Ideal Boilers Harrier GTS User manual

users guide
Your Ideal users guide
ENGINEERED FOR PEACE OF MIND
When replacing any part on this appliance, use only spare parts that you can be
assured conform to the safety and performance specification that we require. Do not
use reconditioned or copy parts that have not been clearly authorised by Ideal Boilers.
Harrier GTS
Viceroy GTS
Viscount GTS
All Models
300014486-001-A

2Harrier GTS, Viceroy GTS, Viscount GTS - User's
Harrier GTS
(Gas and Fuel Oil)
PI No. 1312BR4783
INTRODUCTION
TheHarrier GTS, Viceroy GTS and Viscount GTS arefloor-
standing boilers featuring full sequence automatic gas or fuel
oil burners.
SAFETY
It is essential that the instructions in this booklet are
strictly followed, for safe and economical operation of the
boiler.
FOR GAS FIRED BOILERS
Current Gas Safety (Installation & Use)
Regulations or rules in force.
In your own interest, and that of safety, it is the law that this
boiler must be installed and maintained by a CORGI
registered installer, in accordance with the above regulations.
The appliance should be serviced at least once a year by a
CORGI registered installer.
Electricity Supply
The appliance must be earthed.
Supply 230 V - 50 Hz.
The appliance is intended to be connected to the supply via a
double-pole switch, having a 3mm contact separation in both
poles, serving only the boiler and system controls.
Alternatively, a 3-pin UNSWITCHED socket may be used.
The burner and circulating pumps may be 1ph or 3ph.
Important Notes
• Do not store objects around or on the boiler, and keep
access clear at all times.
• Do not obstruct ventilation ducts, grilles or openings in the
boiler room or the passage of combustion and ventilation
air to the boiler.
• Do not turn off the boiler if it is to be left unattended in frosty
weather.
• If it is known or suspected that a fault exists on the boiler then
it MUST NOT BE USED until the fault has been corrected by a
recognised installer (CORGI registered for gas-fired boilers).
• Flammable materials must not be placed in close proximity to
the appliance. Materials giving off flammable vapours must
not be stored in the same room as the appliance.
In cases of repeated or continuous shutdown, a recognised
installer (CORGI registered for gas-fired boilers) should be called
to investigate and rectify the condition causing this and carry out
an operational test after each intervention on the device. Only the
manufacturer's original parts should be used for replacement.
Minimum Clearances
Harrier GTS:
Clearances of 1000mm (40") at the rear, 200mm (8") plus burner
projection on burner hinge side or 500mm (20") whichever is the
greater on one side and 100mm (4") on the other side and
1500mm (60") at the front of the boiler casing must be allowed
for servicing.
ViceroyGTS:
Clearances of 1000mm (40") at the rear, 200mm (8") plus burner
projection on burner hinge side or 500mm (20") whichever is the
greater on one side and 100mm (4") on the other side and
1500mm (60"), GTS 8; 2000mm (78"), GTS 9, GTS 10 and
GTS 11; 2500mm (98") GTS 12, GTS 13 and GTS 14 at the
front of the boiler casing must be allowed for servicing.
ViscountGTS:
Clearances of 300mm (12"), GTS14; 436mm (17"), GTS15 and
GTS16; 656mm (26"), GTS17, 18 and 19; 936mm (37"), GTS20,
21 and 22; 1266mm (50"), GTS23, 24 and 25 at the rear,
1200mm (48") on the burner door hinge side plus allowance
depending on burner projections and 500mm (20") on the other
side and 1500mm (60") plus allowance depending on burner
projection at the front of the boiler casing must be allowed for
servicing.
Destination Countries: GB,IE
Viceroy GTS
(Gas and Fuel Oil)
PI No. 1312AQ 952
Destination Countries: GB, IE
vic9104
vis9128
Viscount GTS
(Gas and Fuel Oil or Dual Fuel Fired)
PI No. 1312AQ 954
Destination Countries: GB,IE
CAUTION. To avoid the possibility of injury during the installation, servicing or cleaning
of this appliance care should be taken when handling edges of sheet steel components
AllCORGI RegisteredInstallers carrya CORGIID card,and havea registrationnumber. Both shouldbe recorded
in your Log Book. You can check your installer by calling CORGI direct on 01256 372300.

3
Harrier GTS, Viceroy GTS, Viscount GTS - User's
1 BOILER CONTROLS
2 CONTROL OF WATER TEMPERATURE
The water temperature is controlled by the boiler thermostat (item 3A). The temperature range of the thermostat is 30 - 90oC for
ON/OFF operation. For boilers fitted with high/low burners, a 2nd stage thermostat controls the burner changeover from high to
low fire at a recommended setting 5oC lower than the maximum flow temperature setting.
Note.
The setting numbers 3-9 are approximately scaled to represent 30-90oC.
To Light the Boiler (Refer to Frame 1)
1. CHECK THATTHE ELECTRICITY SUPPLYTOTHE BOILER
ISOFF.
2. Set the boiler on/off switch (1) to OFF.
3. Set the boiler flow temperature control (3A) to maximum (1st
stage control if high/low burner fitted).
4. Switch on the electricity supply to the boiler and check that all
external controls, e.g. programmer, room thermostat etc., are
on.
5. Set the boiler on/off switch (1) to ON.
The boiler will commence the ignition sequence, supplying
heat to the system when required.
Note. If the burner does not ignite refer to the burner
instructions.
6. Set the boiler flow temperature control (3A) to the desired
setting. If a high/low burner is fitted, set the 2nd stage
temperature control (3B) to a setting 5oC lower.
Settings below 4 (approx. 40oC) are not recommended, in
order to avoid the risk of combustion products condensing
on the walls of the boiler.
7. Burner
Refer to the instructions supplied with the burner for specific
control features.
7621 3A 3B 45
har9096
1. Boiler ON/OFF switch.
Position .....ON Position .....OFF
2. TESTSTB:
When held in the pressed (momentary use) position it
tests the safety thermostat.
Note. If two stage burner control fitted operation will
continue on 1st stage after 2nd stage cut-off.
3. Boiler Thermostats:
Adjustment range 30-90oC
For ON/OFF burners use 1st stage thermostat only.
For two stage burners set 2nd stage 5oC below 1st
stage setting.
4. Boiler Thermometer
5. Location for Flue Gas Thermometer (Optional)
6. Timed Circuit Breaker:
10A with delayed action and manual reset.
7. Safety Thermostat:
Set at 110oC. Manual reset.

To Shut Down the Boiler
1. For short periods
Set the boiler on/off switch (1) to OFF.
2. For longer periods
Set the boiler on/off switch (1) to OFF. Switch the electricity
supply to OFF. For longer periods the entire system should
be drained.
To Relight the Boiler
Refill the system if it has been drained, taking care to ensure
no air is in the boiler or system.
Repeat the procedure detailed in 'To light the boiler'.
Frost Protection
If frost is likely and dependant on the system controls, which
may incorporate suitable safety features, leave the boiler
thermostat at a reduced temperature setting. Ensure external
controls allow the boiler to operate if necessary. Note that this
may not protect remote parts of the system, in which case a
separate frost thermostat should be fitted or the system
drained and the boiler shut down, as for Long Periods.
Boiler Overheat Thermostat
Boiler overheating is detected by the overheat thermostat
connected to the boiler control module. If the boiler has
overheated, allow it to cool then, press the safety thermostat
reset button, under the screw top cap (7), and the burner will
relight. If the fault recurs, turn off the boiler and consult a
recognised installer (CORGI registered for gas-fired boilers.)
Escape of Gas
Should a gas leak or fault be suspected contact your local gas
supplier without delay.
Do NOT search for gas leaks with a naked flame.
Cleaning
For normal cleaning simply dust with a dry cloth.
To remove stubborn marks and stains use a damp cloth and
mild detergent.
DO NOT use abrasive cleaning materials.
Ideal Boilers , P.O. Box 103,NationalAve, Kingstonupon Hull, HU5
4JN. Telephone: [phone] Fax: [phone]. Registration
No. London 322 137.
November 2007 UIN 203622 A01
Ideal Stelrad Group pursues a policy of continuing improvement
in the design and performance of its products. The right is
therefore reserved to vary specification without notice.
I deal Commercial/Technical Helpline: 01482 498 376
www.idealboilers.com