ideal-tek PCSA Series User manual
PCSACircuit board holder
VARIABLE
COMBINATIONS (COMBINATIONS AND DIMENSIONS SEE NEXT PAGE)
PCSA-1 PCSA-4
PCSA-2
CIRCUIT BOARD HOLDER,
STANDARD, WITH 2
ADJUSTABLE
SUBDIVISIONS
PCSA-1
BS-PCSS1
utilizable size: 280 x 290
INSERTET SPLINTS
adjustable middle splint
2
2
4
-
-
1
1
-
CIRCUIT BOARD HOLDER STANDARD, WITH TWO
ADJUSTABLE SUBDIVISIONS
PCSA-2
BS-PCSS2-4
INSERTET SPLINTS
adjustable middle splint
2
2
4
-
-
1
1
-
PCSA-4
BS-PCSS2-4
INSERTET SPLINTS
adjustable middle splint
2
2
4
6
-
1
1
1
utilizable size 520 X 280 utilizable size 520 X 410
with cover,
foam rubber
ESD safe
with cover,
foam rubber
ESD safe
.
with cover,
foam rubber
ESD safe
Additional
splint,
adjustable
Additional splint,
adjustable
Additional splint,
adjustable
CIRCUIT BOARD HOLDER STANDARD , WITH TWO
ADJUSTABLE SUBDIVISIONS
PO Box 221, CH-6830 Chiasso 3 Tel. +4191/6383229 Fax +4191/6830371 [email protected] www.ideal-tek.com
ideal-tek s.a.
Subject to changes. The manufacturer declines any responsability for potential damages to persons or objects due to inappropriate usage.
SPLINT
- Circuit board holders of the PCSA series are the ideal tool for fitting circuit boards with components. The holder can easily
be demounted in single parts and be reassembled in different combinations.
-The standard models PCSA-1/2/4 are equipped with 1 fix middle bridge and 2 adjustable splints. Therefore two work areas
can be created.
-Any circuit board holders can be fit out with additional subdivisors (4 for PCSA-1/2/4 and 6 for PCSA-4).
That way small circuit boards can be laboured on several levels.
CIRCUIT BOARD HOLDER
- COMBINATIONS AND WORK SURFACE IN MM
20
2
1
4
1
2021
4
1
20211 2021
4
1
61
FEATURE
PCSA-1 PCSA-2 PCSA-4
SPLINTSPLINTSPLINT
FIX BRIDGEFIX BRIDGEFIX BRIDGE
SPLINTSPLINTSPLINTSPLINT
FIX BRIDGEFIX BRIDGEFIX BRIDGEFIX BRIDGE
PO Box 221, CH-6830 Chiasso 3 Tel. +4191/6833229 Fax +4191/6830371 [email protected] www.ideal-tek.com
ideal-tek s.a.
SPLINTSPLINT
FIX BRIDGEFIX BRIDGEFIX BRIDGE
HOW TO USE PCSA DETACHABLE ASSEMBLY JIGS FOR PC BOARDS
USING PC BOARD ASSEMBLY JIG IN VERTICAL POSITION
P siti ning f the l wer c rners f the PC
Assembly Jig in the t thed guides l cated n the
frame.
P siti ning at 70° angle P siti ning at 80° angle P siti ning at 90° angle
PC board assembly jig screwed onto
work top, with component press lid
down.
Foam rubber lined lid for holding
components in place. May be raised
once front lock has been released.
Raising of whole PC board assembly
jig unit rotating on its hinge pin.
Self adjustment to frame at right
working angle, after unit raising.
Easy to detach PC assembly jig from
frame. Rail positions as for types below.
PC Assembly jig with component press lid closed
screwed or clamped to work top, in relation to the
height of the components.
Foam rubber lined lid for holding components in
place. May be raised by appltying pressure to front
buttons (Anti static conducting foam rubber for
PCSA types)
Easy to unslot and detach various parts. (Frame
PC holder unit component Press Lid)
PC board assembly jig can be raised by turning
special lateral knobs. Self adjustment to frame at
right wotrking angle, after unit raising. Practical use f PC Assembly Jig with PC B ard in place. Uns ldering f c mp nents carfried ut with PC Assembly Jig in vertical
p siti ns.
Sliding rails may be p siti ned by means f self-
l cking sleeves. A system f springs makes it
p ssible t insert and rem vee printed circuit
b ards with ut changing p siti n f sleeves.
CENTRAL RAIL can be pressed into place Moveable couplings, located on the rear side of
the assembly jigs for attaching the PC assembly
jig to the frame. These couplings keep the PC
assembly jig from detaching from the frame should
it be moved in that direction.
PO Box 221, CH-6830 Chiasso 3 Tel. +4191/6383229 Fax +4191/6830371 [email protected] www.ideal-tek.com
ideal-tek s.a.
This manual suits for next models
3
