Ideal Boilers Concord CXSD 100/H User manual

2Concord CXAP 40/H-100/H - User's Guide
ALL MODELS
THE GAS SAFETY (INSTALLATION & USE)
REGULATIONS OR RULES IN FORCE impose
certain statutory obligations on gas users. This
appliance must be installed by a CORGI
registered installer.
WARNING.
This appliance MUST be efficiently earthed.
1. It is ESSENTIAL that the instructions in this booklet
are strictly followed, for safe, economical operation
of the boiler.
2. Do not obstruct ventilation ducts, grilles or openings
in the boiler room, or the passage of combustion
and ventilation air to the boiler.
3. Do not store objects around or on the boiler, and
keep access clear at all times.
4. Switch off and disconnect the electricity supply
before carrying out maintenance work.
5. Do not turn off the boiler if it is to be left unattended
in frosty weather.
MAINTENANCE
The appliance should be serviced at least once a year
by a CORGI registered installer.
CLEANING
For normal cleaning simply dust with a dry cloth.
To remove stubborn marks and stains use a damp cloth
and mild detergent.
DO NOT use abrasive cleaning materials.
CAUTION. To avoid the possibility of injury during the use or cleaning of this appliance care
should be taken when handling edges of sheet steel components.
CONCORD CXAP 40/H - 80/H models
LEGEND
1. Thermostat knob.
2. Mains gas inlet cock.
3. Overheat thermostat
button.
4. Lockout light.
5. Lockout reset button.
6. Burner on light.
7. Overheat light
CHANGING CYLINDERS
a. Ensure that the replacement cylinder is the correct one for the
installation.
b. Extinguish any fire, flame our source of ignition (including
cigarettes, pipes and pilot lights) before changing the gas
cylinder.
c. Change cylinders with caution.
d. Ensure that the gas cylinder valve(s) is/are closed before
disconnecting an empty cylinder or before removing any
plastic cap or plug on the outlet connection of the replacement
cylinder.
Never use tools on cylinder valves, hand wheels or levers.
Note. Cylinders with threaded connections have a LH thread.
For cylinders with self-sealing clip-on valves, ensure that the
regulator cap is closed before disconnection.
e. Ensure that the replacement cylinder connections are
gastight. Any leaking vapour will have a distinctive odour. Test
for leaks, using leak detection fluid.
NEVER USE A NAKED FLAME
f. It is essential that the correct pressure regulator, with the
correct pressure setting and capacity for the installation, be
used in accordance with the manufacturers instructions.
g. In the case of a pressure regulator or a gas appliance which
relies upon a sealing washer to maintain a gastight joint, it is
essential to check that the washer is present and that it is
sound and correctly positioned prior to making the connection.
h. Where connections are designed to be tightened with a
spanner, it is essential that a spanner of the correct size is
used and that the union is firm - hand tightness is not
sufficient.
When self sealing valves are incorporated in a gas cylinder,
connections should be made in accordance with the
manufacturer's instructions and tools should not be used.
65
74
1
2
2
3
Con 5241

3
Concord CXAP 40/H-100/H - User's Guide
CONCORD CXAP 90/H - 100/H models
ALL MODELS
TO LIGHT THE BOILER
1. Check that the boiler thermostat knob (1) on the control box
is OFF.
2. Ensure that the mains gas inlet cock (2) is open (groove in
the square head in line with the gas pipe).
3. Press in the overheat thermostat button (3).
4. Switch on the electrical supply to the boiler.
5. Ensure all system controls (time switch, system controls
etc.) are calling for heat.
6. Turn the boiler thermostat knob (1) to position 6.
7. If the boiler does not light at the end of the ignition period
the Lockout light (4) on the control box will be illuminated.
Press in and release the Lockout reset button (5). The
controls will reset and after a period of time will attempt to
relight.
8. Once the pilot has lit the controls open the main gas valves,
the main burners will light and the Burner On light (6) will
be illuminated.
9. Set all system controls to the required settings.
10. Set the boiler thermostat knob (1) to the required setting.
CONTROL PANEL LIGHTS
1. The Boiler On light (6) is illuminated while the boiler is firing.
2. If the Overheat light (7) is lit, pull off the casing lower front
panel and press in the overheat reset button (3). Replace the
lower front panel and follow the boiler lighting instructions
above. If the overheat condition persists consult a CORGI
registered installer.
3. If the Lockout light (4) is lit press in the Lockout reset button
(5).If the lockout condition persists consult a CORGI registered
installer.
LEGEND
1. Thermostat knob.
2. Mains gas inlet cock.
3. Overheat thermostat
button.
4. Lockout light.
5. Lockout reset button.
6. Burner on light.
7. Overheat light
2
TO SHUT DOWN THE BOILER
For short periods
Turn the boiler off at the time clock or system controls. Wait for
6 minutes and then turn the boiler control thermostat knob (1)
to OFF. Note the frost warning below.
For long periods
Turn the boiler off at the time clock or system controls. Wait for
6 minutes and then turn the boiler control thermostat knob (1)
to OFF. Turn off the inlet gas cock (groove in the square head
across the line of the gas pipe). Note the frost warning below.
TO RELIGHT THE BOILER
After short periods
Switch on the time switch or system controls and turn boiler
thermostat knob (1) to the required setting. The boiler will light
providing the external controls are calling for heat.
After long periods
Refill the system if it has been drained. Follow the lighting
instructions above.
FROST WARNING
If frost is likely, leave the boiler thermostat at position 6 and do
not turn off the gas cock. This will enable the built-in frost
thermostat to protect the boiler. Note that this may not protect
remote parts of the system, in which case a separate frost
thermostat should be fitted or the system drained and the
boiler shut down for as for "Long Periods".
Knob setting Approx flow Approx flow
temp οο
οο
οC temp οο
οο
οF
1 60 140
2 64 147
3 69 156
4 73 163
5 77 171
6 82 180
3
Con 1971
2
1
65
47

Ideal Boilers , P.O. Box 103, National Ave, Kingston upon Hull,
HU5 4JN. Telephone: [phone] Fax: [phone].
Registration No. London 322 137.
January 2002 UIN 157299 A02
Caradon Ideal Limited pursues a policy of continuing
improvement in the design and performance of its products. The
right is therefore reserved to vary specification without notice.
I deal Installer/Technical Helpline: 01482 498 376
www.idealboilers.com
EMERGENCY ACTION
GAS LEAK
(usually detected by a distinctive smell)
Do NOT use electrical switches
DO NOT look for a leak with a naked flame
IMMEDIATE ACTION:
• CLOSE all supply valves.
• EXTINGUISH all sources of ignition.
• Open all doors and windows.
• If leakage cannot be stopped REMOVE CYLINDERS to a
safe place in the open air and advise the supplier. If this is
not possible, evacuate the premises and call the fire
brigade.
• Do not use the installation until it has been checked by a
CORGI registered installer.
EMERGENCY ACTION
FIRE
IMMEDIATE ACTION:
IF SAFE TO DO SO, SHUT OF GAS SUPPLY
Do not attempt to extinguish the flames by any other means.
Raise the alarm and call the fire brigade stating that a
liquified petroleum gas cylinder is involved, and give its
location.
DO NOT GO NEAR THE CYLINDER if a cylinder is being
heated by fire.
ALERT EVERYONE in the immediate area of the fire and
evacuate the building.
ADVISE THE FIRE BRIGADE on their ARRIVAL of the
LOCATION of the cylinder.
If a cylinder is not involved in the fire and it is SAFE TO DO SO,
close all cylinder valves and remove the cylinder to a safe place.