ICS LANTAP User manual
LANTAP
Primus Epic LAN Interface Kit
For these instructions and other information See:
http://www.icsaero.com/products/groundtest/lantap-10
Installation Instruction
REV H June 11th, 2018
Innovative Control Systems, Inc.
10801 N. 24th Ave. Suite 103.
Phoenix, AZ 85029 U.S.A.
+01 602-861-6984 Voice
+01 602-794-6453 FAX
http://www.icsaero.com
Page 2
Cable Connection
On the BNC side of the LANTAP,
make sure that the COAX, T, and
Terminator are connected as shown:
The LANTAP Adapter is a very simple and easy to use so-
lution for connecting a standard 10/100/1000BaseT Ether-
net bus to the Primus EPIC LAN.
On the opposite end, plug one end of the USB cable into the port
marked USB on the LANTAP, and the other end into your computer.
Please note, that ICS strongly recommends using a USB 3.0 port. These
are usually blue instead of black or grey and provide up to 1 amp of
current.
Please make sure that your com-
puter is powered on and running.
Diagnostic LED,10/100/1000 Link.
Light Green / Flashing Green with
10/100/1000BaseT activity. RED
on collisions between 10/100/1000
and 10Base2
Diagnostic LEDs, 10Base2
Activity Yellow Flashing on
Activity
Page 3
Next plug your RJ-45 network cable (shown be-
low) into the LANTAP port marked 10baseT Ether-
net. Plug the other end of this network cable into
the network port of you computer.
Please make sure you
have the correct IP
address and subnet
mask setup on the
network interface you
connected the LANTAP
Adapter to. You may
need to contact your
system administrator, or
aircraft vendor.
Note: For Cessna aircraft,
Cessna Customer Service
recommends an IP address of
192.168.200.196
or
192.168.200.197
Troubleshooting Tips:
No lights:
If you see any messages on your laptop regarding a USB port:
Some laptops do not fully supply the specified 500ma continuous current rating. Please try
a different port or check with your laptop’s manufacturer to see if the USB ports are to
spec. In normal operation, you won’t see any popup message about the USB port or the
LANTAP kit.
Make sure the black USB cable is plugged in to your laptop and the black
box:
The LANTAP kit is USB powered and requires this cable be plugged in to function.
Is the Network cable plugged in to your laptop and the black box?
The yellow network cable is necessary for the LANTAP kit to communicate with your
laptop.
Make sure that your laptops network connection is enabled.
In Windows XP, open the Control Panel and then open Network Connections. Make sure
your laptop’s built in network port is enabled (Usually labeled Local Area Connection)
Connection Failed:
Have you set an IP address on your laptop's network interface?
Please make sure that you have set the correct IP address and subnet mask on your
laptop’s network port. If you don’t know what IP address to use, we suggest the following:
IP Address: 192.168.192.7 Subnet Mask: 255.255.0.0
Cessna Customer Service recommends the IP address be set to:
192.168.200.196 or 192.168.200.197
Do you have an older PCMCIA style network card installed in your laptop?
These will normally interfere with the operation of the new LANTAP kit and must be
completely disabled or removed.
Is the COAX cable plugged in properly?
The COAX cable should plug in to the aircraft on one end and the TEE connector with the
Terminator included with the kit on the other exactly as shown on page 2 of this booklet.
Instructions for setting your IP Address:
http://www.icsaero.com/products/groundtest/lantap-10/lt10-quickstart-xp
Please check for further info at: http://www.icsaero.com
For further support or for any questions, please contact us at:
[email protected] or Phone +01 602-861-6984
Phone support is available Monday through Friday 8:00 A.M. to 4:00 P.M
Table of contents
Other ICS Adapter manuals
