ICE N'GO EZ RINK 2.0 User manual

HAVE A QUESTION?
CALL US!
OUR CUSTOMER SERVICE ASSOCIATES ARE
READY TO ANSWER ANY QUESTIONS, CONCERNS
OR COMMENTS YOU MAY HAVE ABOUT YOUR
NEW ICE N’GO RINK KIT.
1-844-797-8305
MONDAY TO FRIDAY, 8 A.M. –5 P.M.
VISIT OUR WEBSITE!
WWW.ICENGO.COM
WWW.ICENGO.CA
WE’D LOVE TO SEE
YOUR FINISHED RINK!
SHARE IT WITH US!
facebook.com/icengorink
instagram.com/icengorink
BACKYARD RINK KIT USER MANUAL
CREATE HOME ICE ADVANTAGE
5743 Ferrier St
Mont-Royal, QC
H4P 1N3

PAGE 1OF 4WWW.ICENGO.COM 1-844-797-8305
WHAT’S INCLUDED:
•BIG WHITE TUBES [1]
•SMALL WHITE TUBES [2]
•BLUE COPING STRIPS [3]
•BLUE COPING CORNERS [4]
•BLUE COPING C-CLIPS [5]
•RED SUPPORT BRACKETS [6]
•WHITE FOAM CORNERS [7]
•STYROFOAM (NOT SHOWN)
•LINER (NOT SHOWN)
•HOCKEY PUCKS (NOT SHOWN)
•LINER TAPE (NOT SHOWN)
RECOMMENDED TOOLS:
•UTILITY KNIFE
•SPIRIT LEVEL
•TAPE MEASURE
•RAKE
•WEIGHTS
STEP 1:
•SEPERATE ALL TUBES AND COPING STRIPS.
EVERYTHING MUST BE PULLED OUT OF THE
LARGE TUBES AND SET APART.
STEP 2:
PLEASE READ THE INSTRUCTIONS CAREFULLY
BEFORE STARTING.
•CHOOSE A LOCATION THAT IS RELATIVELY FLAT
AND CLEAR IT OF DEBREE THAT MAY
PUNCTURE YOUR LINER USING A RAKE
(BRANCHES, ROCKS, PINECONES, ETC.)
•PROCEED TO LAYOUT ALL THE PARTS
ACCORDING TO YOUR RINK SIZE AND MAKE
SURE YOU HAVE ALL THE NECESSARY PARTS.
•IF ANYTHING IS MISSING OR YOU RECEIVED A
WRONG LINER SIZE, PLEASE CALL
1-844-797-8305.
STEP 3:
•INSERT THE BIG TUBE INTO THE SIDE OF THE
BRACKET MARKED “BIG TUBE”.
•DO THIS FOR ALL THE BIG TUBES.
PLEASE READ INSTRUCTIONS CAREFULLY
BEFORE STARTING
[2]
[1]
[3]
[4]
[5]
[6]
[7]

PAGE 2OF 4WWW.ICENGO.COM 1-844-797-8305
STEP 4:
•INSERT ALL THE SMALL TUBES INTO THE SIDE
OF THE BRACKET MARKED “SMALL TUBE”.
•DO THIS FOR ALL THE SMALL TUBES.
STEP 5:
•YOU SHOULD NOW HAVE FOUR COMPLETE
SIDES.
*MODEL SHOWN IS FOR REFERENCE ONLY, SIZING
WILL VARY DEPENDING ON THE KIT SIZE
PURCHASED.
STEP 6:
•AT EACH CORNER INSERT A FLEXIBLE FOAM
FITTING INTO EACH END.
•USE A TWISTING MOTION FOR BEST RESULTS.
STEP 7:
•ENSURE THAT YOUR FRAME IS SQUARE BY
MEASURING FROM CORNER TO CORNER. BOTH
MEASUREMENTS SHOULD BE APPROX. THE
SAME VALUE.
•PLEASE SEE THE CHART ON OUR WEBSITE FOR
THE DIAGONAL MEASUREMENT FOR YOUR
RINK SIZE.
*

PAGE 3OF 4WWW.ICENGO.COM 1-844-797-8305
**
4”
”
STEP 8:
•USING THE INCLUDED FOAM AND A SPIRIT
LEVEL (NOT INCLUDED), LEVEL OUT THE FRAME
STARTING FROM THE HIGHEST POINT
TOWARDS THE LOWEST POINT.
•ENSURE THAT THE GROUND SPIKES ARE FIRMLY
PLANTED INTO THE FOAM OR INTO THE
GROUND.
•PLEASE NOTE ADDITIONAL FOAM FOR
LEVELING MAY NEED TO BE PURCHASED AT
YOUR LOCAL HARDWARE STORE.
MAX SLOPE OF 4 INCHES.
STEP 9:
•LAY OUT THE LINER AND ENSURE THAT IT
OVERLAPS THE FRAME.
•USE WEIGHTS OR SNOW IN EACH CORNER TO
HELP HOLD THE LINER.
•USE CAUTION TO AVOID DAMAGE TO THE
LINER.
INSTALL LINER IN CONDITIONS WHERE THERE IS
LITTLE OR NO WIND.
STEP 11:
•STRETCH THE BLUE COPING STRIPS OVER THE
LINER AND FRAME TO FASTEN THE LINER INTO
PLACE.
STEP 10:
•STRETCH THE BLUE COPING C-CLIPS OVER THE
LINER AND OVER TOP OF THE RED BRACKET.
**LINER SHOWN TRANSPARENT FOR CLARITY.
MAX SLOPE OF 4 INCHES. IF SLOPE IS
GREATER THAN 4 INCHES PLEASE CONTACT
US AT 1-844-797-8305
INSTALL LINER IN CONDITIONS WITH LITTLE
OR NO WIND

PAGE 4OF 4WWW.ICENGO.COM 1-844-797-8305
5”
”
MAX FILL HEIGHT OF 5 INCHES. IF FILLING
PAST 5 INCHES IS NECESSARY, PLEASE
CONTACT US AT 1-844-797-8305
1-844-797-8305
STEP 12:
•INSTALL THE FOUR BLUE CORNERC COPING
PIECES.
STEP 13:
•THE RINK STRUCTURE IS NOW COMPLETE.
STEP 14:
•BEGIN FILLING YOUR RINK AS SOON AS IT IS
COMPLETED.
•ENSURE THAT YOUR HOSE IS FACING THE
GROUND AND NOT CREATING A CURRENT
TOWARDS SIDES.
•FOR BEST RESULTS BUILD YOUR ICE IN 1 INCH
INCREMENT LAYERS AND ALLOW ENOUGH
TIME FOR THE ICE TO FREEZE BETWEEN
LAYERS.
•PLEASE REFER TO THE FREEZING CHART ON
OUR WEBSITE FOR MORE INFORMATION.
MAX FILL HEIGHT OF 5 INCHES.
DO NOT LEAVE RUNNING WATER UNATTENDED