ICWUSA ELITE 5120 User manual

ELITE 5120 InsTaLLaTIon
ELITE 5120 INSTALLATION - rev 12/22/15 pjm
If you have any questions please call Toll Free 1-800-558-4435
ICWUSA.com, Inc.
Page 1 of 3
Instructions for All Congurations
DO NOT use power tools to assemble or
adjust the arm. Use hand tools ONLY.
IMPoRTanT
ICW recommends wood or metal stud mounting only.
MAXIMUM LOAD CAPACITY:
28 LBS (12.7 KG)
•Do not attempt to adjust the Elite arm until all
components are mounted (monitor, keyboard, etc.)
•Arm must be completely horizontal (extended)
before adjusting the arm’s tension. Failure to do so will
damage the arm and void the warranty.
•NEVER loosen or remove any of the shoulder
bolts. Doing so will cause the arm to immediately
come apart with tremendous force, and could cause
serious injury.
• If equipment requiring AC power is mounted to this unit,
have a certied electrician inspect the installation.
• Failure to install this unit according to these instructions
will void all ICW warranties. If installed incorrectly, ICW
is not liable for any damage or injury caused by the unit.
The Elite arm contains high pressure gas
springs. The following cautions MUST be
observed to avoid serious injury.
DanGER!
Follow instructions on the following pages for style
of mount.
Ceiling Mount.............................................. Page 2
Quicklink..................................................... Page 2
Pole Mount ................................................. Page 3
Wall & Wall Track Mount............................. Page 3
Paralink....................................................... Page 4
aTTaCH aRM To MoUnT
REMoVE aRM CoVERs
TOP COVERS:
Remove the long arm covers by unscrewing the
two 1/4” long 6-32 athead screws
in the center of the cover
using a Phillips head
screwdriver.
END COVERS:
Remove the end covers
by unscrewing the two 3/4” long
10-24 athead screws using a
Phillips head screwdriver.
MOUNT
aDJUsT aRM REsIsTanCE
MOUNT
Extend the arm
straight out as shown
before adjusting the arm’s
resistance. Be sure all equipment
is mounted on the arm before
adjusting. Use the T-handle provided
to adjust the arm’s resistance.
DO NOT USE POWER TOOLS TO ADJUST.
ManaGE WIREs THRoUGH aRM
MOUNT
Run wires through end frame
and along channel.
Before reattaching arm
covers, slip wires through
end cover ports.
Reattach black plastic
bushing around exiting
wires.

ELITE 5120 INSTALLATION - rev 12/22/15 pjm
ELITE 5120 InsTaLLaTIon
Page 2 of 3
If Mounting to a Ceiling If Using a Quicklink
MoUnT InLInE CEILInG PLaTE
Firmly secure ceiling plate
to solid ceiling joist using
four #14 wood screws found in
hardware bag, being sure mount
is level. Be sure to loosen set screw
BEFORE attaching pipe.
Loosen set screw
in ceiling plate
before attaching
ceiling pipe.
MoUnT sQUaRE CEILInG PLaTE
Loosen the set screw
in ceiling plate before
attaching ceiling pipe.
Using four 1/4 x 2” lag bolts
provided in hardware bag,
secure ceiling plate to a solid
wood surface or ceiling joist.
Use square pattern or inline
pattern, always being sure to
use all 4 bolts.
Run wires through center
hole or wire management
port. Be sure to loosen set
screw BEFORE attaching
ceiling pipe.
Wire management holes
aTTaCH PIPE To CEILInG PLaTE - InLInE & sQUaRE
Screw extension
pipe rmly into
ceiling plate, then
tighten set screw.
Tighten set
screw after
pipe is tightly
screwed in.
aTTaCH PIPE To aRM
Screw Elite arm
rmly onto extension
pipe, then tighten
set screw.
Tighten set screw
after Elite arm
is completely
screwed in.
aTTaCH VEsa anD HanDLE To MonIToR
Using a Phillips
screw driver, attach
the VESA plate to
the back of the LCD
monitor using four
4mm screws in the
hardware bag.
Attach handle to
VESA plate.
aTTaCH PaRaLInK To aRM
9/16 wrench
Nut
Remove nut from bolt on
Quicklink. Attach Quicklink
to arm. Thread nut onto
bolt through front of arm
assembly. Tighten bolt
with provided 9/16 wrench.
aDJUsT QUICKLInK TILT
Quicklink
buttons
Pivots
Use the under-monitor handle
to rotate, tilt and swivel the
monitor to desired position.
Increase range of motion by
depressing buttons on back
of Quicklink. Each button
provides 90° of adjustment
for its corresponding pivot.
Depressing both buttons
at once provides 180° of
adjustment.

ELITE 5120 InsTaLLaTIon
ELITE 5120 INSTALLATION - rev 12/22/15 pjm
If Mounting to a Wall or Wall Track
MoUnT To WaLL TRaCK
Attach wall track to wall using installation
instructions provided with track.
Attach track adapters to back of wall ear by threading
socket head screws from front of wall ear into track
adapters. Loosely tighten with 5/32” hex key.
Attach wall plate to track by sliding track adapters
into track from either top or bottom. Position wall ear to
desired location on track. Firmly tighten wall ear screws
with 5/32 hex key.
REMoVE aRM FRoM WaLL EaR REaTTaCH aRM To WaLL EaR
If Mounting to a Pole
Remove beauty cap. Using 5 mm
hex key from above and T-handle
from below, loosen bolt. Separate
arm and wall ear.
Align arm with wall ear and slide
parts together. Using 5 mm hex
key from above and T-handle
from below, tighten bolt. Replace
beauty cap.
aTTaCH WaLL PLaTE To WaLL EaR
Attach wall plate to wall ear using
provided 5 mm hex key and four
1/4-20 screws.
5 mm hex key
5mm hex key
Beauty cap
Beauty cap
T-handle T-handle
aTTaCH aRM To WaLL
• Locate stud and mark top hole.
• Drill 11/64 pilot hole and insert #14 screw and
tighten slightly.
• Using a level, mark lower holes and drill pilot holes.
• Insert #14 screws and, with unit level,
tighten all screws.
ICW supplies #14 wood screws. If installing
onto metal studs, you will need to replace
with proper metal stud fasteners.
To tighten center screw, additional
tools may be helpful (not provided).
Provided screws will accept a
90° bent Phillips or square bit
nut driver on a short
socket wrench.
aDJUsT RoTaTIon LIMITs - WaLL MoUnT
The rotation limits for the arm are set
by placing the stop pins in the holes
corresponding to where you want the arm
to stop. The stop pin then bumps into the
stop block on the front of the wall mount
ear, stopping the arm. The stop pins can
be removed and set by hand.
Stop Pin
Stop block
aTTaCH To PoLE
Detach pole mount from
arm using the provided 5/32 hex key.
Separate the two sections of the pole
mount. Place around the pole and
rmly reassemble.

If you have any questions please call Toll Free 1-800-558-4435
ELITE 5120 InsTaLLaTIon
ELITE 5120 INSTALLATION - rev 12/22/15 pjm
Page 4
aTTaCH PaRaLInK KEYBoaRD To MonIToR
Attach the Paralink
keyboard mount to
the monitor mount
by using the 3/8-
16 screw and lock
washer provided.
aTTaCH PaRaLInK KEYBoaRD TRaY
• Remove beauty cap on
Paralink.
• Remove screw using 3/16”
hex key.
• Slide keyboard tray into
Paralink.
• Replace screw and tighten.
• Replace beauty cap.
• Loosen knob, adjust Paralink
to desired position, then
tighten knob.
Beauty cap
Screw
Adjustment
Knob
Attach VESA
to monitor
using four
4mm screws
in the
hardware
bag.
aTTaCH VEsa To MonIToR MonIToR TILT, RoTaTIon & aDJUsT MonIToR DEPTH
MONITOR TILT
& ROTATE
Gently hold sides
of monitor. Tilt and
rotate to desired
position with ball
VESA.
ADJUST
MONITOR
DEPTH
Loosen the
adjustment
knob, move
the Paralink
forward or
back, then
re-tighten
the knob.
Adjustment
Knob
If Using Ultra Keyboard
If Using Paralink
Attach the tray
ip-up assembly
to the drop plate
using the provided
at head screws
and hex key.
aTTaCH FLIP UP TRaY To ULTRa DRoP
aDJUsT BaLL VEsa TEnsIon & HEIGHT
Pivot tension
adjustment screws
Use the slider knob
to loosen the slider
to adjust the height
of the monitor on the
Paralink.
Adjust the pivot tension
of the ball by gently
and evenly tightening
or loosening the four
screws on the back of
the ball VESA.
Slider knob