ICP DAS USA GW-7473 User manual

GW-7473
GW-7473 QUICK START
The package includes the following items:
Install GW-7473 Utility:
The software is located at:
Fieldbus_CD:\EtherNetIP\Gateway\GW-7473\Utility
http://ftp.icpdas.com/pub/cd/fieldbus_cd/ethernetip/gateway/gw-7473/utility/
Software CD
Quick Start
(This Document)
GW-7473
English/ June 2014/ Version 1.0
1
GW-7473 Quick Start
What’s in the shipping package?
Installing software on your PC
CA-002
(DC connector to
2-wire power cable)

1. Make sure your PC has workable network settings.
2. Disable or well configure your Windows firewall and anti-virus
firewall first.
3. Check Init/Run DIP switch if it is on
Run position.
4. You can make Modbus RTU
connections between PC and GW-
7473 with RS-485/RS-422
converter。
5. Connect both the GW-7473 and your computer to the same
sub network or the same Ethernet switch, and power the GW-
7473 on. GW-7473 also supports to PoE connections. Users
can make a PoE connection with a PoE switch.
2
GW-7473 Quick Start
Connecting the Power and Host PC

1. Double click the GW-7473 Utility shortcut on the desktop.
2. Select the connection interface Modbus RTU or Modbus TCP
3. Click “connect”to open “Diagnostic Window”
3
GW-7473 Quick Start
GW-7473 Utility

Ethernet and Modbus RTU
1. On the Diagnostic window, users can modify the Ethernet and
Modbus RTU parameters with “Scanner Settings”.
2. Ethernet Configurations: “Static IP Address”, “Subnet Mask”
and “Default Gateway”. The default Ethernet settings are
shown below.
Item
Settings (Init Mode)
IP
192.168.255.1
Gateway
192.168.0.1
Mask
255.255.0.0
3. Modbus RTU Configurations: “Net ID”, “Baud Rate”, “Data
Bits”, “Stop Bits”and “Parity”，The default Modbus settings
are shown below.
4. Click “Submit”to finish the configurations.
Item
Settings (Init Mode)
Net ID
1
Baud Rate
115200
Data Bits
8
Stop Bits
1
Parity
None
GW-7473 Configurations
4
GW-7473 Quick Start

EtherNet/IP Adapter
1. Users can set the EtherNet/IP adapter information to the GW-
7473 with “Adapter Settings”window. There are “Static IP
Address”, “Input Instance”and “Output Instance”.
2. Click “Add”to add a new EtherNet/IP adapter information to
the menu. Click “Edit”to modify the menu. Click “Del”to
remove the adapter information on the menu. Click “Submit”
to save the configurations.
3. GW-7473 will connect to the EtherNet/IP adapter
automatically after rebooting.
5
GW-7473 Quick Start

1. On the Modbus Command window, users can modify the
Modbus command. Click “Add”to add a Modbus Command to
the menu. Click “Remove”to remove the command on the
menu.
2. Click “START”to send Modbus command. Click “STOP”to
finish the process.
Modbus Command
6
GW-7473 Quick Start

Related Information
GW-7473 Product page:
http://www.icpdas.com/products/Remote_IO/can_bus/GW-7473.htm
GW-7473 Documentations:
Fieldbus_CD:\EtherNetIP\Gateway\GW-7473\Manual
http://ftp.icpdas.com/pub/cd/fieldbus_cd/ethernetip/gateway/gw-7473/manual/
GW-7473 Utility:
Fieldbus_CD:\EtherNetIP\Gateway\GW-7473\Utility
http://ftp.icpdas.com/pub/cd/fieldbus_cd/ethernetip/gateway/gw-7473/utility/
GW-7473 firmware:
Fieldbus_CD:\EtherNetIP\Gateway\GW-7473\firmware
http://ftp.icpdas.com/pub/cd/fieldbus_cd/ethernetip/gateway/gw-7473/firmware/
IC P DAS Web Site: http://www.icpdas.com
Contact Us (E- Mail): Se [e-mail]
Copyright @ 2014 by ICP DAS Co., Ltd. All Rights Reserved.
7