/Phoenix. We
appreciate your usiness and look forward to continuing to work
with you and helping you reach your goals.

Table of Contents
Stingray II+ User's Guide i
Cha ter 1. Introduction
About this manual 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What is included with this package 1-5. . . . . . . . . . . . . . . . . . . . .
Cha ter 2. Switches and Connectors
Switches 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connectors 2-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cha ter 3. Capability Expanding
System emory 3-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cache emory 3-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Change CPU 3-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cha ter 4. Award BIOS Setup
Entering Setup 4-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Keys 4-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Getting Help 4-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The ain enu 4-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard C OS Setup 4-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BIOS Features Setup 4-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chipset Features Setup enu 4-14. . . . . . . . . . . . . . . . . . . . . . . .
Power anagement Setup 4-18. . . . . . . . . . . . . . . . . . . . . . . . . . .
PnP/PCI Configuration 4-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Integrated Peripherals 4-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supervisor/User Password Setting 4-28. . . . . . . . . . . . . . . . . . . .
IDE HDD Auto Detection 4-29. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power On Boot 4-33. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BIOS Reference-POST essage 4-34. . . . . . . . . . . . . . . . . . . . .
BIOS Reference-POST Codes 4-38. . . . . . . . . . . . . . . . . . . . . . .
BIOS Default Drive Table 4-44. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents
Stingray II+ User's Guide
ii
A endix 1. Watch Dog Ti er
Watch Dog Timer A1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watch Dog Timer Control Register A1-2. . . . . . . . . . . . . . . . . . . .
Watch Dog Timer Programming Procedure A1-3. . . . . . . . . . . .
A endix 2. Me ory Mapping
A endix 3 - Li ited Warranty
A endix 4 - FCC Infor ation

Chapter 1 - Introduction
Stingray II+ User's Guide 1-1
About This Manual
This manual is written to help you use the Stingray II+. A single manual
is used to cover both the Stingray II+ and the Stingray II. Stingray II
users should simply disregard references to SCSI, VGA, and Ethernet.
The manual describes how to arrange various settings on the Pentium
CPU board to meet your requirements. It is laid out as follows:
Chapter 1, Introduction" gives an overview of the product`s
specifications. It also tells you what is included in the product package.
Chapter 2, Switches and Connectors" describes the definitions and
positions of Jumpers and Connectors that you may easily configure and
set up per your requirement.
Chapter 3, Capability Expanding" describes how to change or expand
the CPU Board by changing the system memory, cache memory, and
CPU to get more power out of the CPU board.
Chapter 4, Award BIOS Setup" describes how to use the advanced
PCI/Green BIOS to control almost every feature, including the watchdog
timer.
Appendix 1 describes how to set up the Watch Dog Timer (WDT) and
gives an example of how to program the WDT.
Appendix 2 describes the memory mapping of the Stingray II for user's
reference.
Appendix 3 is the manufacturer's limited warranty
Appendix 4 covers the FCC information related to the Stingray II

Chapter 1 - Introduction
Stingray II+ User's Guide
1-2
S ecifications
DSystem Architecture
GFull size SBC with PCI/ISA connectors
GIntel dual Socket 370 Pentium III / Celeron with 66/100 Hz
FSB
GPCI V2.1 compliant
GPIC G 1.0 (Rev.2.0) compliant
GIntel PS1.1 specification compliant
DCPU Support
GIntel Intel Pentium III / Celeron CPU with 256/128K cache on
die
GBrand New Socket 370 FC-PGA CPU running at 66/100 Hz
FSB up to 850 Hz
GDual CPU support
GSupports streaming SI D instruction
GOn board intelligent switching type power regulator ×2
DMain Memory
GSupport SDRA up to 1GB ( ax.)
G168 pin DI socket ×4
GECC support (single bit error correction/ ultiple bit errors
reporting)
DBIOS
GAward System BIOS
GPlug & Play support
GAdvanced Power anagement support
GAdvanced configuration & Power Interface support
G2 b flash RO
DChip Set
GIntel 82440BX AGP set
G66/100 Hz FSB support
GPCI V2.1 complied
GOptimized SDRA support

Chapter 1 - Introduction
Stingray II+ User's Guide 1-3
DOn Board VGA (Stingray II+ only
GC&T 69000 AGP mode VGA controller
GTFT LCD/DSTN LCD/CRT control
G2 B SDRA on die
Gaximum Res. Color & Refresh Rate
Resolution Colors Refresh Rate (Hz)
1280×1024 256 60
1024×768 16bits (High color) 85, 75, 65
800×600 24bits (True color) 85, 75, 65
GDriver support:Windows 95/98, Windows NT4.0
G15 pin CRT connector ×1, 50 pin LCD panel connector ×1
DOn Board LAN (Stingray II+ only
GIntel 82559 Single Ethernet controller
G10 Base T/100 Base TX support, full duplex
GComplied with PCI V2.1, IEEE802.3, IEEE 802.3U
GBackward compatible with former 82558 Ethernet controller
base net modules
GDriver support: DOS/Windows, Windows 95/98, Windows
NT4.0, Netware, SCO Open Server 5.0
GRJ45 connector ×1
DOn Board SCSI Socket (Stingray II+ only
GAdaptec 7880 SCSI controller (EBK SCSI odule)
GDriver support: Windows 95/98, Windows NT4.0, SCO Open
Server 5.0
DOn Board I/O
GWinbond W83977 Super I/O on board
GSIO ×2, with 2×16C550 UARTs, 9 pin D-type ×1, 10 pin HEADĆ
ER ×1(may be configured as RS422/485)
GPIO ×1, Bi-directional, EPP/ECP support, 26 pin ×1
GFloppy Disk controller: 5.25″ 360K/1.2 B, 3.5″
720K/1.2 B/1.44 B/2.88 B support, 34 pin connector ×1
GOn chip enhanced IDE ×2, PIO up to mode 4, D A master up
to mode 2, Ultra D A/33 support, 40 pin ×2, total 4 EIDE DeĆ
vice support

Chapter 1 - Introduction
Stingray II+ User's Guide
1-4
GOn chip keyboard, mouse controller, PS/2 keyboard, 6 pin mini
DIN ×1, 5 pin header ×1, PS/2 mouse,
6 pin mini DIN ×1
GOn board USB port ×2 (6 pin header ×1)
GOn board buzzer ×1
GOn board 2 pin header for reset SW, 4 pin for speaker, 5 pin for
keylock
GAdditional power connector: 4 pin male power connector on
board
GOn board 2 pin header for I2C
DOn Board RTC
GHigh precision real time clock/calendar with battery back up
DOn Board Solid State Disk Socket
GOn board reserved socket for DiskOnChip of -sysĆ
tems:2 B~144 B, etc
DSystem Monitor
GWinbond W83782D system monitor controller
GSeven voltages (For +3.3V, +5V, +12V, −12V, Vtt and Vcore
×2)
GTwo Fan speeds (For CPU)
GThree temperatures
GDrivers support: Windows 95/98, Windows NT4.0
DISA Support
Gaximize ISA signals to support ISA cards up to 20
DWatchdog Timer
G1,2,4…64 seconds time-out intervals
DDimensions
G340mm(D) × 122mm(W)
DPower Requirements
G+5V:20A ( ax.)
G+12V: 400mA ( ax.)
G-12V: 50mA ( ax.)

Chapter 1 - Introduction
Stingray II+ User's Guide 1-5
DEnvironments
GOperating temperatures:0_C to 60_C
GStorage temperatures:-20_C to 80_C
GRelative humidity:10% to 90% (Non-condensing)
DCertification
GCE approval
GFCC Class A
What is included with this ackage
In addition to this manual, the STINGRAY II+ package includes the
following items
GSTINGRAY II+ (or STINGRAY II) single board computer x 1
GPrinter and Series Port cable x 1
GFDC cable x 1
GIDE cable x 1
G5 pin to 5 pin keyboard cable x 1 (for DIN keyboard connector)
GEBK-SCSI (7880) add-on Card × 1(STINGRAY II+ only)
GVGA C&T 69000 driver × 1 (STINGRAY II+ only)
GIntel 82559 driver × 2 (STINGRAY II+ only)
GAdaptec 7880 driver × 3 (STINGRAY II+ only)
If any of these items are missing or damaged, please contact your venĆ
dor or technical support.

Chapter 1 - Introduction
Stingray II+ User's Guide
1-6
This age was intentionally left blank

Chapter 2 - Switches and Connectors
Stingray II+ User's Guide 2-1
This chapter gives the definitions and shows where to locate the posiĆ
tions of switches and connectors.
Switches
Switches on the CPU board are used to select options for different funcĆ
tions used. The switch-on or off is to accommodate the variations of the
following table.
Figure 2-1. Switch Positions

Chapter 2 - Switches and Connectors
Stingray II+ User's Guide2-2
Switch Setting Table (*: default setup
CPU Frequency
S1.1 S1.2 S1.3 S1.4 S1.5 S1.6 S1.7
*100 OFF OFF ON OFF OFF OFF OFF
66 ON ON ON OFF OFF ON OFF
CPU Pipelined
S1.8
*Enabled OFF
Disabled ON
DiskOnChip
S2.1 S2.2 S2.3
Disabled OFF X X
C0000 ON ON ON
C8000 ON ON OFF
D0000 ON OFF ON
*D8000 ON OFF OFF
BIOS Fresh
S2.4
Enabled ON
*Disabled OFF
RTC Clear
S2.5
Enabled ON
*Disabled OFF

Chapter 2 - Switches and Connectors
Stingray II+ User's Guide 2-3
COM1 RS232 /RS485/RS422
S4.1 S4.2 S4.3 S4.4 S4.5 S4.6
*RS232 OFF ON OFF ON OFF ON
RS485 ON OFF ON OFF ON OFF
RS422 ON OFF ON OFF ON OFF
COM1 RS232 /RS485/RS422
S4.7 S4.8 S3.1 S3.2 S3.3
*RS232 OFF ON ON OFF OFF
RS485 ON OFF OFF OFF ON
RS422 ON OFF OFF ON OFF
Panel Type
SW1.4 SW1.3 SW1.2 SW1.1
On On On On 1024x768 Dual Scan STN Color Panel
On On On Off 1280x1024 TFT Color Panel
On On Off On 1024x768 Dual Scan STN Color Panel:
On On Off Off 1024x768 Dual Scan STN Color Panel
On Off On On 640x480 Sharp TFT Color Panel
On Off On Off 640x480 18Bit TFT Color Panel
On Off Off On 1024x768 TFT Color Panel
On Off Off Off 800x600 TFT Color Panel
Off On On On 800x600 TFT Color Panel
*Off On On Off 800x600 TFT Color Panel
Off On Off On 800x600 Dual Scan STN Color Panel
Off On Off Off 800x600 Dual Scan STN Color Panel
Off Off On On 1024x768 TFT Color Panel
Off Off On Off 1280x1024 Dual Scan STN Color Panel
Off Off Off On 1024x600 Dual Scan STN Color Panel
Off Off Off Off 1024x600 TFT Color Panel
Panel Director
SW2.1 SW2.2 SW2.3 SW2.4
PCLK From PCLK ON OFF X X
* PCLK From OFF ON X X
DE From X X ON OFF
*DE From LP X X OFF ON

Chapter 2 - Switches and Connectors
Stingray II+ User's Guide2-4
SMI Director
SW3.1 SW3.2
*PIIX4_S I OFF ON
APIC_S I ON OFF
Flash ROM Size
SW3.3 SW3.4
1 ON OFF
*2 OFF ON
Socket 370 CPU Select
SW4.1 SW4.2 SW4.3 SW4.4
Celeron OFF ON OFF ON
Pentium III ON OFF ON OFF

Chapter 2 - Switches and Connectors
Stingray II+ User's Guide 2-5
Connectors
Jumper/Connector define
Connector Function Remark
J1,J8 CPU Fan Header
J2,J3,J4,J5 DI Socket
J7 Speaker Connector
J9 Reset Connector
J10 HDD Connector (Primary)
J11 HDD Connector (Secondary)
J12 Panel Connector
J13 CO 2
J14 FDD Connector
J15 Parallel Connector
J16 USB Connector
J17 LAN Connector
J18 CRT Connector
J19 OUSE Connector
J20 CO 1
J21 KB/ S Connector
JP1,JP6,JP9 Temperature Connector
JP2 Key Lock
JP3 S BUS Connector
JP4 LAN Link LED
JP5 IR Connector
JP7 LAN Speed LED
JP8 LAN Active LED
JP10 HDD LED
JP11 PCI Connector
JP12 Keyboard Connector
JP14 Panel Voltage Connector
U16 DiskOnChip Socket

Chapter 2 - Switches and Connectors
Stingray II+ User's Guide2-6
Pin definitions of connectors
J1, J8: CPU Fan Header Connector
PIN No. Description
1 GND
2 +12V
3 Sense
J7: Speaker Connector
PIN No. Description
1Speaker Signal
2 Ground
3 Ground
4 +5V
J9: Reset Connector
PIN No. Description
1 Reset
2 Ground

Chapter 2 - Switches and Connectors
Stingray II+ User's Guide 2-7
J10, J11: HDD Connector
PIN No. Description PIN No. Description
1 Reset# 2 Ground
3 Data 7 4 Data 8
5 Data 6 6 Data 9
7 Data 5 8 Data 10
9 Data 4 10 Data 11
11 Data 3 12 Data 12
13 Data 2 14 Data 13
15 Data 1 16 Data 14
17 Data 0 18 Data 15
19 Ground 20 N/C
21 D A REQ 22 Ground
23 IOW# 24 Ground
25 IOR# 26 Ground
27 IOCHRDY 28 N/C
29 D A ACK 30 Ground
31 Interrupt 32 N/C
33 SDA 1 34 N/C
35 SDA 0 36 SDA 2
37 HDC CS1# 38 HDC CS3#
39 HDD Active# 40 Ground

Chapter 2 - Switches and Connectors
Stingray II+ User's Guide2-8
J12: Flat Panel Connector
PIN No. Description PIN No. Description
1 ENABLK 2 +12VSAFE
3 LP 4 DE
5 SHFCLK 6 FL
7 P0 8 VDD
9 P2 10 P1
11 P4 12 P3
13 P6 14 P5
15 P8 16 P7
17 P10 18 P9
19 P12 20 VDD
21 P14 22 P11
23 Ground 24 P13
25 P16 26 P15
27 P18 28 P17
29 P20 30 ENAVEE
31 P22 32 P19
33 Ground 34 P21
35 P24 36 P23
37 P26 38 P25
39 /PCLK 40 Ground
41 P28 42 P27
43 P30 44 P29
45 P32 46 P31
47 P34 48 P33
49 Ground 50 P35