IEI Technology MODAT-200 User manual

MODAT-200
Page 1
IEI Technology Corp.
User Manual
MODEL:
MODAT-200
HANDHELD COMPUTER,
Quick Registration, Inspection, On-line Sales
Rev. 1.00 – 28 December, 2010

MODAT-200
Page 2
Revision
Date Version
Changes
28 December, 2010 1.00 Initial release

MODAT-200
Page 3
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

MODAT-200
Page 4
WARNING:
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This device and its antenna(s) must not be co-located or operating in conjunction
with any other antenna or transmitter.
IMPORTANT NOTE:
For product available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

MODAT-200
Page 5
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 OVERVIEW.................................................................................................................. 2
1.2 FEATURE .................................................................................................................... 2
1.3APPLICATIONS ............................................................................................................ 3
1.4 EXTERNAL OVERVIEW................................................................................................ 3
1.4.1 Front Panel ........................................................................................................ 4
1.4.2 Left Panel........................................................................................................... 5
1.4.3 Top Panel ........................................................................................................... 5
1.4.4 Bottom Panel...................................................................................................... 6
1.4.5 Rear Panel ......................................................................................................... 6
1.5 SPECIFICATIONS ......................................................................................................... 7
1.6 DIMENSIONS............................................................................................................... 9
2 INSTALLATION ......................................................................................................... 10
2.1 UNPACK THE DEVICE.................................................................................................11
2.2 PACKING LIST........................................................................................................... 12
2.3 CHARGING THE SYSTEM........................................................................................... 13
2.3.1 Using Cradle (Optional).................................................................................. 14
2.4 POWER-ON/OFF PROCEDURE ................................................................................... 16
A SAFETY PRECAUTIONS......................................................................................... 17
A.1 SAFETY PRECAUTIONS ............................................................................................ 18
A.1.1 General Safety Precautions............................................................................. 18
A.1.2 Anti-static Precautions .................................................................................... 19
A.1.3 Product Disposal............................................................................................. 20
A.2 MAINTENANCE AND CLEANING PRECAUTIONS........................................................ 20
A.2.1 Maintenance and Cleaning.............................................................................. 20
A.2.2 Cleaning Tools................................................................................................. 21
C HAZARDOUS MATERIALS DISCLOSURE......................................................... 22
C.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS

MODAT-200
Page 6
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY....................................... 23

MODAT-200
Page 7
List of Figures
Figure 1-1: MODAT-200..................................................................................................................2
Figure 1-2: MODAT-200 Front Panel.............................................................................................4
Figure 1-3: MODAT-200 Left Panel................................................................................................5
Figure 1-4: MODAT-200 Top Panel................................................................................................5
Figure 1-5: MODAT-200 Bottom Panel..........................................................................................6
Figure 1-6: MODAT-200 Rear Panel..............................................................................................6
Figure 1-7: MODAT-200 Dimensions (units in mm).....................................................................9
Figure 2-1: MODAT-200 Mini-USB connector ............................................................................13
Figure 2-2: Power Adapter USB Connector...............................................................................14
Figure 2-3: Battery LED................................................................................................................14
Figure 2-4: Mini-USB Connector of the Cradle..........................................................................15
Figure 2-5: Power Adapter USB Connector...............................................................................15
Figure 2-6: Connect the MODAT-200 to the Charging Cradle..................................................15
Figure 2-7: Power Button.............................................................................................................16

MODAT-200
Page 8
List of Tables
Table 1-1: MODAT-200 System Specifications............................................................................8
Table 2-1: Packing List.................................................................................................................13

MODAT-200
Page 1
Chapter
1
1 Introduction

MODAT-200
Page 2
1.1 Overview
Figure 1-1: MODAT-200
The MODAT-200, built-in Windows Mobile 6.5, offers real-time information for staff to
provide their guests with better, faster service and more information.
The MODAT-200 links the staff to real-time, online data to serve customers with better,
faster service through Wi-Fi and connected Bluetooth devices such as headsets and
thermal printers. A built-in vibrator can alert the wait staff that an order is ready to be
served.
1.2 Feature
The MODAT-200 features the following:
667 MHz ARM11 CPU with built-in hardware codec (H.264/MPEG4/VC-1) and
2D/3D graphics acceleration
3.5” sunlight readable high brightness transflective TFT touchscreen with
stylus input
MicroSD Slot
USB client (for ActiveSync and battery charging)
Wi-Fi 802.11b/g

MODAT-200
Page 3
Bluetooth 2.0 + EDR
IP 54 compliant
Windows Mobile 6.5 preinstalled
Support Visual Studio .NET and .NET Compact Framework development
tools
Mobile application downloads: Windows Marketplace for Mobile
(http://www.windowsmarketplace.com)
1.3 Applications
The MODAT-200 can be applied in the following places:
Table service
Quick registration
Inspection
On-line sales
1.4 External Overview
The MODAT-200 combines its features in a stylish enclosure. The MODAT-200 consists
of a screen, rear panel, top panel, bottom panel and two side panels (left and right). The
panels are described in detail in the following sections.

MODAT-200
Page 4
1.4.1 Front Panel
The front panel of the MODAT-200 is shown below.
Figure 1-2: MODAT-200 Front Panel
1 x Speaker
1 x Wi-Fi/Bluetooth status LED
1 x Battery status LED
4 x Touch keys
The two LEDs on the front panel indicate Wi-Fi, Bluetooth, battery and message status as
described below.
Wi-Fi/Bluetooth LED (Left) Battery/Message LED (Right)
Charging -- Orange
Incoming Message -- Red (blinking)
Bluetooth Connection Blue --
Wi-Fi Connection Green --
Bluetooth & Wi-Fi Switch between blue and green --

MODAT-200
Page 5
1.4.2 Left Panel
The left panel of the MODAT-200 is shown below.
Figure 1-3: MODAT-200 Left Panel
1 x Scrolling key
1 x MicroSD card slot
1 x Reset button
1.4.3 Top Panel
The top panel of the MODAT-200 has a power button as shown in Figure 1-4.
Figure 1-4: MODAT-200 Top Panel

MODAT-200
Page 6
1.4.4 Bottom Panel
The bottom panel of the MODAT-200 is shown below.
Figure 1-5: MODAT-200 Bottom Panel
1 x Earphone connector
1 x Mini USB connector
1 x Power charging cradle connector
1.4.5 Rear Panel
The rear panel of the MODAT-200 is shown below.
Figure 1-6: MODAT-200 Rear Panel
1 x Hanger
1 x Hand strap clip

MODAT-200
Page 7
1.5 Specifications
The technical specifications for the MODAT-200 systems are listed in Table 1-1.
Specification MODAT-200
Microprocessor Samsung 6410 ARM11 667 MHz
OS Windows Mobile 6.5
Memory 128 MB SDRAM
128 MB NAND Flash
Display 3.5” (89mm) TFT LCD
QVGA (240 x 320)
64 K color
LED backlight
Resistive touchscreen
Communication Wi-Fi 802.11 b/g
Bluetooth 2.0 + EDR
USB client
Storage One MicroSD slot (customer-accessible)
Audio 1 x Speaker
1 x Microphone
1 x Audio jack for the earphone with microphone
Buttons/Keys 1 x Power on/off button
1 x Rolling key
4 x Touch keys on front panel (calendar, start, OK, message)
Indicators 1 x Message/charging LED
1 x Wi-Fi/Bluetooth connection LED
Vibrator Yes
Power 3.7 V 1880 mAh battery (built-in, non-swappable)
Power Adapter Input: 90 V AC to 264 V AC
Output: 5 V DC, 1A (max.)

MODAT-200
Page 8
Specification MODAT-200
Temperature Operating: -10C ~ +50C
Storage: -20C ~ +70C
Humidity 5%~95%, non-condensing
Drop Survival 1.2 m
Protection IP 54
Electrostatic Discharge +/- 15 kVdc air discharge
+/- 8 kVdc contact discharge
Dimensions (LxWxD) 125 mm x 174 mm x 18.7 mm
Net Weight 200 g
Certifications UL, CE, FCC
Table 1-1: MODAT-200 System Specifications

MODAT-200
Page 9
1.6 Dimensions
Figure 1-7: MODAT-200 Dimensions (units in mm)

MODAT-200
Page 10
Chapter
2
2 Installation

MODAT-200
Page 11
The installation steps below should be followed in order.
Step 1: Unpack the device
Step 2: Check all parts are included
Step 3: Charge the MODAT-200.
Step 4: Power up the systemStep0:
2.1 Unpack the Device
WARNING!
Only remove the protective plastic cover stuck to the front screen after
installation. The plastic layer protects the screen surface during
installation process.
To unpack the MODAT-200, follow these steps:
Step 1: Cut the sealing tape. Only cut deep enough cut the tape.
Step 2: Open the box.
Step 3: Lift out the device.
Step 4: Remove all the peripheral parts from the box. Step0:

MODAT-200
Page 12
2.2 Packing List
The MODAT-200 is shipped with the following components:
Quantity Item Image
1 MODAT-200
1 USB cable
1 AC-DC Adapter
90 V~264 V AC input
5 V DC output, 1 A (max.)
1 Earphone with microphone
1 Leather bag
1 Stylus