Ideal Air 700485 User manual

MODEL: 700485
700490
700495
MINI-SPLIT 13 SEER AIR CONDITIONER
INSTALLATION VIDEO AVAILABLE ON www.ideal-air.com

When Connecting Refrigerant Tubing
Tighten the nut with a torque wrench for a leak free connection.
Open the stop valves all the way and leave open. Check for leaks
with soapy water at all refrigerant line connections.
NOTE:
Depending on the system t
vide snow vents.

Serrer l'écrou avec une clé dynamométrique pour une
connexion sans fuite.
Ouvrir les vannes d'arrêt tout le chemin et laisser ouverte.
Vérifiez pour les les fuites avec la l 'eau savonneuse
à tous les connexions de ligne de de fluide frigorigène.

T o o l n am e C o n t e n t s o f c h a n g e
C h a rg e h o s e T o in cr ea s e p re ss u r e res is ta nc e, t he h o se m a te ria l a nd b a s e s iz e w ere c ha n ge d .
Va c u u m p u m p A co nve n tio n al v a cuu m pu m p c an be u se d b y in st allin g a va cu um p um p ad a p te r.
G a s le a k ag e d e te c t o r Sp e cia l ga s lea k a g e d et ec to r fo r H F C re frige r a nt R 4 1 0A .
G a u g e m a n if o ld
Pr e s s u re is h ig h an d c an n o t b e m e a su re d w it h a c o n v en t io n a l ga u g e. T o p re v e nt
err o ne o u s m ixin g o f ot he r re fr ig er a n ts, th e d ia m et er of e a ch p o rt h a s b e en c ha n g ed .I t
is r e co m m en d e d th e g au g e w ith s ea ls - 0 .1 t o 5. 3 M P a (-1 t o 5 3 ba r ) f or hig h
pre s s u re .-0. 1 to 3 . 8 M Pa (- 1 t o 38 ba r ) fo r lo w p re s s u r e.
Nominal diam eter Outer diameter Thickn ess
1/4in 6.35mm 0.8mm
3/8in 9.52mm 0.8mm
1/2in 12.7mm 0.8mm
5/8in 15.88m m 1.0mm
thickness of annealed copper pip e

Table 4
Cooling/Dry Mode Heating Mode
Outdoor temperature 0C(32F)~46C(115F) -23C(-10F)~23C(75F)
Indoor temperature 16C(60F)~30C(90F) 10C(50F)~30C(90F)
Indoor humidity 80% -
Table 5
Pipe length 25 ft (7.5 m) 33 ft (10 m) 49 ft (15 m) 66 ft (20 m) 83 ft (25 m)
Additionalrefrig
erant None 1.8 oz (50 g) 5.3 oz (150 g) 3.5 oz (100 g) 9.0 oz (200 g)
12KBTU 24KBTU 36KBTU
MINIMUM CIRCUIT AMPACITY 15A 21A 22A
MAXIMUM OVERCURRENT
PROTECTION(TIME DELAY FUSE OR
HACR TYPE CIRCUIT BREAKER)
20A 25A 30A
e system before beginning.
Installation Accessories Name Q’ty Use
Wall hook bracket 1 For indoor unit
installation
Rem ote controller 1 Use for air conditioner
operation
Battery 2 For remote control unit
Drain Pipe 1 For indoor unit
installation
Wall Caps 1 For indoor unit
installation
Wall Pipe 1 For indoor unit
installation
Thermostat Pigtail 1 For Therm ostat
connection
Outdoor unit bracket 1 For outdoor unit
installation

120V,60HZ

Important:
Before pushing down handle, verify fittings
are properly aligned. If improperly aligned,
damage to O’rings will occur allowing refrigerant
leakage.

Remove the waterproofing covers on the outdoor unit quick connectors.
Inspect both quick connectors on outdoor unit and lineset for debri,
clean if necessary.
If debri is allowed to enter system, damage may occur.
Connect the quick connect fittings to the outdoor unit valves with 2 wrenches.
DO NOT OVER TIGHTEN, DAMAGE & LEAKAGE WILL OCCUR.
Remove the brass caps on the two valves with a wrench.
Open the liquid valve & gas valve with an allen wrench.
Reinstall the brass caps on the valves.
Gas leakage Inspection:
After connecting the piping, check all connections & caps for leakage
carefully, soapy water or an electronic refrigerant detector can be used.

1. Start the A/C, operate in Cooling mode.
2. Remove the cap of the two valves with a wrench.
5. Disconnect the power cable from outdoor unit.
6. Loose the nut of the quick connect pipe from the outdoor unit valve with 2 wrenches
INSURE NO DEBRI ENTERS THE QUICK CONNECTS.
IF DEBRI IS ALLOWED TO ENTER SYSTEM, DAMAGE MAY OCCUR.

115
115
AC-N
W G
R Y
B/O
BLUE

CN5
CON12
CON11
CN6
CN4
C0N9
2
CN10

CN6-UP
CN7-R
CN8-L
CN10
CN3
CNA
CN2
OUTPUT
CN12
W
G
RY
B/O

(3 ) A lw a y s f a s te n th e o u tsid e co v e r ing o f th e
co nn e ct io n co rd w ith t h e co rd c lam p. ( If th e
ins ula to r is ch af e d, ele c t ric le aka g e m a y o c c ur. )
(4 ) S e cu r ely ea r th t h e po w e r c o r d p l ug .
(2 ) C o n n ec t t he c o nn e c tio n co r d s f irm ly to t he
te rm in a l b lo c k . Im p e rf e c t ins ta ll a tio n m a y ca us e a
fi r e.
(5 ) D o no t u s e th e e a rt h sc r e w f o r an ext e rn a l
co nn e ct or .O n ly u s e f or in t er c o n n ec tio n
be t w ee n t w o un its .
(1 ) M a tc h th e te r m in al blo c k n um b e r s a n d
co nn e ctio n co r d c o lo rs w ith t ho s e of th e o u td o or
un i t. Er r o ne o u s w ir in g m ay ca u se b ur n i n g of t he
ele c tr ic p ar ts .
120v/60hz power
12kbtu
230v/60hz power
24kbtu 36kbtu

Be sure to comply with local codes while running the wire from the
indoor unit to the outdoor unit (size of wire and wiring method, etc. ).
Every wire must be connected firmly.
No wire should be allowed to touch refrigerant tubing, the
compressor or any moving part.
Loose wiring may cause the terminal to overheat or result in unit
malfunction. A fire hazard may also exist. Therefore, be sure all
wiring is tightly connected.
Connect wires to the matching numbers & colors of terminals.
120V/60HZ
12KBTU
230V/60HZ
24KBTU/36KBTU
(1) The rated voltage of this product is 120v/60hz for
12kbtu unit, 230v/60hz for 24kbtu & 36kbtu unit.