ICPDAS PEX-P32C32 Series User manual

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.
1
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
The package includes the following items:
One PEX-P32C32 or PISO-P32C32U (-5V) PCI Board.
One Software Utility CD (V5.2 or later)
One Quick Start Guide (This Document)
One CA-4037B Cable
Two CA-4002 D-Sub connectors
Step 1: Setup the Windows driver. The driver is located at:
The UniDAQ driver supports 32-/64-bit Windows 2K/XP/2003/Vista/7/8; it
is recommended to install this driver for new user:
CD: \NAPDOS\PCI\UniDAQ\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
The PISO-DIO Series classic driver supports Windows 98/NT/2K and 32-bit
XP/ 2003/ Vista/7/8. Recommended to install this driver for have been
used PISO-DIO series boards of regular user, please refer to :
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/piso-dio/manual/quickstar
t/classic/
For PEX-P32C32
PISO-P32C32U Series
What’s in the shipping package?
Installing Windows Driver
English/ Oct. 2013/ Version 1.3

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.
2
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Step 2: Click the “Next>”button to start the installation.
Step 3: Check your DAQ Card is or not on supported list, then click the
“Next>”button.
Step 4: Select the installed folder, the default path is C:\ICPDAS\UniDAQ ,
confirm and click the “Next>”button.
Step 5: Check your DAQ Card on list, then click the “Next>”button.
Step 6: Click the “Next>”button on the Select Additional Tasks window.
Step 7: Click the “Next>”button on the Download Information window.
Step 8: Select “No, I will restart my computer later”and then click the
“Finish”button.
For detailed information about the driver installation, please refer to Chapter
2.1 “Getting the UniDAQ Driver DLL Installer package”of the UniDAQ SDK
user manual.
Please make sure JP1 and JP2 jumper is kept in default setting before self-test,
as follows: ( This example uses this power supply.)
Jumper
JP1/JP2
Internal Power

External Power
(Default Setting)
Jumper Setting

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.
3
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Step 1: Shut down and power off your computer.
Step 2: Remove the cover from the computer.
Step 3: Select an unused PCI/PCI Express slot.
Step 4: Carefully insert your I/O card into the PCI/PCI Express slot.
Step 5: Replace the PC cover.
Step 6: Power on the computer.
After powering-on the computer, please finish the Plug&Play steps according
to the prompted messages.
R=10K O.C.
Out => BSP75N External
Device
External
Power
(+)
(-) GND
R1
I1
Low Drive
Channel
DC
10V~30V
+
-
Open Collector Output Type & Notice
High Drive channel : Open collector N-channel Power FET (BPS75N) . Max. Sink
Current Is 500mA for Each Cannel .
Low Drive channel : Open collector NPN/PNO Transistor . Max. Sink Current Is
100mA for Each Channel .
(Recommend : It Is necessary to connect a diode In the External Device end as means
of preventing damage form the counter emf . If your External Device Is
inductive Load , Ex. Relay …)
R=3.9K External
Device
External
Power
(+)
(-) GND
R1
I1
D1
High Drive
Channel
DC
10V~30V
+
-
R=10K
O.C.
Out => 2N2222
Sink current
500mA
Sink current
100mA
Diode
External Power (+)
External Power (+)
External Power (-)
External Power (-)
DOn
DOn
-
Diode
PISO-P32S32WU
PISO- C64
P32C32
P32S32WU
External
Device
External
Power
(+)
(-) GND
R1
PISO-P32A32 / PISO-A64
DC
10V~30V
+
-
R=6.8K
O.C.
Out
D
R=10K
I1
External Power (+)
DOn
Source current
100mA
External Power (-)
Low Drive
Channel
If your control device is an inductive load (ex: inductive relay), it is recommended
to connect a diode at the Control Device side as a means of preventing damage
from the counter EMF.
Wiring Note
Installing Hardware on PC
To prevent the board damaged forever by overload, the GND pins (CON1: pin 1/20,
CON2: pin 1/20) all must be connected with GND of External Power.

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.
4
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Pin Assignments
Extension Cable (CA-4037B):
DB-40-Pin conversion DB-37-Pin

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.
5
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Prepare for device:
DN-37 (optional) wiring terminal board.
Exterior power supply device. For example: DP-665 (optional)
Self-test wiring as follows:
1. Use the DN-37 to connect the CON1 on board.
2. Keep set the J1 and JP2 jumper to External Power (Page 2).
3. Connect the DI(0-15) with DO(0-15). (DI0 with DO0 …DI15 with DO15)
PEX-P32C32 and PISO-P32C32U External Power Wiring:
4. Power Supply (+24 V) connect to ECOM0 (Pin18).
Power Supply (+24 V) connect to Ext.PWR0 (Pin37).
Power Supply GND connect to IGND0 (Pin19).
Power Supply GND connect to Ext.GND0 (Pin1 and Pin20).
PISO-P32C32U-5V External Power Wiring:
4. Power Supply (+5 V) connect to ECOM0 (Pin18).
Power Supply (+5 V) connect to Ext.PWR0 (Pin37).
Power Supply GND connect to IGND0 (Pin19).
Power Supply GND connect to Ext.GND0 (Pin1 and Pin20).
Self-Test
The PEX-P32C32/PISO-P32C32U suggests input voltage range as follow:
Logic high: +9 ~ +24 V; Logic Low: 0 ~ 1V.
(Higher voltage over the limitation will cause the hardware damage.)
The PISO-P32C32U-5V suggests input voltage range as follow:
Logic high: +5 ~ +12 V; Logic Low: 0 ~ 1V.
(Higher voltage over the limitation will cause the hardware damage.)

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.
6
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
The PEX-P32C32/PISO-P32C32U wiring is illustrated in the figure below:
The PISO-P32C32U-5V wiring is illustrated in the figure below:

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.
7
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
5. Execute the UniDAQ Utility Program.
This program (UniDAQ Utility) will be
placed in the default path after
completing installation.
The UniDAQ Utility.exe is located in:
C:\ICPDAS\UniDAQ\Driver\
(Default path).
6. Get DIO function test result.
Confirm the PISO-P32C32U
series card had successfully
installed to PC. It starts from 0.
2
Double-Click
1
Click this button
to start test.
3
Select the “Port 0”.
Check channel 0, 2, 4, 6
6
5
Click “Digital Output” item.
4
Port0: DO0-7
Port1: DO8-15
Port2: N.C.
Port3: N.C.

PEX-P32C32/PISO-P32C32U Series Quick Start Guide ICP DAS CO., LTD.
8
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Note!! All the DI should become red because all the DO is OFF (uncheck).
PEX-P32C32 and PISO-P32C32U Series Card Product Page:
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/piso-p32c32u.html
DN-37, CA-3710 and DP-665 page (optional):
http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
http://www.icpdas.com/products/Accessories/power_supply/dp-665.htm
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
Documentation and Software:
CD:\NAPDOS\PCI\UniDAQ\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
Select the “Port 0”
8
The corresponding D/I becomes black
for channel 0, 2, 4, 6 of D/O is ON.
9
Click “Digital Input”item.
7
Related Information
Port0: DI0-7
Port1: DI8-15
Port2: N.C.
Port3: N.C.
PASS