Ice PORTABLE FRIDGE Series User manual
E
MINI SERIES 15L / 20L / 30L
ELITE S SERIES 40L / 50L
•The installation of DC power source in the boat must be handled by qualified
electricians if applicable.
•Ensure connecting th e power to the suitable voltage socket.
•Before switching on the fridge, ensure the fridge has sit in the upright position
for at least 3 hours.
•Always keeping the fridge in upright position during operation. The tilt angle must
be less than 5° and not exceeding 45° for a short period of time.
•Good ventilation: the fridge must be well ventilated for heat dissipation and
maintain some space around the unit.
(Near the vents leave Back Space ≥200mm, Side Space≥100mm)
•Avoid heat source: the fridge should be placed somewhere well-ventilated and
away from heat source, avoid direct sunlight.
•Keep it stable: Do not turn the fridge upside down for drainage. Do not expose it
to rain or operate near water.
NOT SUPPORTED
ELITE T SERIES 36L / 50L / 60L
ELITE S SERIES 75L / 100L
Manual Revision: 2019-02A
Statement! All contents in this manual are copyrighted under IceCube
Coolers LLC Wilmington DE ZIP 19899 U.S. Do not make copies or
distributing any copyright materials without seeking consent of the
rightful owner.
www.icecubecoolers.com, All Rights Reserved IceCube Coolers LLC.
The fridge is not working:
•Check if power supply has malfunctioned or not.
•Check whether the plug or socket is loose.
•Check if the fuse has blown.
•Check if the switch is on or not.
•Compressor may have entered protection mode by delaying startup for 3mins.
Food is frozen:
•The temperature is set too low.
Water flowing sound is inside the fridge:
•It is the flowing sound of refrigerant which is normal.
There are water droplets around the fridge casing or lid gap:
•When moisture in the air meets the lower temperature inside the fridge, it will
naturally cause condensation to form moisture. This is a normal.
The compressor is slightly noisy when starting:
•The noise will be less audible when the compressor stabilizes the cooling
throughout its operation.
Code F1 displayed:
•This is the protection mode to shut off the unit due to low battery voltage. This
can be solved by setting battery protection from H to M or from M to L
Code F2 displayed:
•This is the protection mode to shut off the unit due to fan overload. Please turn
the unit off and restart it after 30mins.
Code F3 displayed:
•This is the protection mode to shut off the unit due to excessive running load of
compressor. Please turn the unit off and restart it after 30 minutes.
Code F4 displayed:
•This indicates the compressor is overloaded or working at a too low speed. Please
turn the unit off and restart it after 30mins.
Code F5 displayed:
•This indicates the compressor has overheated. Move the fridge to a well-
ventilated area an d restart it after 30mins.
Code F6 displayed:
•This indicates unknown parameters were detected by the controller. Please restart
the unit.
Code F7 or F8 displayed:
•This indicates error in reading from temperature sensor. Please check the
sensor terminals.
If the code persists, please contact IceCube Support on
PORTABLE FRIDGE SERIES
ENGLISH INSTRUCTIONS MANUAL
Mobile APP Control by Bluetooth
I O S & A n d r o i d
Please read this operating manual carefully before operating the unit.
Keep manual in a safe place for future reference.
D
C
Troubleshooting
A
Operating Manual
Safety Instructions
Refer to the table for panel type and model
B
Operating Panel & APP
Power Switch
Settings
(-20) Set Temperature
(℃/℉) Temperature Unit
(13.5v) Voltage
(H.M.L) Vehicle voltage
Protection Mode
( )Battery Power
(MAX.ECO) Running Mode
Decrease Temperature
Increase Temperature
USB Port for power supply
D
MINI SERIES 15L / 20L / 30L
•Press button to switch ON/OFF.
•Press or for temperature setting.
•Press setting and choose ECO (Energy-saving) or MAX (Fast
cooling). Factory setting is MAX.
•Long press for three seconds. When H flashes on the screen,
select three battery protection modes H (High), M (Middle) and L (Low)
by pressing setting button again. Factory setting is H.
Handle and wheels of 30L model
can be removed if not needed.
ELITE S SERIES 40L / 50L
•Press button to switch ON/OFF.
ELITE T SERIES 36L / 50L / 60L
•Long press button for three seconds to switch ON/OFF.
•Press or for temperature setting. The temperature of the left
carton must not be lower than that of the right carton
•Press setting and choose ECO (Energy-saving) or MAX (Fast cooling).
Factory setting is MAX.
•Long press for three seconds. When H flashes on the screen, select
three battery protection modes H (High), M (Middle) and L (Low) by
pressing setting button again. Factory setting is H.
•APP type: Press setting button after AP is displayed on the panel
when connecting with APP via Bluetooth
•Icons under the screen: Left Zone: Right Zone
•Press upper at the same time for three seconds to switch
on/off the left zone.
•The left compartment temperature controller will be disabled
when the divider is removed. (two zones are merged) and
temperature control is accessed via the main controller only.
Detachable divider
•The Bluetooth APP function is only available on selected models only.
•Press or for temperature setting.
•Press setting and choose ECO (Energy-saving) or MAX (Fast cooling).
•Built-in battery is not supported for all models.
Factory setting is MAX.
•Long press for three seconds. When H flashes on the screen, select
three battery protection modes H (High), M (Middle) and L (Low) by
pressing setting button again. Factory setting is H.
Dual lid opening of 40L / 50L: Phillip
screwdriver is needed to adjust lid
opening direction
NOT SUPPORTED
•Press button to switch ON/OFF. Long press for three seconds to
unlock.
•Press or for temperature setting.
•Press setting and choose ECO (Energy-saving) or MAX (Fast cooling).
Factory setting is MAX.
•Long press for three seconds. When H flashes on the screen, select
three battery protection modes H (High), M (Middle) and L (Low) by
pressing setting button again. Factory setting is H.
•APP type: Press setting button after AP is displayed on the panel
when connecting with APP via Bluetooth.
ELITE S SERIES 75L / 100L
•Press button to switch ON/OFF.
•Light button
•Press + or –for temperature setting.
•Press setting button (Compressor Speed) and
choose ECO (Energy-saving) or MAX (Fast cooling),
Factory setting is MAX.
•Long press setting button (Battery Protection)
for three seconds. When H flashes on the screen,
select three battery protection modes H (High), M
(Middle) and L (Low) by pressing setting button
again. Factory setting is H.
•L-Box is the left zone; R-Box is the right zone of
both left and right zone are used to adjust
temperature respectively.
75L has single zone and
100L has double zones
APP Connection Instruction: Download the APP from the App store or Google Play.
Connect the fridge to mobile device via switching on the Bluetooth and open the
APP on the device. Search for the equipment, choose the fridge discovered by the APP
and there will be 'AP' shown on the fridge display panel. Press setting button to
connect to the device.
•Accessories are optional add-ons available as separate purchases.
•All models can be supported by the external portable battery pack as an
optional add-on.
•Extra DC/AC cords and adaptors are available as purchasable options.
•Respective plug types are supplied depending on the region sold in.
Adaptor DC power cord Portable battery
•Power: AC 100-240V (equipped with adaptor).
•DC 12/24V (Compatible with universal DC power outlet).
•Never operate battery powered operations near fire or any hazardous environment or
surroundings.
Accessory Photos
Operating Method
Operating Description Panel of different models (Photos are for reference only)
B
C
A
E
This manual suits for next models
3
